Desktop HP cannot access the wireless router

Similar Questions

• C4780 cannot find the wireless router

  I have a new iMac and old Toshiba that is running Windows XP and you use a Netgear wireless router.  When I got to the printer, it worked fine on the wireless network.  Bought a new router that I couldn't work with the Mac and the PC so I returned to my original router.  Now, the printer does not work as a wireless printer.  Summaries of diagnosis indicates that the printer cannot find the wireless router and fails under "Network Name (SSID) Found."  On the Network Setup page, my network is listed as a network discovered by the printer.  I guess there is a simple solution and hope to find the answers here.

  Thank you very much!

  Some printers C4780 left the factory with a default misconfiguration.  This could be the reason why you can not see the hpsetup network.  Here is an updated set of instructions for manually adding the C4780 to a Mac:

  Part 1 - Get the printer in Ad-Hoc Mode Wireless

  (1) turn on the printer.

  (2) display the printer has six keys; three on the left (top-left, middle left, below on the left) and three on the right (top-right, centre-right, bottom-right).  Press and release the following touch buttons in order:

  top left,

  bottom-left,

  top left,

  top left.

  (3) you should see the internal menu of printers.  Press the right button down to select 'Service Menu'.  Press OK (lower-left).

  4) press the lower button right until you see "Reset Menu".  Press OK (lower-left).

  5) press the lower button right until you see "half full".  Press OK (lower-left).

  (6) after a few seconds, the printer turns off.  Press the power button to turn on the printer.  It is now reset with the correct default network settings.

  (7) turn on the radio:

  Press the Scan button to get the wireless settings

  Select wireless Menu

  Select wireless settings

  Select Enable Wireless to turn on the radio.

  Part 2 - run the Wireless Setup Wizard

  The printer has now created an ad - hoc network called hpsetup.  To connect to this network on your Mac.

  Check the connection to the printer by opening the printer's internal web page.  You can do this by opening Safari, select bookmarks then ShowAll bookmarks.  On the left pane of Safari, select Hello and on the right, you should see your printer listed.  Double-click your printer and Safari should display the printer's internal web page.

  The printer Web page, select the network tab, and then select Wireless (802.11).  Now press Start the wizard to launch the wireless configuration wizard.

  When the wizard is finished, your computer unplug the printer's ad - hoc network as the printer reconfigures itself to connect to your network home.

  Reconnect your computer to your home network.  Verify that you can connect to the printer at the opening of its internal web page again once we were doing before.

  Finally, install the printer SW.  Since you have Snow Leopard, you don't need the CD that came with the printer.  Instead, open the Print & Fax under System Preferences applet and press the [+] button.  Highlight your printer and click Add.

• Cisco linksys router and cannot access the wireless network

  We have cisco linksys wireless router.  When we installed everything first, we could connect our wireless laptops to the network.  Now, however, the network is detected, but there is no access to the internet.  We have even a guy from ATT were out and he said that the wireless router has been installed backwards?  He installed a dsl fast access on our laptop icon, and now we can access the wireless network but only if we connect as the first.  We can also connect iPod to the wireless network.  They detect the network, but when we enter the password cannot connect.

  Hi JC_3094,

  Welcome to the Microsoft Community and thanks for posting the question.

  According to the description, it looks like you aren't able to access the Internet.

  The likely causes of this problem is if the router is not configured properly.

  Here are some steps that should help you to solve this problem.

  Method 1:

  Check if the router is configured properly to get access to the Internet.

  Method 2:

  Try the steps mentioned in this link and check:

  This tutorial is designed to help you identify and solve problems with a wired (Ethernet) and wireless (Wi - Fi) network connections in Windows.

  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

   

  Method 3:

   

  If there is a frequent disconnection try to update the firmware on the router and check.

   

  In addition, visit these links for more information:

   

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

   

  Hope this information helps. Respond us if you have any questions with windows and we will be happy to help.

• Pavilion G7: Desktop Applications cannot access the Internet but metro apps can

  I have a Windows 8.1. About 5 days ago from desktop applications (IE, Chrome, Google Drive Office) has ceased to be able to access the Internet at all.

  However, apps of metro (metro IE, Facebook, Mail, etc.) can still access the Internet.

  How could it happen? That the two environments use different settings? Is there a setting or registry entry that applies only to the desktop environment?

  Analyses of viruses and malicious software (Malwarebytes and Windows Defender respectively) were not able to do what anyone. But since they are two desktop applications they have not been able to update their files of signatures since this problem started.

  I found the answer on the Microsoft site on this topic.

  The answer is to reset Winsock using this command from an administrator command prompt: "netsh winsock reset" and then restart.

  I did and that fixes the problem immediately.

• Cannot access the BEFSX41 router Config page Win 7

  Hi, I have a BEFSX41and am not able to access my router from any browser config page I have on my system. I use IE and FireFox and when I punch in the IP address for the router there is just there and about 30 seconds later, says that there is a mistake and that the connection has been reset. It is a 64-bit installation and I also have another computer that goes through the same router, is 32-bit and doesn't have this problem.

  I added a NEW driver for my Realtek NIC and it still happens. Another machine that I have on my network ALSO has a Realtek NIC but can still access the router config page.

  Someone at - it else here has the same problem?

  OK, problem solved. I used a different IP and the problem disappeared, thanks for the help.

• Photosmart C4780 "cannot find the wireless router.

  OK so apparently I'm not as tech savvy as I like to think of myself. I just got a used C4780 and spent 12 hours trying to figure how to set up so that I can print wireless. I had zero luck with that.

  I read that the WPS connection method is more easy then I tried that first. After a few failed attempts, I tried to download the software for Windows 8 (as the disc that comes with it only goes to to Windows 7). I got the same error message 4 times (something Microsoft Visual C++ Runtime error), so I then tried the method of the PIN code. After several settings (with the help of my brother on the phone, so I don't really remember what I did unfortunately) just as many failures to connect and I gave up this process.  I printed the 'Network Configuration' Page and the 'wireless network Test report", but I don't have much of a clue as to what it now means. I don't understand what I am doing wrong or what I could do different. The thing that really stumps me, is that the test report said that the printer can't find my router, but at the bottom of the Configuration Page, it lists my wireless network...

  USEFUL/IMPORTANT INFO:

  -HP Photosmart C4780

  -Lenovo all-in-One 8.1 Windows 64 bit

  -router made by ARRIS and provided by my ISP (CableONE)

  -J' installed all the updates that are available for Windows

  -J' restarted the printer, computer, router AND several times

  -my wireless router is in another room, but not more than perhaps 20 feet away

  Side note: I have also a mini iPad... just throw it out there in case it might be a better tool to put up with... If you need to know something more to help me let me know! Thank you for cause in advance that I'm going stir crazy trying to figure this!

  JanessaMarie92 wrote:
  I went on the website of my ISP and discovered that I can't get a new router because of this little note...

  "Cable telephone Service is supported only on Arris modems rented your office of a cable or bought by http://yourbroadbandstore.com/solutions/cableone/."

  Copy + paste directly from their Web site.

  It's OK... you're using their product.  they can always put the Bridge mode.  Call them and tell them that you want to use your OWN router and they put it in Bridge mode.

  EDIT - Bridge mode just turns off the router part and use it as a modem only.

• Pavilion p6 2408eb Desktop PC: cannot access the bios to boot from the disk

  Hello

  I have virus and spyware on my PC. I want to reinstall my drive c with windows 7 instead of 8.1 or at least perform a system recovery, but I can't boot from the drive.

  The only items on google I can find state I must disable secure boot and then enter the bios to set the boot order so it starts on the first disc.

  The problem is that my monitor is idle (power light flashes) when I try to enter the BIOS. I tried to type esc/f11/f1 or press del to enter bios but my monitor then is idle and never enters the BIOS or go to the windows start screen. If it recognizes clearly that I typed bios key because he won't go to the windows startup screen after that pressing said key.

  I also tried recovery windows and tool HP system recovery but at a certain point, it asks me to restart the pc and here again he is stuck at the idle monitor... I never see the start-up of the screen or the other, one that says "press x to enter the bios. My computer will always directly to the windows splash screen once I started.

  Any idea what I might try next?

  Hello

  Consult this publication article before attempting the downgrade of your PC to Windows 7. I have no recommemd making a downgrade on Windows 8 is superior to Windows 7.

  The default settings for the BIOS of your PC 8 version are: inherited and secure boot disabled.

  Erasing the CMOS memory will bring back the default values and then you should be able to start the Windows 7 installation media.

  This similar model PC will have Windows 7 drivers.

  If you have not created the external HP recovery media then you must order at HP if you decide to go back to Windows 8.

• Photosmart 6510 does not have access to the wireless router.

  I get the hardware address to ip assinged that begins with 169 and not the ip address of the network of 192.  Was told by HP support yesterday that he had to do with my pc services at startup it prevents access to the network.  My pc has to do with anything?  The printer is independent and should be able to access the wireless router, all my other wireless devices has no problem with this printer.  Sometimes I can get it but can't always, what is the point of a wireless printer, if it cannot operate as a?  Someone at - it a way to ensure that my printer gets ip address, it must without having to start everything each time?

  No, this router should work perfectly.  There are a few settings on the router that are important:

  1. ensure that the 802.11 g mode, with 802.11n is fine, but 'g' must be present.

  2. make sure that the name of the wireless network is broadcast.

  3. don't use MAC filtering on the router.

  4 set the channel of the router on 11.

  5. make sure that the router firmware is updated.

• The wireless router access denied

  Simple question, I'm sure.

  Router / access wireless, everything works perfectly. I can't just now to manage the device.

  Can Ping but cannot access the GUI front-end server to administer.

  Any Pc / computer laptop XP, Win7, Win8 returns:...

  This page cannot be displayed
  • Make sure that the web address https://192.168.0.1 is correct.
  • Navigate to the page with your search engine.
  • Refresh the page in a few minutes.
  • Make sure that the SSL and TLS protocols are enabled. Go to tools > Internet Options > advanced > settings > Security

  Have checked this and'm sure that's not the issue.

  Hi Gavin,

  1. you are trying to access router webpage wired or wireless?
  2. What is the brand and model of the router?

  I suggest you try the steps from the following link:

  Set up a wireless router (the router setting)

  http://Windows.Microsoft.com/en-in/Windows/set-up-wireless-router#set-up-wireless-router=Windows-8

  Note: You can try to access the Web page of the router by connecting the wired router. If you still can not access the router's Web page, then you can do a hard reset of the router by taking a small pin and do hard reset. When you hard reset you will lose all the settings of the router and you will need to re - configure the router.

  If you are not aware of the configuration of the router, then I suggest you to contact the manufacturer of your router.

  Come back and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

• I have 2 laptops and one desktop. Desktop & laptop are very good. 2nd laptop computer cannot access the internet. I get a message media disconnected. I tried everything please help. I use Windows XP

  I have 2 laptops and one desktop.  Desktop & laptop are very good. 2nd laptop computer cannot access the internet. I get a message media disconnected. I tried everything please help.  I use Windows XP

  Hi JessaRoy,

  · The computer connected to the network or are they computer autonomous?

  · What is the number and the model of the computer?

  · What is the service pack installed don the computer?

  · What is the full error message with the error code, that's all?

  · What are the steps you tried to solve the problem?

  Try the steps from the link below: to test TCP/IP connections by using the ping and the commands net view: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/sag_tcpip_pro_pingconnect.mspx?mfr=true

  With regard to:

  Samhrutha G S - Microsoft technical support.

• The question of the Access Point wireless router

  I am considered to be an amateur when there are routers so patient with me. I have a wireless router in my office and two workstations are hardlined (ethernet cable-joint) to the router. Then, in the living room, I have 3 devices (Xbox, BlueRay, directTV) I want on the network. Rather than running three office ethernet cables, I expect to have some sort of (reverse hotspot) where a device could hop on the wireless router and the signal I inflexible at these three devices. Not sure if this would require an Access Point or another wireless router?

  Any thoughts would be appreciated.

  -J

  I suggest that you try to find something on WET54GS5... is a bridge with 5 ports wireless if I'm not mistaken... but since it's under Cisco Small Business, I suggest you could ask more about it here

  Cisco Small Business support community

  Or you can see WET54G and buy a separate so you switch can accommodate other devices
  

• Unable to access the photo viewer; and also cannot access the desktop icons because they are changed to the photo viewer icon.

  Original title: I tried to apply the photo viewer to open a file and the photo viewer icon replaced each icon on my desktop. Now I can't open anything on my desktop. What is going on?

  The name is below the icon, but the correct icon has been replaced by windows Photo Viewer icon. When I click to open it, it says: windows Photo Viewer cannot open this photo because Photo Viewer does not support this file format, or you do not have the latest updates... I don't know what I did!

  Hi,

   

  Thanks for posting your question in the Microsoft Community.

  From your problem description, I understand that you are unable to access the photo viewer; and also cannot access the desktop icons because they are changed to the photo viewer icon. Please let me know if you do not experience this problem.

  I understand the inconvenience caused to you. I'll help you solve the problem!

   

  Before troubleshooting, I have little information on the issue.

  1. did you of recent changes to the computer before this problem?

  Try the methods suggested in the article below and check after each method:

  Method 1: Icons change incorrectly in Windows: http://support.microsoft.com/kb/2396571

  Registry warning: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the in the Microsoft Knowledge Base: 322756. How to back up and restore the registry in Windows: http://windows.microsoft.com/en-us/windows-vista/Back-up-the-registry

   

  Method 2: Run scan files system (CFS) auditor, to repair missing or corrupted system files.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7: http://support.microsoft.com/kb/929833

  If the problem persists, post your reply with the results and the questions asked above. We are happy to help you further in the advanced troubleshooting steps!

  It will be useful.

• cannot access the internet from the desktop

  I am able to access the internet through the application of start page, but cannot access the internet from the desktop page. The convenience store has not detected a problem. Does not work via Wifi or wired broadband direct.

  Hello

  Are you using the right Internet Explorer?

  There are two more separate... From the start screen and another completely different for the office.

• I can't delete the properties of the proxy server on my HP G60 Windows Vista laptop. Need help to access my wireless router.

  I'd appreciate any help or information that may help me set my Internet Options on my IE LAN settings. The configuration that I need to adjust consists of set the network settings on Auto instead of the designated inputs.

  Hi JoseGarza,

  You can follow these links to configure the wireless router & check if it helps.

  Set up a wireless router

  Setting up a wireless network

  Hope the helps of information.
  Please post back and we do know.

• HP photosmart 5520 cannot connect to the wireless router

  The printer has worked I went on holiday, and now it will not work. I have run the wireless network test, and it says "hp printer is unable to connect to your wireless router.  The wireless router is connected and works fine.  My hp wireless computer (windows 7) works very well.

  The structural 'found ssid network name' report, said down

  But "current configuration" has shown the SSID

  can anyone offer a fix?

  Help

  colleenmercy

  Hi colleenmercy,

  In the network menu, select default network.  This reset the current network settings and will help you reconnect the printer to the network.  You can use the Wireless Setup Wizard or reinstall the HP software to reconnect.