Wireless - connection Portege 4010 problem

Similar Questions

• The Portege 4010 problems

  I recently bought a refurbished Portege 4010 and it works fine, except that pips sound a lot. It seems to be random, may occur as once in 3-4 seconds, or it may seem fine for a few minutes then * glitch glitch glitch *. Looks like the tempo of the sound is slowed and then catch upwards, and it sometimes makes a noise dry sound.

  I have a Portege 4000, which did explode a little sound each time than in quite awhile, but he appeared rarely as once every 30 minutes and was barely noticeable. On this 4010, it's much worse.

  I have all the Toshiba official drivers, running a twisted installation of XP SP2. I tried a clean install and the sound has the same faults.

  Right now I use ULi drivers I found on the Nvidia download page, they have helped a bit, the sound bugs are now more sporadically, but when they occur (once every two minutes or more), they are always as bad as they were at the start. Also, ULi drivers are sound drivers only I could find that have sufficient volume levels, with the drivers found on your site the wave volume distorts when turned over 20-25%, now I don't have to worry about that while she prepares to max as do some games, the sound will not be distorted. I had the same problem on my old Portege 4000, at the time I did not know the difficulty pilots and used a volume reduction program to force 'bad' apps and games to mix parameters.

  The 4010 is such a portable grand, when you use a second battery, he gets the same battery life of 5 hours of the 4000 and with more processing power. It's a shame that something minor like a sound chip of ruins all the fun. Yes, I know it's pretty old, but as long as he does his job, which is no big deal.

  So is there any fix I can try? Thanks in advance.

  Good job!

• Keyboard on my Portege 4010 problems

  Out of the blue, I have keyboard problems on my portege 4010. I have bad start up and now that I have, I can't access some of the problems, the keys get stuck, funny noises... beeps all the symptoms of a questionable keyboard. What I can do, otherwise, buy a replacement keyboard (v.expensive) or use an external keyboard?

  I personally have not dropped something on the keyboard, so problems can just be from one day to the next, or should interogate my husband.

  Hello

  Maybe your husband has changed something? ;)
  But seriously, if you have some problems with the boot and keyboard in my opinion, you should try to pick you up BONES. If the malfunction of the same images I recommend to contact the ASP for more information.

  Good bye

• Sound on Portege 4010 problems

  Hello

  I am the proud owner of a Toshiba Portege 4010, but the only problem that I couldn't solve is the sound.

  The problem occurs when I use MP3 reading program (Winamp / TRAKTOR DJ). Music moves for a very short period of time, perhaps some 20 milliseconds every 1 to 2 minutes (on a random date).

  I tried to change each buffer option in my mp3 with no result reading programs.
  I am running Windows XP Service Pack 2 with all drivers installed on the Toshiba site (including the Windows XP audio driver)

  The problem does not disappear if the laptop works plugged (best performance of the processor).

  If someone has encountered this problem and knows the solution, I would really appreciate it.
  I use this laptop for playing background music (I am a DJ).

  Best regards
  Mircea Bartic

  Hi Mircea

  It is not easy to say what may be the problem. If I understood you right this would happen only if the laptop is running on battery. Am I wrong?

  I assume that the processor or HARD drive maybe activity interrupts the music. Please try checking activity (Performance) CPU settings in the tool under the profile that is used if the device is running on battery.

  It is also possible that some applications (program antivir) forced the HARD drive activity. Please check all these aspects.

• Satellite P100-434: wireless connection with Vista problem

  Just bought this laptop with Vista and so far could not get the wireless to connect, I have 3 other computers and they will all connect, I have reset the router and set up new accounts on other computers without problem, but unable to do it on the P100.

  I tried the new RADAR feature and will not pick up all the networks, but by trying to establish a new connection it shows that a wireless network is available but it is nameless, although my network is named, I took the passkey of the network so that it is open but still does not connect, LAN via ethernet fine work.

  Wireless switch is on, but when I drag off switching wireless says WE

  Hello

  I can't give you an exactly the answer why you cannot connect to your WLan with Vista because there are so many options that should be checked.
  But I think that you will find the solution yourself with a little help from the Microsoft Web site.

  Please see this site:
  Connect to a network with Windows Vista wireless
  http://www.Microsoft.com/technet/community/columns/cableguy/cg0406.mspx

  You will find many useful tips, screenshots and Tips how to connect to WiFi with Vista.

  Please post again if you have found the key

• I have windows 7 and how to remedy a wireless connectivity problem when it; s a problem when it has detected the wireless adapter or access point

  I have windows 7 How to deal with a problem of wireless connectivity. The problem according to the diagnosis of computer's wireless adapter or access which was detected point

  You have McAfee? McAfee has been updated at the same time as the last batch of updates from Windows 7 and this is the cause of problems of internet connection for most, if not all, users of McAfee.

  See the communication from this "criticism" - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary. There are corresponding communications for their enterprise products.

  I had to run the removal of McAfee Development tool a few times before and it caused a problem with the license if the PC was not connected to the internet during the abduction. Due cat of McAfee support reset their files in order to allow the relocation-reactivation. Here is their link cat - McAfee - media contains the link to the cat

• Portege 4000 - Installed W2K - wireless connection problem

  I installed W2K the Portege 4000. XP was too heavy a resource for this system.

  After you install the network driver wireless Cisco (3.5.13.0) of your Web site, I am unable to get a wireless connection. In XP this comes automatically with an icon. The network device switch that I also installed did not help.

  I have the following:

  Connection to the local network - ethernet

  2 - wireless LAN connection

  Although LAKE 2 is activated this still does not pick up wireless.

  Any ideas?

  Hello

  PUH Windows 2000 is an older system. I didn t forget not all parameters of WLan connection and so I googled a bit.

  and I found an interesting page and a brief description how to configure Wlan connection in W2k.

  Check this box:
  http://www.Yorktech.com/wireless/windows2000/configureW2k.htm

  Welcome them

• Wireless connection on Portege R100

  I have a couple of portege R100. When you connect to my domain, using the wireless connection, the logon scripts fail to run the first time. If you log out, then log in again, the script will run without problem. Y at - it a fix for this problem?

  Hello

  Unfortunately have no proper explanation, but I guess that WLAN cannot be connected so fast that LAN and it may be the reason why the first logon fails. In my opinion it has nothing to do with the functionality of the device and this is just a feature of network.

  Maybe some WLAN expert can give you a good explanation.

  Good luck!

• Portege 4010 Bluetooth - connection for samsung and motorola phones probs

  I have a portege 4010 with bluetooth. I am trying to connect to our two phones - a samsung sgh-e370 (newish) and a motorola V600 (2 years). Both have BT I downloaded and installed the latest Tosh BT stack (4.0.something). Shows Device Manager four drivers of tosh in BT - all are OK. I have allowed the discovery and allow the connection on the tosh. I did the same thing on the phones. When I run the "Add new connection" Wizard on tosh, he finds two phones and they appear under the devices section in BT Manager with the names I gave them on real phones. However, neither picked up phone tosh and showed no tosh by asking the numbers of pins on the phones.

  The net result is I now two phones display in BT Manager, but if I click on is and choose use log I recover the error "connection failed".

  If I try to find the portege using the phone, the samsung it is but motorola doesn't have. I can't get the motorola to twin with the tosh - it just says "unable to pair up with the portege.

  Any help gratefully received.

  RJ

  Hello

  I don't really know what is the problem in your case, but I did this a few times with my Motorola RAZR V3 and it works fantastic. The whole was finished for 1 minute. I hope that you do it in the right order, but I am writing to you the steps I did:

  1 activate the Bluetooth using the FN + F8 key combination
  2. install the new hardware if necessary (some of them)
  3. start the Bluetooth stack
  4 turn on the Bluetooth on the mobile phone (discoverable)

  5. Select the Express mode > next
  6. choose visible device listed in 'Bluetooth device list' > next
  7 choose to identify passkey (1234)
  8. Enter the key in the mobile phone. Twinning will be success

  I did it on this path, and now I can send all documents in my Tecra. If you want to use as a modem, you must do this:

  1. after peeling going on Next and configure the internet connection
  (provider number) > finish
  2. the new connection will be created in the Bluetooth stack utility
  3. you can start the numbering with double click or click with the right button of the mouse and choose 'connect '.

• U940 PSU6VA satellite - wireless connectivity problems

  _ * My specifications: * _
  * Model: * Toshiba Ultrabook (Satellite PSU6VA - 00S 002 U940)
  * Operating system: * Windows 8.1 x 64 (upgrade of Windows 8 x 64)
  * Wireless adapter: * Intel Centrino Wireless - N 2200
  * Wireless adapter driver version: * 15.10.0.12 (which is the last for my device)

  I got this Ultrabook since February 2013, and throughout this period, I always had problems with wireless connectivity, even after a factory reset. My wireless icon varies between three States:
  * Internet access
  * Limited (in which case I can't connect to the internet or any other device on the network)
  * Not connected - connections are available (and if I try to connect to the network, it will fail)

  Sometimes my computer would instantly reach the State of "Internet access" at startup and remain in this State. Other times, it would be 'limited' for several minutes after the start of my computer before it finally connected, and even in this case, the connection will drop out every now and then. In the worst case, it would indefinitely remain "Limited" or "not connected", regardless of how many times I reset my adapter wireless or rebooted my computer.

  Until very recently, I always thought that these problems have occurred randomly. However, I noticed recently that I have always a connection perfect, whenever there is no other computers connected wirelessly to my router, and I always have problems more or less when there is at least another computer (or even a smart phone) connected wireless to the router. If there is another computer connected to the router via an Ethernet cable, this causes no problems. It's only wireless connections that interfere with my computer.

  It is only this computer that has these problems; the other computers in my house ever experience these issues, no matter how many computers is online. In addition, my computer is not only these problems with my home router; It has the same problems on the network wireless at my University.

  My question is, how do I fix? Is this a known bug or is my defective wireless adapter? I know that I can connect using an Ethernet cable if possible (I have never problems with Ethernet connections), but this is not always possible at the University.

  Did you remove the old driver Win 8 Intel of the system before you upgrade to version 8.1 to win?
  The old Wlan Intel driver could affect the performance of a Wi - Fi connection.

  The driver update page Win 8.1 says clearly that Intel Wlan driver must be uninstalled and the
  Inbox Windows 8.1 version must be used.
  http://support.Toshiba-tie.co.jp/windows81/drivers/PSU6V_Up_au.htm

• Resolved - problem of wireless connectivity "wlan0 link is down.

  Quick update:

  * If you encounter this message, make sure that you are trying to connect to a wireless "N".

  Yes, he is in small print on the box, right, sony will not ask you this when you are troubleshooting.

  * If you rely on Sony for smart assistance, forgetabout it.

  * After the receiver a comment card and to express my disappointment, the call center outsource sent a letter... and when I called to discuss, they were still clueless.

  Sorry, but the support structure is absolutely catastrophic.

  We now return you to your regular programming...

  ----------------------------------------------------------------

  OK, let's go, in detail:

  My Sony dashboard came again, out of the box today. It will connect to my network.

  FYI: My set of skills: I am an engineer of sales network, with an extensive network of Wi - Fi and running in my house.

  After connecting the dashboard and providing configuration information, the message I get is:
  __________________________________________________

  Network configuration
  Failed network connection...

  wlan0 link is down
  did not get an IP address
  Internet is inaccessible
  __________________________________________________

  Like others on this forum, it seems that my dashboard won't "handshake" with my wireless router.

  To try to solve problems, I did the following:

  (Slot 0): both my wireless router and my attempt to connect to the sony dashboard are in my home office, so the intensity of the signal should not be a problem.

  (1) check the connectivity wireless on a multitude of home devices: laptop, TV, iPhone, ipad... in short: Wireless works. Both with fixed IP and distributed DHCP address.

  (2) restart my Rosewill RNX - N4, wireless "N".

  (3) allow my SSID be visible (that I found which helped my LG TV to connect during its initial configuration)

  (4) checked my WLAN settings on my router:

  SSID: *.
  Security mode: WPA2 only: personal
  Type of encryption: AES
  Pre-shared Key: v * m

  (5) restarted the dashboard of Sony.

  (6) wireless seems to work on the sony dash, as the configuration screen of the network about dashboard States:
  ______________________________________________

  Network configuration
  Choose a wireless connection

  ..:| (my ssid is displayed)

  MAC address: (my MAC address of my wireless router is displayed)
  ______________________________________________

  (7) I select my SSID (FYI: nobody else displayed) and click (next)

  (8) place comes the next screen:
  ______________________________________________
  Network configuration
  Choose the key to coding (WPA2-PSK)

  HEX)
  (o) ASCII
  ______________________________________________

  I select ASCII then (Next)

  (9) he asked my key, I carefully enter (.. .slightly annoyed that the screen will not edge to allow me to see all the characters that I'm going home)..., then click on (Next)

  (10) I choose Auto IP, as during the initial setup I keep it as simple as possible... and then hit (Next)

  (11) to the top displays the following screen:
  ______________________________________________
  Network configuration
  Confirm settings

  name: (my SSID) (My MAC Address)
  AUTH: WPA2PSK encryption: AES
  key: (poster in my correct key, read and validated twice)
  automatic IP allocation (DHCP)
  _____________________________________________

  Completely satisfied with it, I select (Next)

  (12) the sony dashboard begins its Network Configuration / connection looking for the network and then...

  (13) the following:
  __________________________________________________

  Network configuration
  Failed network connection...

  wlan0 link is down
  did not get an IP address
  Internet is inaccessible
  __________________________________________________

  (14) in an attempt to solve the problems, I also tried to set up with a static IP address:

  static IP address:
  IP: 192.168.15.20
  Subnet mask: 255.255.255.0
  Gateway: 192.168.15.1
  DNS1: 192.168.15.1
  DNS2: 8.8.8.8

  ... and the results were the same: "wlan0 link is down.

  (15) as a final step, I reset my wireless router to have no. SECURITY at ALL. Guess what? "wlan0 link is down.

  At this point, I'm at a loss for what I could do "evil".

  I welcome comments from other users, either to continue to solve the problem or sharing what you did to resolve your issue with connectivity.

  Thank you.

  c.

  Well, here I am, a moth and a half later.

  After speaking to Sony technical support...

  After sending the camera back to Sony...

  After having been informed by Sony that this point had problems, they need to replace parts, AND they were going to send me a new device to save time...

  I get a new, and it has exactly the same features / problem.

  So I try another router, same problem.

  Guess why?

  Because I have my network running "N" and it's a Sony wireless B/G device.

  Anyone who has mentioned in technical support... The point on the replacement due to damaged items was total BS.

  If you have a network of "N", it will recognize your SSID and even to recognize the security there.

  But it does not connect.

  Once I changed to a mixed G/N wireless environment, it connects.

  For example, you might say my own question... should have known.

  However, Sony sells a device "B/G" when almost everything comes standard "N"...

  Not cool, Sony... Not cool.

• Problem with wireless connection with Satellite U500

  Hello
  Three months ago, I bought a Toshiba laptop Satellite U-500 (Windows Vista). I have a problem with the wireless connection - sometimes, it does not work and I have to restart pressing F8 and repair, then the connection is re-established; If I put into hibernation the connection is intact, but after a stop the problem maybe redo surface after the 2nd or 3rd session.

  I tried to format it, but it worked only for a while. The 2nd item in network adapters in the device (Realtek RTL8192E Wireless LAN 802.11n PCI-E NIC) Manager shows a yellow exclamation point. The message is this:
  "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)
  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  Could you please help. I have sky broadband and am currently connected via the ethernet cable.

  Thank you
  Fauzan

  For 32-bit Vista go here [http://uk.computers.toshiba-europe.com/innovation/vista_drivers.jsp?macId=&LNG=1&mode=allMachines&us erOS = & action = search & SelCategorie = 2 & selFamily = 2 & salts Eries = 198 & selProduct = 855 & selShortMod = 1 & selOS = 26 & selType = all & country = 8 & language = 13 & searc h =] and download and then run the wireless LAN driver. That should clear the «!» If it isn't you can also find the vista driver at [http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=9&PFid=9&Level=6& Conn = 5 & DownTypeID = 3 & GetDown = false & downloads = true #R TL8192E]

• R7000, problems with wireless connection after the last firmware update 1.0.6

  I recently updated to the latest firmware available for the R7000...

  The upgrade went well and my Wired PC all connected without any problem, but several of my wireless devices were unable to connect to the WiFi. I have my cell phone Wifi (Android phone) kept gives me an error of authentication, but was able to connect to the network comments... weird...

  I started firmware 1.0.4 and everything worked well again... it seems that the new firmware is buggy.

  The Firmware versions listed above are only for the first three issues, to save typing, but you get the version that I use...

  Nick

  Hello

  I would like to let you know, I've improved in 1.0.6 last night and everything worked. The difference is this time I had to reset my router to the factory settings using the reset hidden at the back button and hold the button for about 7-10 seconds. This resets the router to the factory settings. I then had to re-enter all my IP address reservations and the word block list, but all my wireless devices were able to connect. The last time I did the upgrade, I just restarted the router, and I had read that I had to do a factory reset to operate correctly.

  It would have been nice for Netgear arrive at a way to extract Information form my version last-place back... it would have saved me a lot of time...

  Good luck

• Problems of sudden wireless connectivity with Qosmio G10

  I had a Qosmio G10 for almost 3 years now, and at least WRT my wireless connection, everything was fine until a few weeks ago.

  Little by little I started to lose the ability to connect to a WLAN after getting out of the mode standby (Win XP MCE): the computer wouldn't connect to my WIFI and would keep erratic jumps among the various wireless networks available in the neighborhood, without connect because they are all fixed.

  Initially, the problem could be solved by restarting the computer and the router.

  Now even that no longer works. I see either all local wireless networks, including mine, without being able to connect, or I see no WLAN at all.

  Windows status bar icons both ConfigFree show the small red cross and the system didn't budge. When I see available wireless networks, I'm trying to connect to my own, but then the computer attempts to connect forever. If I order for Toshiba ConfigFree * _For unchecking the checkbox in the properties window_ wireless * and I'm trying to connect manually my WLAN to the computer by dragging a link the said application to another provider program is in control.

  I have tried everything that came to my mind, the repair connection, enable/disable WZC, install new drivers for the Intel 2200BG, install the new version of ConfigFree... There is obviously some kind of conflict, but I do not understand what it can be.

  I don't know what else to do before decide to reinstall new Windows (oh dear oh dear). Moreover, my ADSL Modem/Router is always the same. The link has been dealt with by WPA/TKIP. Everything works fine with the other 2 computers and a phone with WiFi.

  Said by the way and quite surprisingly, a member of the family in another country began just having exactly the same problem on a Toshiba Satellite A110. In this case, the cause may be associated with the change of a Philips to a Linksys modem/router (either DHCP;) WPA/TKIP unchanged; everything works with another laptop in the same household)

  Can someone please help?

  Why use the CnfigFree tool to connect to the WLan?
  According to your message, you are using the Intel card.
  I would recommend so either use the Intel ProSet WLan client configuration tool or the clean option of Windows!

  > try to manually connect my WLAN to the computer by dragging a link the said application to another provider program is in control
  I assume that this error message is displayed because the ConfigFree is always chosen as tool to configure the WiFi network.

  However, the new installation of the OS may not be bad idea due to the fact that everything would be set up again.

• g505s 8.1 updates & wireless connection problem

  I just downloaded updates Microsoft last night and as soon as I restarted, my wireless connection was gone/missing/non-functional. I have read some other posts that made me think that the issue may be with the (Qualcomm Atheros AR956x) wireless network adapter driver, but the download or install the latest driver from Lenovo (wlan149w81) support site didn't do me good. I do not see again for a Wi - Fi connection in the center of network & sharing.

  Someone at - he never saw something like this before / know what might be causing the problem?

  Hi solid Cruver - thanks for the help. Looks like that the combo of what I did and what you recommended has done. Update the driver LAN first and second WLAN driver seems to have solved the problem. Thanks again.