DFM in Ciscoworks.

Similar Questions

• CiscoWorks LMS 3.2 exporting bulk Configuration

  Hello

  Does anyone know an easy way to bulk export configurations off Ciscoworks LMS 3.2?  The only thing I found is the cli command export config u cwcli.exe - p-unit %, but it exports in XML format which is not very readable.  Prefer a text file format.  Someone at - it suggestions?

  Thank you

  Brian

  Hi Brian,.

  CLI, it is the only option, but what you can do to get the files in TEXT format is, you can connect to the server and

  go to this site: NMSROOT\CSCOpx\files\rme\dcma\shadow

  and

  NMSROOT\CSCOpx\files\rme\dcma\devfiles

  Thank you-

  Alya

  * Sides encourage contributors *.

• CiscoWorks LMS 4.1 monitor temperature

  Hello everyone!

  I am creating a poller to monitor the trap of the temperature of my cisco catalyst 2960 Ciscoworks LMS 4.1.

  I created a snmp trap on my device:

  Switch(conf-t) # snmp-server <@IP_server_LMS>SNMPv2c host -I use SNMPv2c

  Switch(conf-t) # Server enable snmp traps envmon temperature

  I created a MIB model Envmon with these variables:

  -ciscoEnvMonTemperatureThreshold

  -ciscoEnvMonTemperatureStatusValue

  -ciscoEnvMonTemperatureState

  -ciscoEnvMonTemperatureLastShutdown

  I created a poller associated with my model, I add my device and when I click on 'Next', I have this error message:

  ###

  No instance are in the devices. This could be because the device is inaccessible, the device does not have the case for selected models or the timeout value is low.

  ###

  Could someone explain to me why I can't monitor MIB?

  Thanks for your consideration and Merry Christmas to all!

  It seems that most of the 2960 have a temperature sensor implemented in hardware and therefore, it shows no values.

  If a device does not show anything on CLI, it is almost impossible that it will display something via SNMP.

  -Thank you

• Cannot start IPS MC in CiscoWorks VMS

  Hello

  I just started getting error (on a pop up Applet), below when I try to run the IPS MC in CiscoWorks VMS.

  +++++++++++++++++++++++++++++++++

  You are not allowed to request the action associated with screenID:

  "/ s510.

  ++++++++++++++++++++++++++++++++++

  Any ideas?

  Run version 2.2.

  Thank you

  Naman

  Do you use GBA or another server authentication to authenticate/authorize the sessions? try to delete the ACS of VMS authentication and try again. The error message is related to an authentication problem. You must also close all your browsers and reopen then.

• Database.pl does not not in ciscoworks

  Hey,.

  I have problems to many problems with Ciscowork. I get the following messages with the self-test.

  Database.pl

  Don't NO Self Test fail to query rmeng. DbVersion, error: server not found database (DBD: failed connection)

  Self-control fail to ask the rmeng. SYSTABLE, error: server not found database (DBD: failed connection)

  The version is: LMS3.0.1

  Any ideas anyone.

  Thanks 1million

  Anthony.

  Delete the file rmeng.log. Then run:

  NMSROOT\objects\db\win32\dbsrv9 f NMSROOT\databases\rmeng\rmeng.db

  Then restart the Manager daemon, and you should be fine.

• Connect nm-cids to ciscoworks

  I need to know what ip I'll use when I connect NM-CIDS with the ciscoworks

  either the fa0/0 interface or sensor ids or IP that entitlement in the configuration of the sensor or that we

  question 2: port fa0/0 connect to the hub for sesing or not?

  I forgot to mention this f0/0 interface on the CIDS module needs to be connected to your local network, as it comes to the management interface. and if the gateway IP address and defautl configured the config interactive installation must be on your LAN range. For detection you must enter the command mode interface of the ROUTER below. Traffic will be copied from this interface to the inspection module

  ID-service-monitoring module

  I hope that helps...

• How to reset the password on a Windows-based CiscoWorks LMS 3.2?

  I have problems with the procedure for recovery of password on a 3.2 CiscoWorks installation. The problem is that I have no idea what versions of software are running (track never cared).

  I tried following the steps here: http://www.cisco.com/en/US/products/sw/cscowork/ps2073/products_password_recovery09186a0080107dee.shtml (twice) and I was impossible to reset the password.

  Is there something that I am missing? Something extremely obvious I forgot?

  Thanks for any help!

  Use the resetpasswd utility:

  NMSROOT/bin/resetpasswd admin

• DFM.log grows up to 3 Giga in 3 weeks

  Hello

  IM using cisco works on a windows server system every 3 or 4 weeks my backup fails due to "no disk space.

  Looking for the reason why I found that DFM.log is too large. After deleting this file, the backup will run propperly.

  Remove this file should stop/start crmdmgtd.

  Looking in DFM.log shows the number of output lines from discovery and I guess that's the output of a command to debug.

  in DFM > configuration > configuration of logging logging level is not defined.

  Months ago I had a problem with DFM and got help from Cisco by an opend case. I remember during the work for

  this case, I was tasked to set up a few commands such as:

  If DFM dmctl put REAL ICF_TopologgyManager:ICF - TopologgyManager:DebugEnebled

  Maybe I need to invert the controls, but you are not able to use orders dmctl.

  Can you elaborate on what you mean by "you couldn't use dmctl commands?

  Could not execute the following command for reverse debugging?

  C:\Program Files\CSCOpx\objects\smarts\bin > dmctl s DFM set ICF_TopologgyManager:ICF - TopologgyManager:DebugEnebled

  FAKE

  If so, what error messages do you have?

• With the help of CiscoSecureACS with CiscoWorks RME

  I need help in configuration of CiscoWorks for use CiscoSecureACS for authentication of the connection. I've specified GANYMEDE + as the module connection. I am able to connect with an account of the ACS server. However, the permissions are not set correctly. When I connect with on behalf of ACS server, the options are not displayed (for example, under Administration, inventory, RME, add devices... the Add Device option is not present). Please notify.

  To be concise, ACS is not all the fields required by Ciscoworks. This is why you should always define user profiles in ACS.

  ACS is simply an authenticator. CiscoWorks always manages permissions. Look at the available in Ciscoworks fields and you will see there are a number of roles that each user can take. I guess that Cisco may include one day extensions in ACS to manage specific areas of the CiscoWorks profile, but this is not the case today.

  I think that the advantage of using ACS is centralized authentication. Users do not have to change their passwords in several places. Logon violations are stored in one place.

  You will find that when you set profiles in CiscoWorks they will remain fairly static.

• Question of vulnerability scan yellow CiscoWorks Nessus

  Hello

  Analysis reports of Nessus vulnerability yellow for our CiscoWorks server:

  x.x.x.x (ip address of the server, CiscoWorks) YELLOW Sybase ASA Client connection Remote Broadcast

  Disclosure unit locate information on the Sybase server

  sybaseanywhere 2638

  If anyone knows the status of this issue, please let me know.

  We have the following CiscoWorks product and version:

  LMS (2.6)

  CiscoWorks Common Services 3.0.6

  Director of campus 4.0.6

  CiscoView 6.1.5

  Device fault 2.0.11 Manager

  InterNetwork Performance 2.6.0

  Resource Manager Essentials 4.0.5

  Your help would be greatly appreciated.

  Thank you.

  GY (Gongyuan Yao)

  Contractor (support of the LHC network)

  [email protected] / * / 301 - 435 - 3168 (o)

  240-417-1488 (c)

  It's CSCsk35018:

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsk35018

  Following two discussions will highlight extra on top of what provides the tool Bug:

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=network%20Infrastructure&topic=network%20Management&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40^1%40%40.2cc0b896/4#selected_message

  http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Network%20Management&topicID=.ee71a02&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cbec487

• First management LAN CiscoWorks LMS or Cisco? Help

  In my business, we look adds a network management solution:

  Some time ago, we installed CiscoWorks LMS 3.2, but we decided to install on the other more modern solution, what is the solution which recommend me?

  Requeriments:

  1 000 devices from cisco management.

  Regularly perform massive configurations.

  Constant monitoring of the network infrastructure.

  Backups of configuration.

  We have two solutions:

  -Update the current CiscoWorks to LMS 4.x version

  -buy the "First Cisco LAN Management" Solution

  What solution that recommend me?

  Thank you for your attention.

  Kind regards.

  Hi Jeffersson,

  The current product packaging is a bit confusing. Cisco is rebranding all of their management under the aegis of the first Cisco solutions. All prime products have a common appearance and take advantage of some approaches architectural.  From LMS 3.2 on 4.x will put you in the first territory of Cisco.

  In the 'first' products are (among others) "Cisco first Infrastructure" (also known as PI - 1.2 is the current version) and "Cisco first LMS" (4.2.3 is current). Preferred Infrastructure (1.0) began in the successor to management wireless Cisco (NCS) product and had been adding features on the way to bring it up to parity with LMS functionality to wired infrastructure. He isn't quite there right now (current comparison here) that existing customers of LMS are usually advised to stick with the latest version of the LMS for now.

  Still with me? Good. If the extra twist is that 4.2 LMS is "included" with licenses of FT 1.2 - see the link guide below. So, if you want LMS 4.x, you order indeed 1.2 FT with licenses "Cycle of life" according to the number of devices you manage. (There also is 'respect' and 'insurance' adding these new features of the respective licenses. Compliance is available from LMS 4.2 in the CAAM.  Insurance is almost a FT 1.2 functionality only.)

  So my recommendation to you would be to upgrade to version 1.2 of PI and to install and to use the LMS 4.2 (4.2.3 and put patched up-to-date with all the packaging of the products). If you have a VMware configuration, deployment option flexible device (file eggs) is the easier implementation,.

  You may find it useful to explain this point of view of Cisco the following two links:

  Functional reference LMS

  Control of IP and Licensing Guide

  Don't worry not-all this will not be on the test.

• CiscoWorks LMS 4.0.1 and 3850 switch support

  HI, I want to know if the 3850 switch is supported in ciscoworks LMS 4.0.1 I added devices, successful inventory collections but peripheral icon is blue with question mark '? ' and config sync always fails.

  I tried to download the packages to install it, but I couldn't find it.

  Thanks help fo

  3850 is supported on LMS 4.2.3. Check the list supported here:

  http://www.Cisco.com/en/us/docs/net_mgmt/ciscoworks_lan_management_solution/4.2.3/device_support/table/lms423sdt.html

  You must upgrade to 4.2.3 LMS or 1.3 FT go.

  -Thank you

  Vinod

  *Side encourages contributors and it's really free. **

• Question of discovery for the DFM "stuck in Questioned state devices" device

  Hello

  We have LMS 3.0.1 installed with DFM 3.0.4 devices display Questioned with error code "SNMP timeout" without any specific reason. The snmpwalk is coming to the unit I checked with the snmpwalk command. The only device discovered as "known" has authorized ICMP from the server to the device and any other device. They don't have that SNMP permit. This reach the dicovery? or what else can I try... Please think!

  Rgds

  Yes. DFM requires that all SNMP and ICMP accessible devices. DFM uses the ICMP protocol to check accessibility to all IP addresses on the device. However, at the very least, the address by which you manage the device MUST be accessible ICMP.

• CiscoWorks - freeing of disk space

  Hi people,

  Our old CWLMS 3.2.1 becomes short on disk space, it was suggested that the directories named 731, 732 and 733 on the D: drive could be deleted. The three directories seem to have the same subdirectories (see attachment), were all created in February 2012, and use about 5 GB of space each.

  I don't know if these three records are essential to the operation of Ciscoworks or whether they are the remains of some maintenance actions; In short, I can remove them?

  Thank you

  Scott

  Hi Scott,.

  What are the backup of the theCWLMS .  If you have kept 3 different instance of the backup of the LMS.

  If you have another backup somewher then you can remove all three, or you can atleast remove 2 and keep 1 to be a safer side.

  Thank you-

  Alya

  [Note the useful post]

• DFM 3.0.1 about device discovery

  Hello

  I have a problem of DFM 3.0.1 device detection.

  I installed LMS 3.0.1 on a stand-alone server based on VMWare Infrastructure 3. Common services, Campus Manager, CiscoView, RME and IPM properly so far.

  When I tried to import DCR in DFM devices, the status of the discovery still hangs on "pending" or "learning" with an increase of 10%. I also noticed that the two processes are always stop automatically on the server whenever the server is restarted:

  "DFMCTMStartup, the DataPurge process are declining.

  Advice to solve this problem please? I thank very you much in advance!

  Richard

  What version of DFM have you? If less than 3.0.3 you should switch to 3.0.3 to see if it is the known bug of DLL conflicts.