Similar Questions

• iPhone 5 stuck in boot loop

  Hey everybody, I recently encountered a problem where I replaced one of my friend 5 iPhone battery and when I plugged it in to charge that he was stuck in a boot loop cycle. The Apple logo appear and disappear over and over again and never start.  I then read a lot of forums where people have had the same problem and tried a lot of things.  I even tried to put several other types of accumulators in the farm of origin, including, and none of them would allow the phone to initialize.

  I solved this problem by putting the iPhone in recovery mode where then iTunes could recognize.  I then did the update (not recovery) that was available, because do not get rid of all the data on the phone.

  I got a weird error that doesn't seem the case on internet "iTunes unable to connect to the iPhone. The value is missing.

  

  But the update worked!  Then I later discovered that my friend tried to update his phone when he died (battery was flakey, so why I replaced it).

  So if someone has ever an update failed and an iPhone stuck in a boot loop, just put in recovery mode and update the firmware from iTunes.

• T620 WES8 Image Capture failure/Boot Loop

  -t620 Quad Core

  -WES8 x 64

  -13WWDTBM602 #SABA #DABA

  -BIOS: L40 v2.05

  ------------------

  Tried an initial capture before making changes.  First capture failed quickly with a network card driver error - I've updated HPDM 4.6 SP1 and was able to continue beyond this error.

  Any following capture attempts result in a loop to initialize uneding.  The workstation creates a new boot option, "winpe [EMS ENABLED]", which he defines as a default value, which continually, it loads and restarts.  I have run this process for more than an hour before canceling the task.  All subsequent attempts create a new boot option or additional "winpe" with the same behavior.  I've updated the BIOS at this stage no change.

  I also found that I am unable to the hell UWF until the administrator is to go to the taskbar or the HP unified write filtering via the control panel Configuration.  The lock is green and indicates the GUI of Configuration UWF UWF is activated but the new shortcuts office and downloads are left in place after the reboot.  Event viewer shows "event ID 1007:"unified write filter is not disabled, code 196608 output. "  The system does not have the specified path.  "I also tried to disable UWF using HPDM but received 14007032, write error filter.

  Write research through the Configuration of the filter, I found that there is NO file/folder exclusion, considering that the TC I just shot of the multiple box including bootstat.dat and agent_persist.dat.

  So... do I have a lemon here or what?  I have an another t620 that I confirmed I can disable UWF without any problems but I have not tried image but as I am a little worried about the boot loop and create the same problems that I saw with the original.  I'd be more comfortable if I could find a factory image HP download, but there is none available on the drivers & software page.  Can somene HP direct me to a factory WES8 x 64 image?

  Thank you

  ZP.

  We have completely uninstalled HDPM and reinstalled 4.6 with a new database and imagery with success the t610 older.  Then we have updated to 4.6 SP1 and we were able to successfully image the t620.

• Upgrade - unable to boot (probably error classpnp.sys) RAM

  Hi all

  I have an acer aspire 5742G with windows 7 Home premium Edition and 3 GB of RAM.

  I bought a Corsair Valueselect 2 x 4 GB RAM together. When I replaced the original/3 GB with the corsair, I was unable to boot windows.

  Problem mentioned here: http://www.tomshardware.co.uk/answers/id-1888966/windows-boot-memory-upgrade.html

  Basically, I get an infinite loop of "unable to start Windows. A recent hardware or software change might be the reason for this... »

  1 start windows normally

  2 start windows in recovery

  These two options are responsible and we're back to the same loop.

  After trying to boot into SafeMode (via F8), I could see the start-up hung at classpnp.sys

  I put the original RAM dos and windows started without any problems.

  Googling has revealed that this problem was already previously, but no solution has been put forward except: put the old memory.

  (http://forum.crucial.com/t5/Standard-DRAM-Memory/Windows-7-boot-failure-after-memory-upgrade/td-p/129972)

  I've updated BIO to the latest version, BIOS recognizes the 8 GB (in original and updated updated version).

  Any ideas / suggestions are welcome.

  Kind regards

  Update and closing:

  I went to the shop of pc and we tried the RAM from another manufacturer, ICUDU (2 x 4 GB 1333) and the pc started without any problems. I'm surprised that the manufacturer of the RAM has this impact it could work or not.

  I hope that this problem is not encountered by others, it was quite an experience.

  However, my conclusions are added below. As I mentioned in the first post, the problem has been experienced before and the 'solution' was a status quo, do not level. This experience taught me that not all RAM is created also. Even the best-known brands may be sometimes inconsistent.

  Summary:

  Upgrade of RAM 8 GB on an Acer aspire 5742G with i3 - 370 M processor:

  Upgrade memory ICUDU (2x4gb) Kit works,

  ValueRAM Corsair (2x4gb) - sorry to say - did not work.

  Kind regards

• Boot Loop iPhone 5 c problem

  So that's how iphone got a uppdate iTunes, but after she got into a boot loop.

  The phone can be switched on using the on/off switch, but it can be disabled by using only the power on + combo home buton!

  Powers on but right phone at the apple logo, it stay there for 3 seconds then the apple logo fades to grey (like an LCD) broken then there restarts... and that on and so on... until the battery is empty.

  The phone goes into DFU mode, itunes acknowledged, but after itunes launch the iphone in dfu mode, itunes says "waiting for iphone", the phone restarts, but instead to continue the restore procedure, it penetrates into the same loop and after 10 minutes, itunes gives error.

  The phone is out of warranty, and I want to record just because it seems perfect, no sign of use!

  Oh and another thing, I tried to put another apple original battery (I hade a new brand in hand 6!) did not work...

  So guys I came to you for your review. Be free to say what you think that will fix this poor iphone!

  I was about to say to make an appointment at the genius bar. They would try to restore it for you free of charge...

  Then I saw your mention of trying to put a new battery in there... If you have physically opened the phone upwards, it is technically unbearable and completely untouchable by Apple. I couldn't hurt to consider anyway and see if they can get it to restore, but you can kiss all hopes for a farewell to replace security exit.

• iMac 27 stuck boot loop

  my 27-in. Imac is stuck in a boot loop.  It goes to the start screen, I see the Apple logo and progress bar, then the screen has a line go overboard and it restarts. Attached picture to show you the screen, any help would be great. Thank you!

  Try to start in safe mode, try safe mode if your Mac does not commissioning - Apple Support

• Satellite L50 - A - 1 6: "boot loop" at power on

  Hello world.

  I have a Satellite L50 - A - 1 6 (just bought). I changed the HARD drive partitions in order to better utilize the space. Then I tried to create the recovery from the preinstalled recovery partition disk (However this was not changed!), but it did not work. It was posted this message: "the recovery partition was not found.

  So I tried to restore factory settings (as explained in the guide, press '0' at the beginning upward).
  After that, my laptop computer goes into "boot loop", and it continues to go in the boot loop every time I turn it on. The boot loop here is summerized: + logo (leading to innovation) toshiba-> error message (.. .has been detected a problem... etc etc)-> black screen-> logo toshiba (leading to innovation)-> ecc. ECC. +

  The only possible operations are:
  -to power the laptop off (by turn off by pressing the key)
  -to access Bios (by pressing the F2 key)
  but later, the laptop comes back still in boot loop.

  I also tried to set up an order of boot device for the use of tools like "live recovery cd" or similar (also USB)... but nothing... He always goes in the city "boot loop".

  Any suggestion to have the correct start of my laptop?

  Thanks in advance.

  Hello

  >. I changed the HARD drive partitions in order to better utilize the space. Then I tried to create the recovery from the preinstalled recovery partition disk (However this was not changed!), but it did not work. It was posted this message: "the recovery partition was not found.

  This does not surprise me. You have changed the partition table, and therefore the partitions of HARD drive will be more found.

  > So I tried to restore factory settings (as explained in the guide, press '0' at the beginning upward). After that, my laptop computer goes into "boot loop", and it continues to go in the boot loop every time I turn it on. The boot loop is summerized here: logo (leading to innovation) toshiba-> error message (.. .has been detected a problem... etc etc)-> black screen-> logo toshiba (leading to innovation)-> ecc. ECC.

  This does not work for the reason that I mentioned above. The disk HARD recovery isn't possible now!

  I recommend you to use stop force switch:
  http://APS2.toshiba-tro.de/KB0/TSB3C03JR0000R01.htm

• IX2 - DL does not start after the firmware update and now in boot loop contant with double red lights

  I just applied the update to the latest firmware 4.1.208.33789 for my IX2 - DL and it took an extremely long time to reboot - flashing white light for 20 min on the right.

  Shooting and by unplugging power did the same result.

  I hold the reset button hardware pin and now he's in a boot loop throw up double red lights and then attempt to restart with flashing blue white and strong.

  Help! don't know what to do next.

  Hello steveappcity,

  I recommend a support incident, opening the only way I can support an imager is if she is officially released:
  https://Lenovo-na-en.custhelp.com/app/ask/

• Satellite P100-347: blue screen at startup - unable to boot volume

  Recently, I left my 2 younger brothers playing NFS Carbon on my satellite P100-347, pre-installed with media center edition 2005, and now it fails to start.

  During the process of possibly starting a blue screen appears for about a second and then it shutsdown (I managed to make the words "unable to boot volume" on the basis of the blue screen).

  I tried to boot with a XP media center DVD but it gives me only a possibility of reinstalling the operating system with a cost of losing all my important data. Normally I would have picked up the system, but I don't want to lose my data.

  Can I do other than take it to a technician?

  Hello

  Well, for the most part the BSOD appears due to hardware problem or serious software.
  In your case, the software problem is possible

  Unfortunately, I think that the new installation of the OS is the best way to get the laptop works properly.
  Now, you want to know how to record data and the files well, I think that you should remove the laptop HARD drive and must try to connect the 2.5 HDD via external USB controller to another computer. Then you can save the files to the other HARD disk

  I think, now, you know that regular backups are important and necessary!

• Re: Satellite L650/07C-boot-loop after memory upgrade

  I have a Toshiba Satellite L650 / 07C - PSK1JA-07C017.
  To get a little more life out of it, I've updated yesterday with a SSD and 8 GB memory.

  The SSDS works perfectly and I have installed OS and all the drivers and software.
  However, the memory causes a boot loops. I returned to the standard 2 x 2 GB memory at the moment.

  With the new memory installed, the computer startup-loops. When you try to start Windows, the computer will appear at the stage of loading Windows (the boot animation) and then restarts.
  I tried to start with the recovery discs, and it arrives at the stage of loading of Windows Setup, and then restarts.
  She will continue trying to start, then by restarting (then repeat), until I turn it off.

  The memory I installed is Corsair CMSO8GX3M2A1333C9 (2 x 4 GB):
  http://www.Corsair.com/cmso8gx3m2a1333c9.html

  For me, it looks like the same specifications that the modules of memory Kingston 4 GB listed on the Toshiba site as being compatible with my laptop:
  http://www.MyToshiba.com.au/products/Accessories/memory/KTT-S3B/4G/accessories

  I found the specs of memory recommended here:
  http://www.LASystems.be/PDF/Kingston/246787/KTT-S3B4G.PDF

  If I go into the BIOS, I see that the memory is detected as 8192KB. The Toshiba site says that this laptop is expandable to 8 GB.

  Is there something I'm missing?
  Is there another step I need to perform when upgrading their memory?
  I don't know why it won't boot with the new memory modules in that I put.

  Thanks for any help you can offer.

  I assume you have the Australian model is not easy to find info on the hardware upgrade. What I can say is that model European uses DDR3 1066 MHz memory modules and 4 GB of RAM compatible a part PA3677U-1M4G number.

  It must be exact model described by microcens.
  I recommend you use the tested and compatible memory modules.

• Satellite L300D has decided to go a sort of boot loop

  My laptop decided to go sort of boot loop where it load and displays Toshiba screen, you can press F2 (for BIOS) or F12 (for the boot sequence) then shows a screen saying "Windows is loading files...". "with a progress bar and once who reached 100%, it restarts. Its kind of like the operating system does not recognize the HD. You can not press F8 to boot into safe mode or anything.

  Its a L300D Satellite from Toshiba with Vista

  I replaced the hard drive about a year on the computer and reinstalled vista OS with recovery disks and its been working very well. Ive tried reinstalling several times, ive also tried another hard drive and the same results with it also. I took the disc out and put it in a cage of external hard drive and can see everything ok. So I don't think it's a problem with the disk that initially, I thought it was.

  Ive also tried to format the drive (via the external hard drive cage) and resettlement, repair of vista, which dates back to the last know good configuration etc, but I just get the same results. I also downloaded and tried all the options with recovery of neosmart disk. And I can browse the hard drive at the command prompt ok, which lead me to think of the boot partition has been corrupted somehow. I thought the full format would be cured it but no luck. It comes down to the boot loop.

  So I'm running out of things to try.
  Any suggestions would be appreciated.

  Hey Buddy,

  Which disk you used exactly?
  Have you tested the Toshiba Recovery disk?

  If Yes, and the same problem exist, it appears to be a malfunction of the equipment. So, I would contact an authorized assistance service provider.

• HP pavilion 5CD3081TFX g6: hp pavilion g6 5CD3081TFX unable to boot from usb

  My hp pavilion g6 5CD3081TFX unable to boot from usb, since I have to clean install my Windows 10 operating system, when I press f10 after restart it asks password Admin, when I enter the password it shows disabled system? Any solution?

  @Suryakant2015

  Enter: 41694304

  Kind regards

  DP - K

• PowerMac G5 leopard in a boot loop

  Help! My G5 is stuck in a loop of start due a sorta app problem

  My PowerMac G5 is stuck in a boot loop because first my mac worked great until I launch TextEdit and he and all the other apps I opened after that always sit bouncing saying does not and I can't leave them so I tried Logout and it expired, saying he cannot leave TextEdit so my common sense knew Shutdown doesn't work so I forced shutdown and now It just WONT BOOT! Help, please!

  Garret

  Hi Garret,

  Could be many things, we should start with this...

  «Try disk utility»

  1 insert the Mac OS X installation disc, and then restart the computer by pressing the C.

  2 when your computer has finished booting from the disc, choose disk utility from the menu of the installer at the top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)

  * Important: Do not click on continue in the first screen of the installer. If you do, you must restart from the disc to access disc utilitaire.*

  3. click the first aid tab.

  4. Select your Mac OS X volume.

  5. click on the ERD, (not repair permissions). Disk utility verifies and repairs the disk. »

  http://docs.info.Apple.com/article.html?artnum=106214

  Then try a safe boot, (now shift key at startup), run disk utility in Applications > utilities, then highlight your reader, click on repair permissions, restart when done.

  (Secure boot can remain on the gray radian for a long time, let go, he tries to repair the hard drive & clear the caches)

  If by chance you do not have your installation Disc, try at least to the part starting secure from.

• Windows 7 HP boot loop

  I am running Windows 7 on a HP laptop and recently, I encountered a big problem. I clicked on the option "restart now" my updates after installation, let my computer it is the thing and went to bed. When I woke up I found it on the screen that says "cannot start Windows. So I ran the restore and he turned back, and then the update message come ask new restart now. I did it again, assuming error just randomly and my computer got stuck in a boot loop failed. I reformatted my hard drive and reinstalled Windows 7 and I thought everything was good, but now I find that things have returned to the way they are and now I'm back in the loop of bad starts. The signing of the problem is the following:
  Problem event name: StarupRepairOffline
  Signature of the problem 01: 6.1.7600.16385
  Signature of the problem 02: 6.1.7600.16385
  Signature of the problem 03: unknown
  Signature of the 04:21200948 problem
  Signature of the problem 05: AutoFailover
  Signature of problem 06:2

  Signature of the problem 07: BadPatch
  OS version: 6.1.7600.2.0.0.2561
  Locale ID: 1033

  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy. If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  MS - MVP - Elephant Boy computers - don't panic!

• Aspire 5920-6423 Boot loops before reaching the POST

  I have an Aspire 5920-6423, I've been working on a client and the device starts loop (IE: peripheral power light will appear for about 2 seconds and go offshore for 2 seconds... and repeat) several times (IE: from 3 to 10 {no constant number}) before messages and actually starts. I have never been a whitness to this problem and am stuck between the hammer and the anvil with her... Once it starts, the system works well and that it will continue in this way to stop battery low or dead.

  Course of the action:

  Fully charged battery not connected to current alternative... no solution

  Battery fully charged, not related to the sector... no solution

  No battery attached, not plugged into current alternative... no solution

  No battery no set, no hard drive connected, and to laugh without ram attached... always boot loop, but have obviously a mistake about ram.

  Any guidance on this issue will come as a blessing.

  Thank you!

  at this point, I think:

  1. a CPU problem
  2. hardware motherboard problem

  I don't have any other ideas.

• Iconia A1-810 taken in Boot Loop in any case to get it out?

  OK I admit it in a previous post, I was looking at getting the root privledges on my A1-810, I asked how to go in the Devolopers Options.

  Although I had put up to open the Options Devolopers and activation of Usb Debugging Options as well.

  But before I had the chance to do another thing my wife needed me to do something for her, so I stop my Tablet thinking I would come in a little bit and pick up where I left off.

  Evil

  When I started the shelf upward, he went through the usual boot process, but when he got to his home screen, stop immediately, started again and stop again.

  I went through this during about half an hour until I found a post on the forums that said.

  DO a Hard ReSet and will arrange the problem cause something got the Boot Mbr obstructed upward, and while I would lose everything on the shelf she set it to plug the factory and repair Boot Mbr.

  Well I preformed Hard ReSet.

  But it does not solve the boot loop in what it is.

  While he did reset it on specifications of the factory, I could tell that he began to return to the Welcome screen that guides you through the Setup program for the first time.

  You guessed it, he got to the home screen about 3 seconds later it restarted, and restarted.

  It went like that for well over an hour until I stopped him, with that alone be able to do using the reset button.

  A few times as it has been rebooted it came Android OS is upgraded software.

  Short saying I'm "VERY MAD".

  I can't quite understand what has happened.

  I never did anything, but go in the Devolopers Options.

  Short of sending new in Acer to be looked at.

  ANY IDEAS?    Anyway thanks for all the ideas in advance: Ricky

  If the unit is still under warranty, I suggest strongly back the seller as soon as possible, and it will become a problem Acer. You did nothing wrong, there is a software failure, and we all know that Android 4.1 and 4.2 are more than obsolete, so there is probably nothing you can do.

  I'm also stuck with serious problems in my Iconia B1 with 4.1.2 Android and there not there an even a chance that Acer will provide updates anytime soon, at least not in this life.