try connecting a printer, mobilefoon or e-reader for my laptop USB port I ad, 2 and 3

Similar Questions

• HP Deskjet 1010: Wireless printing through a TG1672G of ARRIS, use the USB port on the modem?

  It is possibel to print wireless with a TG1672G of ARRIS, use the USB port on the modem?

  Hello

  There is no print server function so you can not:

  http://gditechnology.com/manuals/Arris_TG1672G_Data_Sheet.PDF

  Kind regards.

• where is the fingerprint reader for a laptop of HP TouchSmart tx2-1025dx

  where is the fingerprint reader for a notebook PC HP TouchSmart tx2-1025dx help please

  Hernandezeric2, welcome to the forum.

  Here is a guide that has a video on how to configure the fingerprint reader.  It should show you the location of the reader.

  Please, click on "Thumbs Up +" if I helped you and click "Accept as Solution" If your problem is resolved.

• Mobile gamepad XBOX 360 not recognized when connected to a Windows 7 64 bit Home Premium computer USB ports

  Very well - so a few days ago (Saturday ~ 2) (25. 2012) I connected to my XBOX 360 (Wired) controller on my Toshiba Satellite L655 computer laptop with Windows 7 ~ Home Premium 64-Bit. To my surprise, a Notification bubble popped up from the taskbar, saying that the "unrecognized USB device. It has malfunctioned. "

  Naturally, I took, waited a few seconds, and then reconnect the USB key. The same message has popped up. Now, I was angry. Repeatedly, I took and reconnected it all a few seconds until that FINALLY the 4 green lights around the button Guide everything illuminated and then back except the one on the upper left, which was the way it should have been.
  I went to the control panel and clicked on the 360 controller to see if he had any input. Nope.
  I pulled out once more, has waited a while and plugged in. No, lucky. The same thing happened again. The Notification bubble came, all 4 green lights on and then all four of them died. I don't know what happened.
  When I plugged the controller to the laptop the FIRST FULL TIME, he installed all necessary drivers in less than a minute and I was on my way. Every time after that, I have taken the controller into the USB Port and began to play. Now all the time, that is to say that it cannot recognize the controller?
  I've tried everything, even a system restore. Nothing did. I've uninstalled and reinstalled the drivers for a few minutes, there was an entry of the controller, then he went just blank.
  I need this controller in order to play my racing games, seeing the keyboard control just aren't the best. I don't know what the problem is, but I wish I had a solution A.S.A.P. Please, Microsoft, please. Help me!
                                                                                                                          
  
  
  
  

  I had the same problem, cannot find a solution that worked everywhere, including Microsoft support forums.

  About to give up, I remembered the old cure NDA, shaped, "why not?"  I've tried everything else. "So I've disconnected everything on the gamepad, blew in every connection and reconnected everything, by ensuring that the connections were tight.

  It has worked perfectly since then.

• Connect the printer network of windows 7 for XP

  After select printer finds he cannot find printer driver fothen I click search manually, I need to know where the specific drivers for windows 7 looking for deskjet 5550 drivers which is load in windows, I have isntalled the printer on this workstation to be sure it was the drivers, HP printer uses the name of the different driver than the name of the printer?

  Hi Vegasshadows,

  Welcome to the Windows 7 community!

  From your problem description, I understand that you can not connect to the network from Windows 7 to Windows XP printer. I take this opportunity to help you.

  I suggest the following methods and check if it helps to solve the problem.

   

  Method 1: Install a printer

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer

   

  Method 2: Find and install printer drivers in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  For any further assistance, I suggest you to contact HP printer Support.

  Here is the link: http://www8.hp.com/us/en/support-drivers.html

  You can also check out the links below in case if you have other problems with the printer.

  Printer in Windows problems: http://windows.microsoft.com/en-US/windows/help/printer-problems-in-windows

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

   

   

  Kind regards!

• I went to download the latest Adobe Reader for my laptop.

  When I put the search in Google "Adobe Reader" he mentions the first point of contact in the results with what appears to be a hyperlink bound to adobe.  When you click the link, it downloads the file of execution and by opening the file, I realized that it wasn't in fact Adobe Reader, but a malicious malware execute virus that seriously screwed up in my registry and now I have to reformat my computer.  CAN ADOBE PLEASE DO SOMETHING TO GET RID OF THAT LINK, SO THAT HAPPEN TO SOMEONE ELSE IN THE FUTURE! : I'M NOT HAPPY ABOUT IT AND IT SEEMS TO ME THAT YOU GUYS NEED TO CONTROL UNTIL WE * LIKE THIS.

  Here is the screenshot.  The first 2 links are TWO links viral malicious software malware.  PLEASE DO SOMETHING!

  

  Adobe has no control over the content of Google.

  To download an Adobe software, don't google it, but start here: http://www.adobe.com/ and then click downloads.

• HP Deskjet 3000: Problem WI - FI wireless connection for computer laptop-flashing blue light on the printer

  Blue light on my printer is blinking and laptop unable to connect to print

  Hello
  
  Thank you for using the HP forum. You can try the following:
  
  Please download and run the HP Print and Scan Doctor (PSDR) tool to diagnose and solve your problem
  
  http://h20180.www2.HP.com/apps/NAV?h_pagetype=s-926 & h_lang = on & h_client = s-h-E016-1 & h_keyword = DG - PDU
  
  Hope that helps.

• HP Deskjet 3545: hp deskjet 3545 my desktop pc does not connect to the printer via the usb port

  Hello

  I installed all the drivers and the software correctly and the printer can communicate with my desktop pc for problem analysis, but when I open an editor like notepad, word, write something in them or when I open a photo and when I try to print, it cannot communicate with the printer. I used same HP print and Scan Doctor in order to study the problem by clicking on the button "Correct the impression", in the program, he sees even my connected printer (usb) or same (LAN), but printing HP and Scan doctor after reviewing all the steps and ticks as ok, when he said "try to send the test page" and when he tries to send it to the printer It does not send and I choose "no print" to see which program will thus be, discover the program this time said "send the in-house test page", and I chose this option to send it internally and the printer works. The program says "there is a problem which can not find this application for assistance. try to uninstall and reinstall the drivers as an adviser"but I uninstalled and reinstalled the drivers and seems that there is no error, or any problem with the drivers, but seems that it cannot connect to the printer, even if I can use the scanner of my office and it connects to the printer without problem. What can be the problem? How can we solve this problem? any help would be appreciated. Thank you. Windows XP Professional Edition, 32-bit SP3 is installed on my desktop.

  Sincerely

  Hello metehangunaydin,

  Please try the procedure below so that you can at least be able to print.

  1. click on the Start button on the computer.
  2. then click on Control Panel.
  3. then printers and faxes
  4. in the top left, click on add a printer
  5. click Add a local printer
  6. and while "Use an existing port" is selected, select "Virtual USB port... "and then click Next.
  "7. in the manufacturer list, select HP, then under the Deskjet 990 c printer list", then click Next and complete the wizard

  Now try printing. It should work.

• LaserJet p1505 for connection wireless printing

  I have a Laserjet P1505 (not 1505n) a Net Gear N600 dual band Router router with USB port and printer. I tried to connect the printer USB cable to the USB port on the router and installed the printer on the laptop (a Windows Vista) I'm trying to save up for a wireless printing capability. The updated drivers from HP Web site, set to turn on printer 'sharing' but the printer does not appear in the network and sharing Center. Have directly connect the printer USB cable to the computer laptop USB port to print from the laptop.

  I missed something or cannot print via the router P1505 (without the "n")?

  Thank you

  I found a post where a similar problem has been resolved. The user has enough to show what he has done to help others like you. I hope this helps.

  OfficeJet 7210 won't install with Netgear N600 router

• When I try to turn on my PC it reads windows not load correctly

  When I try to turn on my PC it reads windows did not load correctly.  Go ahead and load up but it will do several times before of icons appear on the desktop.  When I try to go to the internet and the fact many times.  Sometimes it can show dupping 100 files.  Do I need another computer or if I can do something that will help stop this?

  Original title: hard to load PC

  Hello

  Perform the steps from the link below and see if it helps.

  What to do if Windows does not start correctly

  Hope this information helps.

• Connect the printer via the home router

  I have LaserJet CP1525, who has a wireless option... recently I moved my router on the different floor and can not connect to my my wireless home network option trough ethernet cable/router...tried on the printer, but "failed to connect".

  any ideas? Thank you

  Hi BoleczekNieduzy,

  Welcome to the HP Forums.

  I see that you have any questions, set up the printer on the network cable and even the wireless network.
  I will do my best to help you with this problem.

  Cycle power to the router.

  First, we must restore the defaults on the printer.

  Press the OK button on the printer, go to the service, and then select restore default settings.

  Print a printer configuration page to make sure that the IP address and SSID are erased.

  Print a Configuration report.

  Select the method.

  Uninstall the printer software.
  Insert the software CD into the CD drive.
  Follow the on-screen instructions.

  When you are prompted, select the connection through the wireless network.

  If you're still having problems, restore the default values and follow this method:

  Connect the printer to the router with an Ethernet cable.
  Wait about 1 minute and the printer must have a valid IP address.
  Print the configuration page to get the IP address of the printer.
  Type the IP address in the address bar of Internet Explorer which should open the printer's built-in web services page.
  Installing wireless over here now.
  Click the networking, wireless on the left, fill in information about the network and apply the settings.
  After the confirmation, then disconnect the Ethernet cable.
  Now you should have a flashing light on the printer in 1 minute wireless about.

  Run the installation again.

  I have provided a document to configure the wireless connection, or you can follow my different methods provided.

  Installation of the software of the printer on a wireless network or network (Ethernet) cable.

  If the Wireless does not always connect, to view these settings on the router.

  You have a double router broadband?
  If it is set to 5 GHZ network, you may need to change to 2.4 GHZ. (rename the 5 GHz or turn it off)
  The WPA key setting must be on AES to work properly not TKIP.
  If it is set to the 64-bit encryption, then change it to 128-bit.
  Multi flow must be enabled.
  Router firewall must be open for printer ports.
  If you have Mac filtering give you printer hardware to meet the needs of the configuration page.

  Please let me know if this is not the problem.

  Have a great day.
  Thank you.

• Install a (wired) ethernet connected the printer on a wireless network

  I just bought a laptop from HP dm4-1050ea with Win 7 operating system 64 bit & s5780uk PC HP Pavilion Slimline, with Win 7, 64-bit operating system. I have a HP2610 Photosmart printer that is currently connected to a Dell PC, Win XP SP3, via the USB port. I want two HP computers connect to the HP printer via a Netgear DGN2000 wireless router wirelessly. I understand that the HP printer needs to be connected to the router via ethernet, however, I don't know how to proceed with the installation. The installation CD supplied with the printer's 6, Win XP, and I don't know if I should be downloading drivers to the computer laptop dm4 and Pavilion PC or just one of the computers?

  Any help on the steps to take and the order to take would be most appreciated

  Best regards

  Rathbane1

  For step 4 you have not need must be connected to the printer. As long as the printer is already connected by cable to the router it will be accessible wirelessly on the two computers during the installation of the software.

• I have just connected my Apple G Drive (external drive) to my Laptop Microsoft - EXTERNAL HARD DRIVE - NOT RECOGNIZED. Help? Mapping drives?

  I just plugged my Apple G Drive (external drive) to my Laptop from Microsoft.

  Driving light - ON

  (It works fine on my MacBookAIR)

  EXTERNAL HARD DRIVE on the laptop computer of Microsoft Vista-

  EXTERNAL - UNRECOGNIZED HARD DRIVE.

  Help?

  I tried the drive mapping?

  No drive letter that appears.

  I tried Microsoft DIFFICULTY IT PROGRAM - it does not detect there is a problem - nor did he fix it.

  I need help/help - thanks

  Hello Campbell,

  I would be grateful if you could answer the following question:

  1. what Microsoft Fix It have you tried?

  2. you receive an error code or message?

  3. have you tried to connect another external hard drive?

  Try to use an external hard drive on another USB port or another computer and check.

  I suggest to follow the steps below and we update on the State of the question.

  Method 1:

  Tips for solving problems of USB devices:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Method 2:

  Install the latest Windows updates

  This method will install the latest drivers for your external hard drive USB device.

  a. click the Start button, type Windows Update in the search box, and then click Windows Update in the results pane.

  b. click find updates. When the scan finished, click optional review updates.

  c. click on the check box next to the update, and then click install updates.

  d. If you are prompted, read the license agreement, then click I agree.

  e. follow the instructions on the screen to download and install updates.

  f. If you are prompted, restart your computer.

  If your problem still exists, go to method 3.

  Method 3:

  Reinstall the USB controllers.

  This method addresses the steps where the USB driver currently loaded became unstable or corrupted.

  a. click Start, type device in the area Manager Search , and then click Device Manager.

  b. expand Bus USB controllers. Right click on a device, and then click Uninstall. Repeat for each device.

  c. Once complete, restart your computer. Your USB controllers will automatically install.

  For more information:

  Contact the Apple Support:

  http://www.Apple.com/support/contact/

  I hope that the information above helps you.

• Problem connecting to HP DJ5900 via the USB port on the router

  HP DeskJet 5940, MacBook Pro, OS x 10.6.8.

  I want to connect the DJ5940 through my router (Speedport W723V) via the USB port.

  I see that the printer is connected to the USB port of routers and adding a printer on the MBP works.

  However, when I try to print, printing dialoge sas is printing (full % increases), but nothing is displayed and the status of the printer finally chnges for "printer paused".

  Is what I'm trying to do possible?

  Dean,

  Thanks for your help, but I went in a different direction: the Speedport router is EXTREAMELY oriented Windows, to the extent that it has nothing in the documentation to do anything with a Mac, so I've dug a former print USB/Ethernet of Axis Communications Server. At least 7 years old and no documentation, but connect to its IP address allowed me to set it up, and Macs connected to it directly.

• Photosmart 7960 installed via the USB port on the PC under Win XP Pro acting as a print server

  I have a PC running Windows XP Pro, which acts as the home network file and print server.   The Photosmart 7960 is connected to this computer via a USB cable and configured to be "shared".   When I go to "Add a printer" on another PC, in Windows 7, which is also part of the same network, I can navigate to the 7960 correct, but the installation wizard is unable to find the driver for Win 7.  I still have what in the HP see basic documents that tells me how to add this shared printer on my Win 7 PC.  Looking at the support page drivers I saw that Windows 7 already has the driver.  True, but the only way, it seems that I can get to it is to connect the printer directly to Win 7 PC via a USB cable.   Any suggestions?

  Apparently, the solution is as follows.  First connect the photosmart 7960 directly to the PC running Windows 7 via USB cable network.  It will be auto-install drivers.  Reconnect the printer to the PC under XP pro server.   From the PC running Windows 7 where you have installed the printer via USB, you can go ahead and remove the photosmart 7960 from the list of printers; This will not remove the just downloaded drivers.  Next, select Add a printer, and then select 'Add a local printer' (no network).  Select 'Create New Port' and click Next.  In the next dialog box, type the name of the host server and the name of the printer.  In my case, it's \\mainserver\HP photosmart 7960. Click Next.   In the "Install the printer driver" dialog, click "Hewlett Packard" and find the 7960 in the printer list and click Next.  I was able to successfully install the printer this way.