CUCM 8.6 Multipoint calls to endpoints of TP

Similar Questions

• Calls from endpoints not registered in VCS

  I have a deployment with a VCS, and registered and unregistered endpoints. In this scenario, endpoints is not registered can not make calls to endpoints. The journal in the vcs is:

  * Search (68)
  *
  o status: complete
  *
  found o: false
  *
  o cause: not found
  *
  o Type: H323 (Setup)
  *
  o number of CallSerial:
  *
  o the tag:
  *
  o StartTime: time not set
  *
  o time: 0.01
  *
  o Source (1)
  o
  + Authenticated: false
  o
  + Area (1)
  +
  # Name: DefaultZone
  +
  # Type: default
  *
  o Destination (1)
  o
  + Alias (1)
  +
  # Type: IPAddress
  +
  # Origin: unknown
  +
  # Value: 10.94.151.63
  *
  o SubSearch (1)
  o
  + Type: transforms
  o
  + Action: Unprocessed
  o
  + ResultAlias (1)
  +
  # Type: IPAddress
  +
  # Origin: unknown
  +
  # Value: 10.94.151.63
  o
  + SubSearch (1)
  +
  # Type: Admin policy
  +
  # Action: Proxy
  +
  # ResultAlias (1)
  #
  * Type: IPAddress
  #
  * Origin: unknown
  #
  * Value: 10.94.151.63
  +
  # SubSearch (1)
  #
  * Type: FindMe
  #
  * Action: Proxy
  #
  * ResultAlias (1)
  *
  o Type: IPAddress
  *
  o origin: unknown
  *
  o value: 10.94.151.63
  #
  * SubSearch (1)
  *
  o Type: search rules
  *
  o CallsToUnknownIPAddresses (1)
  o
  + Mode: Direct
  o
  + Found: false

  "TVCS: event ="Call rejected"Service ="H323"Src - ip ="10.94.152.63"Src-port ="2254"Dst - ip ="10.94.151.63"call serial number ' Tag = '6' Protocol ="TCP"code-response ="Not found"level = '1' elements UTCTime ="2011-12-14 16:33:39, 862"

  I think that the problem is related with the zones, can someone help me?

  Thank you

  Hello

  Have you tried to set up a rule to search for AnyIPAddress? I just tested and without one I get the same problem as you, but if you set a search as follows rule, it works;

  Source: no

  Mode: AnyIPAddress

  On correspondence: continue

  Target area: localZone.GetDaylightChanges

  Otherwise, it seems when your end point registered receives the ARQ and sends Setup for Vcs to verify that if itcan set up the call he will not be able to find an applicable search rule.

  Martin.

  Sent by Cisco Support technique iPad App

• CUCM manipulation of VCS call

  Hello together,

  We have a little problem with our VCS + CUCM enviroment. When users of CUCM number users of VCS the URI that appears on the endpoint VCS is currently as "[email protected]" / * /-IP '. " But we want it to be displayed as "[email protected] / * /'." "

  Is that it is advisable to do this? I tried already with the CPL on VCS - C file, but it won't work.

  "I tried different versions of"[email protected] / * / ">" but will not change the source.

  This problem exists also for outgoing via VCS - E as endpoint outside our platform TP the CUCM-IP is also displayed and the user cannot remember history.

  Kind regards

  Jannik

  What version do you use? For SIP profiles assigned to endpoints, there is a setting I here to "Use full domain name" during the delivery. Please check. You have a directory URI assigned to the endpoint?

• Calls disconnected endpoint

  I had a client ask about the following situation.

  They have disconnected a C Series codec in one of their rooms. When calls were made to the endpoint offline, rather than fault, he ended up in the MCU. I don't have the means of laboratory to try to recreate it, but can someone shed some light on why this happens?

  Thank you

  Robert

  Hi Rob - your client to make a call to the E164 Alias of the system and then it routed to the MCU?  Could be the E164 alias is close or is the service prefix MCU and sound recorded as GW at any GK your help.  Would be useful to see if there is a correlation between the two, or if your client made up [email protected] / * /, and the alias is always nearby the GW service prefix.  This can also occur as well.

  It would be able to verify?

• CUCM mcu siptrunk video call bindwith

  Hi team

  I have a question about how can I config the bindwith for the siptrunk?

  I used a tunk sip to leave the cucm forward the video to the mcu conference call (5310), but no matter how I set up the bindwith video of location in cucm profile, call rates transmit only 384 k, but the receive call rate is 4000 k, but the hit rate and resolution are well when the mcu call codec (C60) directly by using H.323.

  I think I missed something in cucm configuration.

  Hi Jason,

  Could you give more information about the configuration of CUCM? How your regions are configured? Do you have the regions applied to SIP Trunk and the phone? The relationship between the regions allow enough bandwidth for the video?

  If I'm not mistaken, the default bandwidth for the video within the region setting is 384 k. Did you change this value to your regions?

  I also suggest to examine the configuration of your location and check if there is any restrictions applied.

  Concerning

  Paulo Souza

  Please note the answers and mark it as "answered" as appropriate.

• CUCM Upgrades vMotion of call center 24/7 production cluster (multiple) laboratory

  Hey everybody,

  I'm looking for documents that would support a Production Call Manager Cluster upgrade is done in the laboratory.  We did this for cuic, where we clone the Production VM and vMotion for a different Blade (dead net) and make the upgrades during the day, because there is no impact, then vMotion, their return to Production during a window of failure and turn them up after the turn down of the current production those.

  A couple of our clusters with 24/7 call centers, we wanted to limit the amount of time, they do not have some services, such as the mobility of the Extension. It is something that I have recommended, but I need of documentation or even a case of TAC for support to demonstrate management, since it is very different from our current MOP to make the upgrades.

  Thank you

  Randy

  The only caveats that is there is listed in this document only if you click on the hyperlink of VMware vMotion. If you follow them, then there is of course no problem, however you can always open a proactive TAC folder and get this done under their supervision/management, as long as you have a contract of ISV1 which I think is important to VMWare support not bound.

  If you have any doubts and want to go a way the recommended and most reliable compared to the then simply do vMotion using the DRS mechanism which is Cisco preferred for such things. Simply make a backup of DRS of your existing CM clusters running in production, create virtual machines using the same details such as the IP address, host name, NTP etc in his laboratory on a secluded environment and complete the restore of the DRS then and do what you want on the upgrade plan , etc.leaving tests the intact production servers. Once you upgrade and test had been made successfully in the laboratory, simply choose a Cup date more bring the server down production and move from laboratory to production.

  Concerning

  Deepak

• BAT to CUCM release 4.1 call forward

  I'm working on an old 4.1 CUCM and I need to use BAT to update the settings forward on several lines.  I really don't want to do this one by one.  However, I need to pass line one line two, which is the same extension, but in different partitions.  So that I can use BAT to do this, anyone know if I can use a wildcard, such as XXXX or 5XXX character in the destination forward?  It will use the name of the current domain for the attacker?

  Thank you

  No, you must type in numeric values only

  HTH

  Java

  If it helps, please note

  www.Cisco.com/go/pdihelpdesk

• External calls to CTS-3000 using CUCM

  Hello

  I'm trying to configure the scenario below, and I just want to know if it is supported

  We have a system of telepresence CTS-3000 registered to a CUCM dedicated just for telepresence units. We have ICT trunk between telepresence CUCM and CUCM have registered phones who works for inter-classes calls.

  When I ring a number external unity of the CTS, the call gets initiated and falls straight lines. I registered an IP phone to telepresence CUCM and I can make outgoing calls.

  On newspapers of the CTS, I see a "call ended due to the distance point of endpoint resource unavailable ' error.

  Thanks in advance

  If you try to call from your CTS, through ICT devices on CUCM telephony?  What are the endpoints you are trying to call?

  CTS endpoints use telepresence Interoperability Protocol (TIP) for call control.  Only endpoints speak advanced the CTS models are CTM bridge.  Video normal Cisco phones do not TIP (including 9971, 7985, CUVC, etc.).  Audio only phones also do not speak the TIP.  Basically, the CTS rooms can only call each other without a MCU such as Community trade marks or the server of telepresence from Tandberg/Codian.

• Tandberg Multi Point called endpoints

  Hello Experts from Cisco TP,

  We have Tandberg Profile and Ex 90 end points, I understand the EX series and profile series integrated MCU resource, how do I configure Multipoint calls without using a separate MCU.

  We have ver.6 VCS and MCU 4505. Can make Conference calls using MCU 4505.

  Thank you

  Bobby

  Hi Bobby,.

  You can foind installed on endpoints, it is visible on a GUI on the system information page, section Installed options

  According to the description of the product of C90, it contatin multisite functionality, if it isn't on EX90, then perhaps he is not bought for it.

  You can check the license using the serial number of the device and licensing tool

  Link to the tool: https://tools.cisco.com/SWIFT/LicensingUI/Home#tabbeditem

  Reach:

  • Tandberg Software Upgrade & search

  then click on search and return and step

  Kind regards

  Vivek

• Keys options in telepresence to cucm provisioning endpoints

  To your comment, please

  I wonder if when plug you directly a point of termination in CUCM configuration mode, what happens with the installed option keys?, such as the double video option or the multisite functionality?  ... or all licenses are managed through the tool of CUCM licenses?

  Thank you.

  Options keys will be installed, because they determine what are the characteristics of the endpoint is capable of. They will be also managed endpoint and not CUCM, everything like they are when endpoint is configured either standalone or using VCS.

• A button to push on CUCM registered endpoints

  Hi all!

  I tried to implement a buton to push with CUCM registered endpoints. As far as I understand it, the system must be added to the MSDS directly and not only as the room, therefore RSI can push messages to the endpoint. If I add endpoint to TMS I get error, that endpoint has put the wrong type of provisioning. Accordingly, I am not able to change the settings of reservation, as allow remote booking for MS Exchange integration.

  BBFRR may be available for endpoints registered or is - CUCM this only available for registered endpoints VCS?

  BTW: versions:

  TMS 14.3.1

  TMSXE 3.1.2

  9.1 2 CUCM

  Conductor X2.2

  TS3.1

  Kind regards
  Paul

  [...] If I add the endpoint to TMS I get the error, that the endpoint has set the wrong provisioning type. [...]
  
  

  Hello

  Did you add endpoints to TMS the correct way, i.e. "to list" > "Unified CM?

  Kind regards

  Kjetil

• Reached the maximum of SX20 codec calls once an audio call is connected?

  Hi all

  I have different SX20 devices deployed on our corporate network that are currently on the same version of software: TC 7.2.1.

  For some strange reason that a device does not have a second call (audio) to be placed and added after it has established the first video call?

  Everyone knows this?

  In the State of the system it says the MaxNumberOfActiveCalls = 1 where, as my other systems SX20 say MaxNumberOfActiveCalls = 2?

  I have attached a picture of the number experienced in the tab "call control".

  Thank you

  Brad

  The SX20 has the Multisite Option? Check under the Home tab.

  Ms.PNG

  

  If no Multisite option installed, adding another call for multipoint call will make the second audio call to become involved only and this is a normal behavior. You mentioned that you cannot add another call (audio), is the system put into service and recorded the CUCM?

  Check also under Configuration > System Configuration > conferences what Multipoint mode:

  Ms.PNG

  

  Kind regards

  Acevirgil

• CTS 1.7: Audio snap (call RTC) not heard on all sites

  After the upgrade of our endpoints of 1.6 to 1.7, we met multipoint where we added a PSTN user.

  The audio of the RTC user has not been heard at all the endpoints.

  As soon as we shared an audio presentation was OK on all sites.

  I have a nice SR with that.

  Someone else runs into the same problem?

  See you soon,.

  Martin

  Hi Martin

  BU and DALE were able to reproduce the problem.

  This is incorrect behavior:

  CSCtk61376    CFD: Endpoint MP call RTC does not sure audio component software snap-participant

  Conditions: CTS and CTMS running 1.7.0 software.  Secure Audio component software plug-in point of endpoint is added in secure multipoint call.

  Possible workarounds:

  1 - presentation-sharing is started from endpoint that has made audio snap. Or, Hold/recovery on the endpoint, which makes the audio complement will restore audio to the audio complement in all the endpoints.

  2. - do not use secure audio audio component software plug-in, if possible.

  Default is integrated in version 1.7.1

  Concerning
  Fernando

• Admin password of setting on the SX20 in CUCM - cannot set in peripheral CUCM

  I have CUCM 10.5.2

  SX20 with 7.3.1 code.

  CUCM successfully, SX20 is recorded. Can I change the display name, expansion etc... 'apply changes' CUCM and endpoint learns changes and seems correct. So I guess downloading properly its configuration file and the settings app.

  Device SX20 in CUCM admin page there is a section about 3/4 of the descent called "password and Admin user name"

  It seems to indicate that endpoint admin username and password can be defined in CUCM and pushed down to the endpoint.

  This does not work for me. It is not up-to-date.  Does anyone know if this is really supported?

  SX20 - adminfield.png

  

  I can put it fine directly from the web interface of the endpoint as usual.

  Looking at the Administration TC endpoints running TC7.2 on UCM 10.5.1 on pg 31, you use go by what follows in order for the endpoint to use the name of user and password specified in CUCM:

  1. Use a profile secure in CUCM
  2. Use the built in admin endpoint account
  3. Do not connect not not CUCM thanks to a fast track

  Otherwise, CUCM will count on you to specify an account with administrator privileges endpoint.

• TCS, CUCM, EX90 recording solution

  Dear all

  I need to implement registration between telepresence [EX90, SX20] video endpoint. There is the solution integrated on TCS and CUCM, The SIP trunk between TC and CUCM with the model number of routing TCS.

  Example of

  TC - Extension 9000 [trunk Sip with CUCM]

  EX90 - Extension 1001 [register with CUCM]

  SX20 Extension 0 1002 [register with CUCM]

  Whenever EX90 call SX20., way to trigger the recording to video/voice Trade Commissioner?  

  If I misunderstand the concept., please help give me an opinion.

  Reference: http://www.cisco.com/c/en/us/td/docs/telepresence/tcs/6_2/administration...

  Best regards

  Goal

  If the SX20 or EX90 Multisite option key, one of them can host the Conference.  Any endpoint, it is saying the SX20 must make the appeal out of the TCS.  Suggest you take a look at the sheets and admin guides, they have some information about Multisite.