VPN3005 - PIX506 using NEM & IPP with split tunnel

Similar Questions

• SRP527W with Split Tunnel

  Hi guys,.

  I just sent a SRP527W that I had lying around for a while.

  Everything about the unit works as well as can be expected, however I have an obligation to perform split tunneling for VPN users.

  Currently, the only way that receives the VPN client is a default route. I noticed that on site-to-site VPN and tunnels GRE, you can specify safe routes, but I can't find anything that relates to remote VPN users. This can be done on IOS without problem, but would be good for the RPS.

  I'm under the latest firmware 1.01.26, so if I have not forgotten anything it would be probably for a future version?

  See you soon.

  Bryce

  Hi Bryce,.

  Nothing is overlooked, it is not possible to set up split tunneling for the VPN of the RPS server.

  Kind regards

  Andy

• Site to Site with split tunnel question

  I can't spilled tunnel to work on my router from production

  config:

  int serial 0/0/0

  External DESC

  Add IP x.x.x.x x.x.x.x.x

  NAT outside IP

  IP virtual-reassembly

  card crypto ipsec-map

  int fast 0/0

  DESC internal

  IP add y.y.y.y y.y.y.y

  IP nat inside

  IP virtual-reassembly

  overload of IP nat source inside the interface serial 0/0/0 of the 101 list

  Nat ACL

  access-list 101 deny ip 192.168.2.0 0.0.0.255 10.10.10.0 0.0.255.255 connect

  access-list 101 permit ip 192.168.2.0 0.0.0.255 any what newspaper

  card crypto acl

  access-list 102 permit ip 192.168.2.0 0.0.0.255 10.10.0.0 0.0.255.255 connect

  I can't get either to work but not together.

  Your thoughts are appreciated. I read about the order of operations with NAT, but still no dice.

  Steve

  Hi Steve,.

  I had a similar problem and got around it by using a map of pool and of course nat... This allowed me to divide the tunnel. First of all, get out your source line of nat ip inside the overload of the serial interface 0/0/0 list 101 and then add the following.

  NAT pool "pool name" "ip IP position of ' ' ext to(can be the same as ip ext to' netmask 255.255.255.252 ip

  IP nat inside source overload sheep pool «pool name» route map

  sheep allowed 10 route map

  corresponds to the IP 101

  !

  hope this works for you

  Thank you

  Andrew

• Problem with route on PC with split tunnel VPN

  Hi all

  I have the following situation:

  ASA 5515 X 8.6 running

  I have several inside sub interfaces:

  .10 = 192.168.10.124

  .11 = 192.168.11.124

  .12 = 192.168.12.1/24

  .13 = 192.168.13.1/24

  .14 = 192.168.14.1/24

  Now, I want to implement a VPN IPSec remote access:

  I attribute the range 192.168.99.5 to 192.168.99.50 for VPN clients.

  I have configured the tunneling split for the following networks: 192.168.10.0, 192.168.11.0 and 192.168.12.0

  They are also exempt from NAT.

  So the config looks good.

  The VPN is in place.

  However, when connecting to the VPN, none of these networks are available.

  After troubleshooting, I discovered the following:

  Received my card VPN IP address is 192.168.99.5 (as expected)

  However, when I make a copy of the itinerary, I see the following:

  Destination netmask gateway interface

  192.168.10.0 255.255.255.0 192.168.99.1 192.168.99.5

  192.168.11.0 255.255.255.0 192.168.99.1 192.168.99.5

  192.168.12.0 255.255.255.0 192.168.99.1 192.168.99.5

  The entry door to the routing of my PC table is pointing to a non-existent address, in my opinion it schould be on the same address as my adapter VPN (192.168.99.5).

  I tried this with annyconnect and the classic VPN client.

  Where I'm going wrong?

  No, this ip pointing 192.168.99.1 route is correct. It is not the cause of the problem.

• Access restricted without the split tunneling

  I'm disabled with Split tunneling VPN concentrator. Split tunneling has been disabled to carry the internet traffic of vpn clients via our internal web filtering server. But I must restrict access to my internal servers. How can I do that. I tried with filters/Rules but his does not work, and depending on the traffic of documents filter applies only to the traffic unencrypted.

  Thank you

  Avil

  If you use a VPN3000 while you can apply a filter to the users configured in group. This filter can restrict access to the servers as a list of specific protocols and access. This filter certainly applies to ENCRYPTED traffic, do not know what you are referring to your last sentence.

  You must first define the rules to define the traffic you want to restrict address., see here for more details:

  http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/vpn3000/4_1/config/polmgt.htm#1321359

  Define a filter, then add the rules you just set it to him:

  http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/vpn3000/4_1/config/polmgt.htm#1007037

  Thne go under the group that these users are configured with, and then apply the filter to it.

  A couple of sample filter are the following:

  Allow access to 10.1.1.2 and block everything else:

  To block access to everything, but 10.10.1.2, create a rule that is Inbound/Forward, Source of Anything, Destination of 10.1.1.2/0.0.0.0. Create another rule, it can be left at the default value which is incoming, drop, no matter what Source Dest what whatsoever. Create a filter with the default action of the front and add two new your rules, ensuring that rule that allows access to the host 10.1.12 is above the default rule which will pass everything else.

  Block access to 10.1.1.2, and leave all the rest:

  To allow access to everything except 10.10.1.2, create a rule that said, drop, no matter what Source and Destination of 10.10.1.2/0.0.0.0. Add a filter that has a default action is to send, add the rule to the filter.

  Notes:

  -You can allow or block access to subnets simply by changing your address/mask to something like combination: 10.1.1.0/0.0.0.255

• Split tunnel

  Hi guys,.

  I wonder if remote access VPN with split tunnel is using the home user or the corporate to surf internet connection own internet connection?

  Any help will be greatly appreciated.

  Thank you

  Lake

  Dear Lakeram,

  Split tunneling allows you to access certain resources through the tunnel and all other traffic will be sent to your local proxy.

  VPN traffic is defined by the VPN endpoint, for example:

  192.168.1.0/24---Internet---ADSL ASA VPN client-

  You can have the ASA push the network 192.168.1.0/24 to the customer. Once connected if the client tries to access everything that comes out of the scope of the network, this traffic will be sent to the LAN...

  Here's an example with ASA and router.

  ASA/PIX: Allow the tunneling split for the VPN Clients on the example of Configuration of ASA

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080702999.shtml

  ASA 8.x: allow the tunneling split for AnyConnect VPN Client on the example of Configuration of ASA

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080975e83.shtml

  Router allows the VPN Clients to connect to IPsec and Internet using Split Tunneling Configuration example

  http://www.Cisco.com/en/us/products/HW/routers/ps274/products_configuration_example09186a0080819289.shtml

  I hope it helps.

  Thank you.

• Cannot SSH in ASA after EZVPN configuration and do not specify "split-tunnel-political tunnelspecified.

  Even after the "split-tunnel-policy tunnelspecified" specification with "split-tunnel-network-list value TUNNEL of SPLITTING" and denying all traffic to the public IP address of the ASA, I'm still not able to SSH in the firewall. Everything else seems to work OK, but I have to be able to handle the ASA from the public interface. In fact, I expect little given the mean one sa is the installer for the tunnel, and it would seem that a deny statement would be ignored, but perhaps there is a way around this. Thank you.

  If you want to connect to your home IP through the tunnel, you must specify 'inside access management:

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/a...

  Best regards, Karsten

  Sent by Cisco Support technique iPad App

• Split tunnel with ASA 5510 and PIX506.

  Hello

  I have the production between Asa 5510 (main office) and Pix 506 VPN tunnel. It is configured so that all traffic is encrypted and moves through the tunnel. This includes remote users behind Pix Internet traffic. I would like to use split tunnel and direct Internet traffic hitting the web directly from Pix instead of going through the tunnel. How can I do this safely? Please see current config Pix below:

  :
  6.3 (5) PIX version
  interface ethernet0 car
  interface ethernet1 10baset
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100

  clock timezone EDT - 5
  clock to summer time EDT recurring 2 Sun Mar 2:00 1 Sun Nov 02:00
  No fixup protocol dns
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol they 389
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  No fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  no correction protocol tftp 69
  names of
  allow VPN 192.x.x.x 255.255.255.0 ip access list one
  LocalNet ip access list allow a whole
  pager lines 20
  opening of session
  monitor debug logging
  logging warnings put in buffered memory
  logging trap warnings
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside 24.x.x.x 255.255.255.0
  IP address inside192.x.x.x 255.255.255.0
  IP audit name Outside_Attack attack action alarm down reset
  IP audit name Outside_Recon info action alarm down reset
  interface IP outside the Outside_Recon check
  interface IP outside the Outside_Attack check
  alarm action IP verification of information
  reset the IP audit attack alarm drop action
  disable signing verification IP 2000
  disable signing verification IP 2001
  disable signing verification IP 2004
  disable signing verification IP 2005
  disable signing verification IP 2150
  PDM logging 100 information
  history of PDM activate
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0 access-list LocalNet
  Route outside 0.0.0.0 0.0.0.0 24.x.x.x
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set esp-3des esp-md5-hmac AMC
  map UrgentCare 10 ipsec-isakmp crypto
  card crypto UrgentCare 10 corresponds to the VPN address
  card crypto UrgentCare 10 set counterpart x.x.x.x
  card crypto UrgentCare 10 value transform-set AMC
  UrgentCare interface card crypto outside
  ISAKMP allows outside
  ISAKMP key * address x.x.x.x 255.255.255.255 netmask
  ISAKMP identity address
  part of pre authentication ISAKMP policy 20
  ISAKMP policy 20 3des encryption
  ISAKMP policy 20 md5 hash
  20 2 ISAKMP policy group
  ISAKMP duration strategy of life 20 86400
  SSH timeout 15
  Console timeout 0
  Terminal width 80
  Cryptochecksum:9701c306b05151471c437f29695ffdbd
  : end

  I would do something by changing the acl that applies to your crypto card. You want to know what you want to support above the tunnel and then deny other networks.

  If you have:

  192.168.3.0/24

  192.168.4.0/24

  10.10.10.0/24

  172.16.0.0/16

  Do something like:

  VPN access list allow 192.x.x.x ip 255.255.255.0 192.168.3.0 255.255.255.0

  VPN access list allow 192.x.x.x ip 255.255.255.0 192.168.4.0 255.255.255.0

  VPN access list allow 192.x.x.x ip 255.255.255.0 10.10.10.0 255.255.255.0

  VPN access list allow 192.x.x.x 255.255.255.0 ip 172.16.0.0 255.255.0.0

  Then when the traffic is destined for something other than these networks, it will go not to the ISP instead of the tunnel.

  HTH,

  John

• Split tunnel setup on asa 8.4 with 6.4 AMPS

  We have established and work, with the exception of tunneling split anyconnect.

  the 6.4 AMPS I went to: remote VPN access > (Client) network access > Group Policy > GroupPolicy_anyconnect_vpn > edit > advanced > split tunneling > then unchecked "inherit" on list of network and selected an ACL called "TUNNEL of SPLIT.

  the ACL is pasted below the CLI, it is all of our internal networks, everything is static routed and on the same vlan

  SG-ASA-1 # sho - TUNNEL of SPLITTING access list
  list of access TUNNEL of SPLITTING; 10 items; hash name: 0x25b1daf1
  Access-list 1 permit line SPLIT TUNNEL extended ip 192.168.100.0 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0xe3a9484b
  permit for SPLIT-TUNNEL list lengthened 2 ip 192.168.105.0 access line 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0x377afd96
  allowed for access list 3 SPLIT-TUNNEL line scope ip 192.168.110.0 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0x0b4d6f9c
  line 4 extended to the TUNNEL of SPLIT-ip access list 192.168.120.0 allow 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0x7a6cc93f
  allowed for access list 5 SPLIT-TUNNEL line scope ip 192.168.130.0 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0xe228bdad
  allowed for access list 6 SPLIT-TUNNEL line scope ip 192.168.140.0 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0x317f80c8
  allowed for access list 7 SPLIT-TUNNEL line scope ip 192.168.150.0 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0xe4c276b0
  allowed for access list 8 SPLIT-TUNNEL line scope ip 192.168.160.0 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0x0c2dd3ab
  allowed for access list 9 SPLIT-TUNNEL line scope ip 192.168.170.0 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0x00a4d4e3
  permit for line TUNNEL of SPLITTING access-list 10 scope ip 192.168.180.0 255.255.255.0 192.168.22.96 255.255.255.224 (hitcnt = 0) 0xfb381008
  SG-ASA-1 #.

  After this setting in the Group of ASSISTANT Deputy Ministers policy, we tested in vain yesterday morning. They can connect and ping all those inside network but not the internet. The journal of the asa showed what follows when a vpn client tried to ping Yao

  6 August 14, 2012 07:51:04 64.60.xxx.xxx 4397 206.169.203.226 1433 routing cannot locate the next hop for TCP to inside:64.60.xxx.xxx/4397 to outside:206.169.203.226/1433

  We can ping the inside no network problems after you connect to the VPN from outside.

  64.60.xxx.xxx is our public IP address that is on the external interface, which is the IP address we use to vpn.ourdomain.com

  Thanks in advance for any help

  Hello

  You can try to use the standard access list in the same menu.

  List of strategies for the tunnel CLCK spit > click on manage, select the standard acl tab and only add 192.168.0.0 255.255.0.0 (for testing purposes)

  Then test if it works to connect to Internet

  The filtering you want, highest in your message you can do it with a security acl.

  If it works, you can add more specific standard ACL split tunneling list, as

  Add 192.168.100.0

  etcetc

• What is is it possible to use the acl extended for split tunneling on ASA?

  I'm setting up VPN IPSEC RA on SAA and I would like to know if it is possible to use the ACL extended as part of the split tunneling?

  Thank you!

  Yes, you can use the extended ACL. See this example:http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-nex...

  Kind regards

  Averroès.

• How to match tunnel-group with auth ASA 8.2 and IPSec VPN Client using digital certificates with Microsoft CA

  Hello

  I set up a lab for RA VPN with a version of the ASA5510 8.2 and VPN Client 5 software using digital certificates with Microsoft CA on a Windows 2003 server. I did the configuration based on this document from Cisco's Web site:

  http://www.Cisco.com/en/us/partner/products/ps6120/products_configuration_example09186a0080930f21.shtml

  Now, the vpn works fine, but now I need to configure a tunnel-different groups so I can provide different services to different users. The problem I have now is that I don't know how to set it up for the certificate is the name of tunnel-group. If I do an ASA debug crypto isakmp I get this error message:

  % ASA-713906 7: IP = 165.98.139.12, trying to find the group through OR...
  % 3 ASA-713020: IP = 165.98.139.12, no group found by matching well payload ID: unknown
  % ASA-713906 7: IP = 165.98.139.12, trying to find the group via IKE ID...
  % 3 ASA-713020: IP = 165.98.139.12, no group found by matching well payload ID: unknown
  % ASA-713906 7: IP = 165.98.139.12, trying to find the group via IP ADDR...
  % ASA-713906 7: IP = 165.98.139.12, trying to find the group using default group...
  % ASA-713906 7: IP = 165.98.139.12, connection landed on tunnel_group DefaultRAGroup

  So, basically, when using certificates I connect always VPN RA only with the group default DefaultRAGroup. Do I have to use a model of different web registration for application for a certificate instead of the user model? How can I determine the OU on the user certificate so that match tunnel-group?

  Please help me!

  Kind regards

  Fernando Aguirre

  You can use the group certificate mapping feature to map to a specific group.

  This is the configuration for your reference guide:

  http://www.Cisco.com/en/us/partner/docs/security/ASA/asa82/configuration/guide/IKE.html#wp1053978

  And here is the command for "map of crypto ca certificate": reference

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/C5.html#wp2186685

  Hope that helps.

• EZVPN connection fails with the error "Split tunnel higher than max attributes...."

  Hello

  We have ASA 5520 acting as the VPN server and the router Cisco 1941 as EZVPN client. These last days of customer is not able to establish the vpn connection. 1941 continuous router generates the below the log messages

  ---------------

  001569: Jul 22 ABC 12:19:05.883: CRYPTO-4-EZVPN_SA_LIMIT %: EZVPN (VPNGROUP) Split tunnel attributes (51) greater than max allowed split attributes (50)

  001574: Jul 22 ABC 12:19:07.835: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = vpn_user group = VPNGROUP Client_public_addr = Server_public_addr =

  004943: Jul 22 ABC 11:32:42.247: % IP_VFR-4-FRAG_TABLE_OVERFLOW: Dialer1: the table fragment has reached its maximum 16

  ---------------

  Future prospects for aid and the suggestion of experts

  Thank you

  Israr Ahmad

  Yes, your split tunnel access-list is too big, and he has reached the maximum number of lines.

  Try to reduce the number of ACL for your tunnel of split ACL maybe combining the subnets if possible.

• Split Tunneling does not

  I'm working on an installation of the laboratory program at home with my X-5506, and I got a split tunneling configuration problem.  Every change I seem to give me internet access, gives me access to the local network or remove both.  The current configuration, I took them both and I am a little puzzled.  I have attached the configuration.  Any guidance would be greatly appreciated!

  Change:

  split-tunnel-policy excludespecified

  TO:

  split-tunnel-policy tunnelspecified

  I notice you are using 192.168.0.0/24. Make sure that you do not work VPN'ing an address 192.168.0.0/24 as well (or a subnet that is also identical to your subnet that you are trying to access remotely) or it won't work. Overall, you should avoid using 10.0.0.0/24 and 192.168.0.0/24 in production networks because they are so frequently used in home networks. I also note that you have configured IKEv2. IKEv2 does not support split tunneling. SO be sure you use only the AnyConnect client in SSL mode.

• Windows - Internet access, no split Tunnel L2TP VPN Clients does not

  Greetings!

  I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.

  I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.

  Here is the configuration:

  : Saved
  :
  ASA Version 1.0000 11
  !
  SGC hostname
  domain somewhere.com
  names of
  COMMENTS COMMENTS LAN 192.168.2.0 name description
  name 75.185.129.13 description of SGC - external INTERNAL ASA
  name 172.22.0.0 description of SITE1-LAN Ohio management network
  description of SITE2-LAN name 172.23.0.0 Lake Club Network
  name 172.24.0.0 description of training3-LAN network Southwood
  description of training3 - ASA 123.234.8.124 ASA Southwoods name
  INTERNAL name 192.168.10.0 network Local INTERNAL description
  description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
  description of Apollo name 192.168.10.4 INTERNAL domain controller
  description of DHD name 192.168.10.2 Access Point #1
  description of GDO name 192.168.10.3 Access Point #2
  description of Odyssey name 192.168.10.5 INTERNAL Test Server
  CMS internal description INTERNAL ASA name 192.168.10.1
  name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
  description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
  description of training3-VOICE name Southwood Voice Network 10.1.0.0
  name 172.25.0.0 description of training3-WIFI wireless Southwood
  !
  interface Vlan1
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Vlan2
  nameif INSIDE
  security-level 100
  255.255.255.0 SGC-internal IP address
  !
  interface Vlan3
  nameif COMMENTS
  security-level 50
  IP 192.168.2.1 255.255.255.0
  !
  interface Ethernet0/0
  Time Warner Cable description
  !
  interface Ethernet0/1
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/2
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/3
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/4
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/5
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/6
  Description for Wireless AP Trunk Port
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/7
  Description for Wireless AP Trunk Port
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  boot system Disk0: / asa821-11 - k8.bin
  Disk0: / config.txt boot configuration
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS domain-lookup outside
  INTERNAL DNS domain-lookup
  DNS domain-lookup GUEST
  DNS server-group DefaultDNS
  Name-Server 4.2.2.2
  domain somewhere.com
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  DM_INLINE_TCP_1 tcp service object-group
  EQ port 3389 object
  port-object eq www
  EQ object of the https port
  EQ smtp port object
  the DM_INLINE_NETWORK_1 object-group network
  network-object SITE1-LAN 255.255.0.0
  network-object SITE2-LAN 255.255.0.0
  network-object training3-LAN 255.255.0.0
  object-group training3-GLOBAL network
  Southwood description Global Network
  network-object training3-LAN 255.255.0.0
  network-object training3-VOICE 255.255.0.0
  network-object training3-WIFI 255.255.0.0
  DM_INLINE_TCP_2 tcp service object-group
  EQ port 5900 object
  EQ object Port 5901
  object-group network INTERNAL GLOBAL
  Description Global INTERNAL Network
  network-object INTERNAL 255.255.255.0
  network-object INTERNALLY-VPN 255.255.255.0
  access-list outside_access note Pings allow
  outside_access list extended access permit icmp any CMS-external host
  access-list outside_access note that VNC for Camille
  outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
  access-list outside_access note INTERNAL Services
  outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
  DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
  access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
  access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
  access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
  access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
  access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
  access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
  access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
  no pager
  Enable logging
  exploitation forest asdm warnings
  Debugging trace record
  Outside 1500 MTU
  MTU 1500 INTERNAL
  MTU 1500 COMMENTS
  192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 623.bin
  enable ASDM history
  ARP timeout 14400
  Global 1 interface (outside)
  (INTERNAL) NAT 0 access-list sheep
  NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
  NAT (GUEST) 1 0.0.0.0 0.0.0.0
  5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
  3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
  public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
  public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
  public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
  5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
  Access-group outside_access in interface outside
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  RADIUS protocol AAA-server Apollo
  Apollo (INTERNAL) AAA-server Apollo
  Timeout 5
  key *.
  AAA authentication enable LOCAL console
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  Enable http server
  http 0.0.0.0 0.0.0.0 INTERNAL
  http 0.0.0.0 0.0.0.0 COMMENTS
  No snmp server location
  No snmp Server contact
  Community SNMP-server
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
  Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
  correspondence address 1 card crypto outside_map INTERNAL SITE1
  card crypto outside_map 1 set of peer SITE1 - ASA
  card crypto outside_map 1 set of transformation-ESP-3DES-SHA
  address for correspondence card crypto outside_map 2 INTERNAL training3
  outside_map 2 peer training3 - ASA crypto card game
  card crypto outside_map 2 game of transformation-ESP-3DES-SHA
  address for correspondence outside_map 3 card crypto INTERNAL SITE2
  game card crypto outside_map 3 peers SITE2 - ASA
  card crypto outside_map 3 game of transformation-ESP-3DES-SHA
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  delimiter group @.
  Telnet training3 - ASA 255.255.255.255 outside
  Telnet SITE2 - ASA 255.255.255.255 outside
  Telnet SITE1 - ASA 255.255.255.255 outside
  Telnet 0.0.0.0 0.0.0.0 INTERNAL
  Telnet 0.0.0.0 0.0.0.0 COMMENTS
  Telnet timeout 60
  SSH enable ibou
  SSH training3 - ASA 255.255.255.255 outside
  SSH SITE2 - ASA 255.255.255.255 outside
  SSH SITE1 - ASA 255.255.255.255 outside
  SSH 0.0.0.0 0.0.0.0 INTERNAL
  SSH 0.0.0.0 0.0.0.0 COMMENTS
  SSH timeout 60
  Console timeout 0
  access to the INTERNAL administration
  Hello to tunnel L2TP 100
  interface ID client DHCP-client to the outside
  dhcpd dns 4.2.2.1 4.2.2.2
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  !
  address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
  dhcpd Apollo Odyssey interface INTERNAL dns
  dhcpd somewhere.com domain INTERNAL interface
  interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
  enable dhcpd INTERNAL
  !
  dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
  dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
  enable dhcpd COMMENTS
  !

  a basic threat threat detection
  statistical threat detection port
  Statistical threat detection Protocol
  Statistics-list of access threat detection
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  NTP server 192.43.244.18 prefer external source
  WebVPN
  allow outside
  CSD image disk0:/securedesktop-asa-3.4.2048.pkg
  SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
  SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
  enable SVC
  Group Policy DefaultRAGroup INTERNAL
  attributes of Group Policy DefaultRAGroup
  Server DNS 192.168.10.4 value
  Protocol-tunnel-VPN l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com
  Group Policy DefaultWEBVPNGroup INTERNAL
  attributes of Group Policy DefaultWEBVPNGroup
  VPN-tunnel-Protocol webvpn
  Group Policy DefaultL2LGroup INTERNAL
  attributes of Group Policy DefaultL2LGroup
  Protocol-tunnel-VPN IPSec l2tp ipsec
  Group Policy DefaultACVPNGroup INTERNAL
  attributes of Group Policy DefaultACVPNGroup
  VPN-tunnel-Protocol svc
  attributes of Group Policy DfltGrpPolicy
  value of 192.168.10.4 DNS Server 4.2.2.2
  VPN - 25 simultaneous connections
  VPN-idle-timeout no
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com
  the value INTERNAL VPN address pools
  chip-removal-disconnect disable card
  WebVPN
  SVC keepalive no
  client of dpd-interval SVC no
  dpd-interval SVC bridge no
  value of customization DfltCustomization
  attributes global-tunnel-group DefaultRAGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultRAGroup
  IPSec-attributes tunnel-group DefaultRAGroup
  pre-shared-key *.
  Disable ISAKMP keepalive
  tunnel-group DefaultRAGroup ppp-attributes
  No chap authentication
  no authentication ms-chap-v1
  ms-chap-v2 authentication
  attributes global-tunnel-group DefaultWEBVPNGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultWEBVPNGroup
  tunnel-group 123.234.8.60 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.60
  pre-shared-key *.
  tunnel-group 123.234.8.124 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.124
  pre-shared-key *.
  tunnel-group 123.234.8.189 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.189
  pre-shared-key *.
  type tunnel-group DefaultACVPNGroup remote access
  attributes global-tunnel-group DefaultACVPNGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultACVPNGroup
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the http
  inspect the they
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
  : end
  ASDM image disk0: / asdm - 623.bin
  ASDM location Camille 255.255.255.255 INTERNAL
  ASDM location INTERNAL CGT-external 255.255.255.255
  ASDM location INTERNAL SITE1-LAN 255.255.0.0
  ASDM location INTERNAL SITE2-LAN 255.255.0.0
  ASDM location INTERNAL training3-LAN 255.255.0.0
  ASDM location INTERNAL training3 - ASA 255.255.255.255
  ASDM location INTERNAL GDO 255.255.255.255
  ASDM location INTERNAL SITE1 - ASA 255.255.255.255
  ASDM location INTERNAL SITE2 - ASA 255.255.255.255
  ASDM location INTERNAL training3-VOICE 255.255.0.0
  ASDM location puppy 255.255.255.255 INTERNAL
  enable ASDM history

  I should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.

  You must configure * intercept-dhcp enable * in your group strategy:

  attributes of Group Policy DefaultRAGroup

  attributes of Group Policy DefaultRAGroup

  Server DNS 192.168.10.4 value
  Protocol-tunnel-VPN l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com

  Intercept-dhcp enable

  -Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked.  It is located on the Advanced tab of VPN client TCP/IP properties.   Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.

  Alex

• No split tunnel-access internet via isa in dmz

  Hello

  I have configured my asa 5520 v 7.2 for remote VPN. Its works fine. I need to provide my customer internet access without activating split tunnel. I went through a few example below of a doc:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00805734ae.shtml

  the preceding is not enough more me like one have different needs

  I want my client VPN to ASA and access to internet, I had ISA connected to the VPN device. All my vpn clients want access to the internet, it must use this operation to access the internet. My ISA server is in the same subnet of the VPN device by using a different gw for internet access.

  Pls comment

  Add the below: -.

  attributes of the strategy of group staffvpn

  use a MSIE-proxy-server method

  Internet Explorer-proxy server value x.x.x.x

  Disable Internet Explorer-proxy local-bypass

  attributes of the strategy of group staffvpn

  use a MSIE-proxy-server method

  Internet Explorer-proxy server value x.x.x.x

  Disable Internet Explorer-proxy local-bypass

  attributes of the strategy of group newstaffvpn

  use a MSIE-proxy-server method

  Internet Explorer-proxy server value x.x.x.x

  Disable Internet Explorer-proxy local-bypass

  adel username attributes

  use a MSIE-proxy-server method

  Internet Explorer-proxy server value x.x.x.x

  Disable Internet Explorer-proxy local-bypass

  username weppe attributes

  use a MSIE-proxy-server method

  Internet Explorer-proxy server value x.x.x.x

  Disable Internet Explorer-proxy local-bypass

  Remote VPN group no matter what you want to test with. where x.x.x.x is the IP address of the ISA server computer.

  HTH.