the upgrade of my DOCSIS 3.0 cable modem is my compatible wireless router?

Similar Questions

• NETGEAR N300 Wi - Fi DOCSIS 3.0 Cable Modem Router (C3000) sees the backup HD Seagate but don't transfer

  V1.01.11 firmware, OS is Windows 10

  I bought the cable Modem Wifi Netgear N300. Except for the external hard drive Seagate (backup Seagate more 5 TB desktop external hard drive with 200 GB of Cloud Storage & Mobile Device backup USB 3.0 (STDT5000100)), all my devices connect to it without problem. However:

  1.) when I have the hood upwards the Seagate external hard drive, the genius of Netgear he sees, but says that the drive has 0 bytes available.

  (2.) that's why I can't back up by using the backup program WIndows 10 but

  (3.) I can "manually" drag files from my PC to the Seagate HD (the PC is connected to the modem router cable via wifi.)

  4.) when I connect the Seagate HD with a USB cable to the computer, the backup works.

  It's frustrating because I want to use the Seagate HD as a backup for some of my devices and I want the devices to send their data or the Netgear router.

  Can someone help me? It seems important that Netgear genius sees the HD Seagate but think it has no place.

  Richard

  I answer my own question (!) but is the answer that the HD 5 t is not compatible with the cable modem Netgear router? See:

  http://KB.NETGEAR.com/app/answers/detail/A_ID/18985

  Richard T.

• WRT610N and Motorola SB6120 DOCSIS 3.0 Cable Modem

  I've upgraded to the modem DOCSIS 3.0 in October due to higher bandwidth offerings of Comcast cable.

  Everything was fine until last week when I had recurring loss of Internet connectivity requires me to reboot/cycle my WRT610N and/or modem.

  I updated the firmware of the currently displayed 1.00.03 B15 and reset the router.  This did not help the situation.

  I also tried the suggestions mentioned here, including the Beacon Interval 75, threshold of Frag 2304, threshold RTS 2307, the wide-40 MHz Radio band.  Reset and cycled the router and modem after all this.  I also tried to power off my computer after each reset, all to nothing does not.

  I'm still losing Internet conncectivity several times per hour.  LELA is unable to repair the connection.  So far, the only solution is to reboot the router.

  Do I have a defective router (still under warranty), or is there a problem to interface with DOCSIS 3.0 modems.  Never had this problem with the old Comcast cable modem.

  My WRT610N is version 1 material.  Wireless encryption is WPA - AES, recommended by Beaver in a previous post in August.  Nothing is connected to the USB port on the router.

  Results of 'ipconfig/all' as follows:

  Microsoft Windows XP [Version 5.1.2600]
  Copyright (C) 1985-2001 Microsoft Corp.

  C:\Documents and parametres\joe > ipconfig/all

  Windows IP configuration

  Name of the host...: jb
  Primary Dns suffix...:
  ... Node type: unknown
  Active... IP routing: Yes
  Proxy WINS active...: Yes

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : hsd1.ca.comcast.net.
  ... Description: NVIDIA nForce Networking Controller
  Physical address.... : 00-14-22-xx-xx-xx
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  IP address...: 192.168.1.107
  ... Subnet mask: 255.255.255.0.
  ... Default gateway. : 192.168.1.1.
  DHCP server...: 192.168.1.1.
  DNS servers...: 192.168.1.1.
  Lease obtained...: Thursday, November 19, 2009 19:04:46
  End of the lease...: Friday, November 20, 2009 19:04:46

  I "x-out" the last 6 digits of my MAC address for security reasons.

  I would be very appreicate suggestions.  I strongly suspect that I would like to order a replacement from Linksys via warranty RMA router.

  Thank you for reading this.

  Sincerely,

  Joe

  Received the replacement router on 22-11-09.  WRT610N rebuilt with firmware v 1.00.03 B15.

  Installed with the current LELA software.  Wireless laptop was runing Vista 32-bit, Wired PC on XP Service Pack 3.

  Everything works normally again.  Replacement router dropped not a (wired or wireless) connection since its installation.

  I find that my original router (bought about 3/09) was defective.

  After replacement of the router, I upgraded my OS to Windows 7 (32-bit on laptop wireless, 64-bit Wired desktop).  No problem at all with the router.

  Hope this helps others.

  Joe

• my laptop has completed the automatic update of vista and after that I can't access wireless router with an ethernet cable only

  My sony vaio laptop running windows vista has completed an automatic update and after that, I can't connect to my wireless network, I can access the internet with an ethernet cable.

  It worked perfectly fine before the update, I know that there is a problem with what I had the same problem in the past. The way it's been solved previously was to restore the laptop to an earlier point before the end of the update. Unfortunately I can't do that and the laptop has been completed, wiped and there is no backup where I can go to restore.

  I know I can remove some updates but don't know what 1, me it is another way to solve the problem.

  Your help would be much appreciated.

  Thank you

  Hi Nadzarif,

  You can try the following steps and check if it helps:

  Method 1:

  Because the wireless stopped working after windows update, you can check the Sony support link and try to install the latest version of the drivers for the wireless card and check if it helps:

  Sony support

  For more information, see the article:

  Update drivers: recommended links

  Method 2:

  Updated version has a problem in the history of the update.

  Step 1:

  You can check in the history of the update for the updates that are installed recently or before the show.

  a. open Windows Update by clicking the Start button. In the search box, type Update, and then in the list of results, click Windows Update.

  (b) in the left pane, click view update history.

  c. to display more information about an update, double-click it.

  See the Windows updates are installed

  Step 2:

  Uninstall recently installed updates and install the updates one at a time to understand what update is the cause of the problem.

  For more information, see the articles:

  Remove an update

  Install Windows updates

• Desktop HP Pavilion 500-374na: the upgrade of processor power and power

  Hi man, im planning on upgrading my food processor and the power tomorrow and just need to check that my choice is compatible?
  
  I have a HP Pavilllion 500-374na desktop pc, with a processor Intel Core i3 4150 and a power supply 180w.
  
  My scheduled updates are - image processor intel core i7-4790 3.6 Hz 8 mb L3 cache and corsair 500w PSU.
  
  The list according to the upgrade of processor hp provide it states that it is compatible with my motherboard, but just dream to double check before I commit.

  So, any help would be great guys?

  Hello

  You should not need a power supply upgrade. But just in case, open your PC and display the information on the label of power such as the amperage supply total wattage and 12v.

  Thanks for posting on the forum.

• Sysopt dnat error on the road when the upgrade

  I am trying to upgrade my PIX 515. I'm upgrading to 6.1 (2) 6.3 (4). After the upgrade and reload, I get a config error indicating that "no sysopt route dnat is obsolete. How can I get rid of this error on charging after the upgrade. I understand it's no longer use this type of sysopt.

  Thank you

  Mike

  write members

  The obsolete command is in your startup-config, save your running-config it will take off.

• On ethernet ESXi iface will not get the IP address of the cable modem

  I installed the Vyatta Core 6.3 virtual appliance in VMWare ESXi 4.1 U1 on a Dell Precision 490. I want Vyatta to serve as a single window for my home network together with a red interface with a public IP address, other VMS behind the DMZ and my private machines (laptops, TiVo, etc.) behind the Green interface.

  Here is my VMWare network topology:
  vSwitch0 ("green vSwitch"): NIC 0, connected to the hub of switching/wireless connection with connection cable
  vSwitch1 ("demilitarized vSwitch"): no physical NETWORK adapter
  vSwitch2 ("red vSwitch"): NIC 1, connected to the modem cable Comcast with connecting cable
  Here is my config of Vyatta VM network:
  eth0: connected to vSwitch2 ('Switch red')
  eth1: connected to vSwitch0 ("Green Switch")
  eth2: connected to vSwitch1 ("Switch demilitarized")
  Here is my config Vyatta:
  Ethernet eth0 {}
  dhcp address
  Description "red Interface.
  automatic duplex
  HW - id 00:50:56:3F:FF:01
  smp_affinity auto
  automatic speed
  }
  Ethernet eth1 {}
  address 172.16.122.1/24
  Description 'green Interface.
  automatic duplex
  HW - id 00:50:56:3F:FF:02
  smp_affinity auto
  automatic speed
  }
  Ethernet eth2 {}
  address 192.168.122.254/24
  Description "DMZ Interface.
  automatic duplex
  HW - id 00:50:56:3F:FF:03
  smp_affinity auto
  automatic speed
  }
  My Green interface is very well. All computers connected to NIC of the model Dell Precision 0 get the IP addresses assigned to them via DHCP, which I put in place for this subnet/interface.
  My DMZ interface is very well. I can assign static IP addresses to the other virtual machines, assign their interfaces to vSwitch1 ("demilitarized vSwitch"), and they can communicate with each other.
  By my firewall or zone rules, the machines on the Green interface can communicate with machines on the DMZ, very well, and DMZ machines can establish connections to the machines of the green zone, which is correct.
  Here's MY PROBLEM: eth0 can't get an IP of Comcast address. I tried to change all sorts of locations on the ethernet card virtual vSwitch, etc., nothing helped. I rolled the cable modem power, nothing helps. When I connect my modem cable back to my old wireless router, the router receives an IP address immediately. When I connect the cable modem to 1 NETWORK card on the Dell printer, Vyatta gets no IP address.
  I'm sure I'm just something wrong, but I don't know what. I have a different configuration of Vyatta identical-except-physics somewhere else, but it doesn't seem to work practically
  . I think that it has to work, otherwise why Vyatta would provide an easy to use ESXi device that's read-to-go?
  I thought that maybe the vSwitch in ESXi were getting in the way and I need to connect the virtual machine directly to the physical NETWORK card, but you can do that in ESXi, so it's obviously not.
  No idea what is the problem?

  Answer is here: http://www.vyatta.org/forum/viewtopic.php?p=133590

• Linksys CM100 Cable Modem USB if it works on Windows 7

  IM upgrading vista to windows 7... will my linksys cm100 works on windows 7.

  Hi jackjam,

  Linksys CM100 Cable Modem USB is compatible with Windows 7.

  For more information, see the link:

  http://www.microsoft.com/windows/compatibility/windows-7/en-us/Details.aspx?type=Hardware&p=Linksys%20CM100%20USB%20Cable%20Modem&v=Linksys&uid=CM100&l=en-US&pf=0&pi=13&c=Networking&sc=Modems&os=32-bit

  You can also run the Upgrade Advisor before you perform an upgrade installation. It scans your PC for potential issues with your hardware, devices, installed programs and recommends what to do before upgrade you.

  See the link to download the Upgrade Advisor:

  Windows 7 Upgrade Advisor

  Also check out the link:

  Upgrade Windows Vista to Windows 7

  Hope this information is useful.

• cable modem-wireless combination or not?

  Hi, I'm going to switch from DSL to cable T - W (the only option in my building). I have an Airport Extreme on my TimeCapsule (it is the 500 GB disk version), that I use with my laptop. The iMac is connected to the router. I looked around at best buy where they sell T - W "approved" networking gear. Modems cable, all seem to be modem + units of combination of WiFi router at various points in price between about $80-200. My question is this: that any type of material that I use as long it's T - W compatible/approved. Any thoughts on the units of combination or is a cable modem + my Airport Extreme way to go. Not sure of the speed yet, but it is unlikely that I will contract for what that either more than 50 Mbit/s and perhaps even to 15 Mbps. Support some of the Motorola units that I was looking for very high flow rates, but they use the channel binding to achieve this goal. I read somewhere that if you buy the combined devices, you cannot update the firmware, but that doesn't make sense to me.

  Ask TW a modem without router built-in. And then run an Ethernet cable from the Ethernet port of the modem on the WAN on your AEBS port. You can connect your computer to the router either wired or wireless. It is the best configuration.

  If you do not need for Ethernet, then you can use a modem cable with router Wi - Fi as well. The main disadvantage is the difficulty you might have try to expand the modem/router using Apple hardware.

• I bought a Sony BDP - S185 connect Netflix Blu - ray player. I can't connect to the wireless router. Why?

  I just bought the blu - ray BDP S-185 drive so that I can access the internet (netflixetc.) on my new samsung tv. I tried to connect to my wireless router, but repeat me my connection type iswired and the connection has failed. Can I connect this player to a wireless router or should it be connected to the router? Difficult because the router is in the basement and the television on the third floor. Can I use the separator on phonejack (existing in the 3rd and.) and connect the two phone and blu ray player or do I need a netgear typedevice to connect this player? Thank you in anvance understand help. Sorry, it's so rambled butI am very confused here!

  Hi Robert,.

  Welcome to the community of Sony!

  This Blu - ray player is the BIV (Internet Video base) base model and does not support the wireless Internet connection. I suggest that you use the Ethernet LAN cable to connect the player to your router/modem.

  Thank you for your message.

• Desktop computer connected via a cable to a wireless router - can't print on Photosmart Wireless B109n-z

  Hello

  I have my desktop (Windows XP) connected via a cable to a LinkSys WRT54GC wireless router and wireless HP Photosmart B109n-z connected wireless. I can 'see' desktop printer if I write the IP address of the printer in the browser, but printing does not work.

  I don't know how to set up the printer to print from this desktop computer. What I choose when installing printer drivers (printing via USB or wireless?). I tried manually installing printer but without success. Do I have to set up specific ports?

  Printing from laptop (connected wireless to the router) works perfectly.

  Thank you in advance for your answer, I'm really lost on this one.

  Choose print wireless while installing the software.  Because the printer is connected to your router, you don't need to go through «setup USB wireless»

  I'll try to manually add again in this way:

  Verify that you can access the web page internal to the printer by its IP address.

  1. click on the 'Start' button--> printers and fax machines.
  2. under print jobs, click on "add a printer".
  3. click on 'Next' on the Add Printer Wizard window.
  4. Select "local printer attached to this computer. Deselect "automatically detect and install my Plug and play printer." Click "next".
  5 under, select a Printer Port option, select "Create a new port" and choose "Standard TCP/IP Port" and click "Next".
  6. in the "Welcome to the Add Standard TCP/IP printer port Wizard" make sure that the printer is turned on and connected to the same network that your computer is connected to. click on the button "next".
  7. under "Add Standard TCP/IP Printer Port" enter the IP address of the printer. Click 'Next' and then click 'Finish '.
  8. now select HP in the manufacturers list, select your printer in the list of the models of printers and click the button "next".
  9. If you can't find your printer, you will need to find the installation CD and use the 'Disc' option to select one of the files hp*.ini. You can also select another model of the same type HP printer.
  10. Add the name of print spooler, and then click "next".
  11. click on "next".
  12. click on "Next" and "Finish."

• Mac book air cannot detect my iPhone 6, after the cable on my I phone 6 to connect with my mac book air, nothing appear on the mac book. Seems like it can't detect the file i phone 6. I want to export my photos and do the upgrade version.

  Hi, after plug the cable on my phone i 6 to connect with my mac book air, nothing appear on the mac book.

  Seems like it can't detect the file i phone 6. I want to export my photos and do the upgrade version.

  Current situation is nothing exportable phone and also cannot do anything mac book because they cannot detect each other. Please advise, thank you.

  You can try to move to a different USB port. And if your just trying to swap photos try Airdrop. Also try to go here If iTunes does not your iPad, iPhone or iPod - Apple SupportHope this help, good luck to you.

• Upgrading from Windows XP to Windows Vista and now I can not find wifi or when I try to connect to the internet, I get an error, "a cable is not plugged on the network card.

  Wireless connections

  I upgraded my dell vostro laptop 1000 Windows xp to vista and now I can not find wifi or when I try to connect to the internet I get an error, "a cable is not plugged into the card network", "connection to the Local network. Everything worked fine until I upgraded. I noticed in my device manager, the driver for the system controller and core network are not installed. Could it be the problem? Is someone can you please help me understand this?

  Hello

  I noticed that you had created another similar to this question. Have you tried the steps suggested in this post?

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/how-do-i-put-WiFi-back-on-my-PC-after-upgrading-to/c9b90ec1-8393-4B57-b4af-2fbeb802af58

  You can also try the following methods and check if it helps.

  Method 1:

  Update a network adapter driver.

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2:

  Troubleshoot network adapter problems.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

• Cannot turn off after the upgrade to 10.11.4

  I have a late 2012 3.4 ghz i7 iMac / 32 RAM 10.11.4 running (and other iMacs around the office): I can't stop. When I try a stop down (after removal of servers/TimeMachine, close all applications - even unplugging the ethernet cable) - it goes to a black screen with the "circle of rotation of lines." They will be 'spin' this weekend if I let him. Instead, I'll put the machine to sleep during the week and make a hard cock down via the power button Friday night.

  I think it has something to do with the upgrade to 10.11.4. I have reset the PRAM and tried also to start up in the 'hidden' startup disk and first aid running without result. Tried to find preferences for throw - unsuccessfully - Finder found "com.apple.finder.sfl" I should throw?

  Another change is that now I'm using a new Pegasus2 18 to RAID hooked up via "2016" MacMini and Apple server software (replaced my Apple XServe)

  Someone at - there a method I can use to stop? Thanks for your help!

  Please read this message before doing anything.

  This procedure is a diagnostic test. It is unlikely to solve your problem. Don't be disappointed when you find that nothing has changed after you complete it.

  The test is intended to determine if the problem is caused by a third-party software that loads automatically at startup or logon, by a device, by a police conflict or corruption of system files or some system caches.

  Disconnect all devices wired except those required to test and remove all the expansion cards from secondary market, as appropriate. Start in safe mode and log on to the account of the problem.

  Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. Ask for additional instructions.

  Safe mode is much slower to boot and run as normal, with limited graphics performance, and some things work at all, including an audio output and a Wi - Fi connection on some models. The next normal boot can also be a bit slow.

  The login screen is displayed even if you usually connect automatically. You need your password to log on. If you have forgotten the password, you will have to reset it before you begin.

  Test in safe mode. Same problem?

  After testing, restart as usual (not in safe mode) and make sure you always have the problem. View the results of the test.

• Engravers Blu - ray Samsung SE - 506 Monte is more after the upgrade of the El Capitan

  Hi all

  MBP, in early 2008, El Capitan 10.11.2...

  My Samsung Portable Blu - ray writer, SE-506CB/RSBD Monte is more after I upgraded to El Capitan, last week.  The drive itself is only a few months old.

  The problem is not the USB ports, like other devices work fine with all the USB ports on my MBP.

  Note that I'm NOT trying to read or write a Blu - ray disc.  I try only to play audio CDs, I've done successfully before the upgrade to El Capitan.

  Someone had this problem?

  Thank you...

  For what it's worth, I have this problem as well.  The drive tray would not eject even with a single cable, so I switched to another.  I could then open the drawer (seems odd for me) but the disc would not rise.  Here's the info from the console log that indicates that the operating system is getting bad feedback from the pilot saying that the disk is defective.  This same drive/cable/disc work very well on my MacBook Air 10.10.5 and had worked perfectly well with this MBP even before the service (and "free" upgrade to EC by Apple).

  Console

  09/01/16 12:34:49.000 kernel [0]: AppleUSB20HubPort@fa130000 011849.735343: AppleUSBHostPort::resetGated: a new attempt to list 100 MS

  09/01/16 12:34:50.000 kernel [0]: AppleUSB20HubPort@fa130000 011850.924723: AppleUSBHostPort::resetGated: a new attempt to enumeration in 200ms

  09/01/16 12:34:51.000 kernel [0]: AppleUSB20HubPort@fa130000 011852.236095: AppleUSBHostPort::resetGated: a new attempt to enumeration in 400 ms

  09/01/16 12:34:52.000 kernel [0]: USBMSC (non-unique) identifier: (Korean characters removed) 0xe8d 1956 0 x 0 x 0, 2

  09/01/16 12:35:10.000 kernel [0]: disk3: alignment error.

  09/01/16 mds 12:35:12.432 [74]: (Volume.Normal:2464) volume: 0x7ffc330a4c00 * initiated creation of occluding a default location: 1 SpotLoc: (null) SpotVerLoc: (null): 0/Volumes/ENTOURAGE

  09/01/16 mds 12:35:12.456 [74]: vsd:0x7ffc33173400 (Volume.Error:577) open failed.  failureCount:0 (null)

  09/01/16 12:35:23.000 kernel [0]: smb_smb_ssnsetup: GROUND does not support extended security, this server will be deprecated in the future!

  09/01/16 mds 12:35:27.471 [74]: context of recycling: 0 (Volume.Normal:166) vsd:0x7ffc33173400 DisabledStore: {}

  DisabledRecycleCount = 1;

  }

  09/01/16 mds 12:35:27.502 [74]: vsd:0x7ffc338c6000 (Volume.Error:577) open failed.  {failureCount:1}

  DisabledRecycleCount = 1;

  }

  09/01/16 mds 12:35:57.502 [74]: (Volume.Normal:166) vsd:0x7ffc338c6000 DisabledStore recycling: 2 context: {}

  DisabledRecycleCount = 2;

  }

  09/01/16 mds 12:35:57.540 [74]: vsd:0x7ffc308c8400 (Volume.Error:577) open failed.  {failureCount:2}

  DisabledRecycleCount = 2;

  }

  The drive works perfectly well with this disc in 10.10.