Impersonation on a T1 with ISDN router

Similar Questions

• A WN3000RP will work with a router SMCWBR14S-N4

  You want to buy a range extender WN3000RP on Amazon, but do not want to go through the hassle of return it (if it is still logged) if it does not work with my router SMCWBR14S-N4. Anyone has any experience? (product description says it's 'universal')

  Thank you!

  Hi rapnet.

  Yes, please see the installation manual:
  http://www.downloads.NETGEAR.com/files/GDC/WN3000RPV3/WN3000RPv3_IG_8Jul14.PDF

  Located at the support page:

  http://support.NETGEAR.com/product/WN3000RPv3

• R7000 as router with the router for mobile broadband Internet

  Hey guys. First of all, my apologies for my somewhat inadequate English skills. Secondly, I am brand new to the community, so apologies in advance for any fault :-) Third stop, apologize for having a complete beginner :-D

  So, for the issue: I recently bought a router top mobile broadband 4G (4 G MBR) to my apartment, because of the gap of strength and speed signal very low quality of the cable to the ground on my Street (fiber is to come next year).

  But the router provided by my operator isn't on par with my router R7000 Nighthawk when he comes to reach wifi, wifi speed, number of outputs of LAN and power of the processor.

  So, I want to use my R7000 my router, the internet signal from the air to the 4G MBR, then by cable to the WAN of the R7000.
  In other words; I want to just 4G MBR to simply pass / transfer the internet signal to my nighthawk R7000 router so I can use the R7000 as my router, LAN and wifi.

  How can I set this up?

  Thanks for your help!

  Update: the MBR has been no help at all. As far as I could tell, there is no possibility to bridge or pass-through mode. The R7000, as she does the work. I just put it in AP mode, adjust all the wired connections DHCP/auto IP assign and everything works great.

• "Gateway router not found" error when you try to connect the TiVO DVR with DLink router.

  Original title: gateway router not found

  try to connect the tivo series 2 to the internet with dlink router that he used to work with previous tivo but not with tivo now, it says gateway router not found
  However, my laptop works fine with the router, I tried tivo support nothing helps, too, if I use the phone line works of tivo, but do not store a lot and is running out of room so it will not work fo rme, helllpppppppp thanks

  Hello

  Where exactly you get this error message?

  See the troubleshooting suggested in "Network error message N07 or C107" steps from this link.

  If you try to connect the tivo series 2 to the internet with dlink router then check out the link below:

  http://support.TiVo.com/app/answers/detail/A_ID/400

  Please contact the manufacturer.

• Unable to get online with new router-"Local access".

  Original title: can't get online with new router.

  I'm having a lot of trouble to get online with my laptop.

  My roommate has recently got a new EE Brightbox. It works perfectly well with his laptop and mobile phone. Also works with my mobile phone. However, when I try to use my laptop it only gives me "Local access". I have no problem connecting to the router, but it just won't let me go online.

  Tried to disconnect/reconnect the connection Wireless on laptop from scratch with wired connection to router, router and router reset re-booting. None of them have worked.

  Any help would be great?

  Laptop works on Vista.

  Hi Rob,

  Thanks for the reply.

  Have you tried methods of resolution of the problems mentioned in the previous answer?

  Please update the State of the question, we are here for you help!

• How to configure the network home wiFi with dlink router

  I need to create a home network using the dlink WiFi router
  a computer with Vista and the second with XP
  can someone tell me what havo to do to configure the router etc etc o give me same informamation on where I can learn to do
  I want just the old pc with xp for the server and the vista one customer but more importantly I need the file on XP to migrate under vista.
  Thank you very muche for your end of the patient cooperation
  in return, I give free cooking classes
  see you soon

  I'm not sure if you are asking how to set up a secure wireless network, if you ask how to share files between your two computers (and there is no "customer" or "server" in a working group, in a field - which is not), or both.

  So I will give you information on doing both.

  Router - configure manually

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.
  2. attach a class (usually supplied with the router) ethernet cable cat5e port Internet/WAN from the router to the ethernet port on the cable modem.
  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.
  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine. The first thing to do is to change the default password because * all * known default passwords for different routers.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar. ;-)

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). Most computers purchased during the last 4 years have the wireless hardware that will support WPA2-Personal (also known as WPA2-PSK). This is the desired encryption level. If your wireless hardware is older, use WPA. Don't use WEP, because who is easily broken within minutes. So go ahead and set the Security Mode WPA2-Personal. Do this and enter a password. For example, you could use the password ' here be dragons, beware you scurvy dogs! The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the ethernet cable and wireless of the computer should see your new network. Enter the password that you have created (exactly as you wrote it with all capital letters and punctuation) to join the network and start surfing.

  Networking

  Here are the steps of general network troubleshooting. Just cannot apply to your situation, so just take the bits that are. It may seem daunting, but if you follow the steps in the links and suggestions below calmly and consistently, you will have no difficulty to implement your sharing.

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  XP - configure Windows to login automatically (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  Vista - Start ORB > Search > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.
  MS - MVP - Elephant Boy computers - don't panic!

• Problem with wag160N router wireless

  Hi all. Sorry for the typos etc I am new in the forum :-). Please, if the subject has moved to another subforum do it.

  So, here's the problem: last week, I bought the WAG160N wireless-N adsl2 + modem router (version 2) and yestreday I formatted my laptop 2, so today I decided to install a new one.

  I work 2 hours on it now, but still I can't find a solution. I started with the first cd, as required by the guide. Everything works well until the installation wizard step that attempts to connect to the router. At this point, he's looking for 5 minutes and then he said that he is not able to communicate with the router and wonder to check the connection again. I connected everything as it should (the gray wire of telephone jack to the socket of the router that says DSL, cable - ethernet - yellow of Gate 1 of the router ethernet for the laptop and then the AC/DC to the router and power.) I click next to the installation wizard, then he said to the power on the router... I do it and it checks then 5 minutes and again, he says that can't find it and tell me to double check and the story goes like this. I made 6 - 7 times but nothing. I also used the netwotk magical Wizard that was installed to fix the problem (because it recognizes that there is connection problem), but is not able to set in! What should I do? The ISP said that they don't sell Linksys products for their stores (I do not know the ISPS work on other countries, here they sell routers, adsl packs ect in their store) so they can't provide me with support. Can someone help me? Its the first time I use a linksys for me product and I don't know how to install it without the cd.

  I use windows vista pre sp2 on two laptops.

  I must also say that I have no problem with the ethernet connection the baudtec my ISP gave in the pack, that I bought when I activated my ADSL (2 years ago). IM connected with it now to view the topic.

  Sorry for my bad English and im sore right now that I can't think of what other info you might need, post and I will answer you.

  Thx for reading.

  Hello

  Connect your device directly to your pc via ethernet cable.

  Try to find the ip address of your device using the arp - a command

  Try to ping your router/adsl with address (192.168.1.1) ip of the device. u should get a response, if no response then in your pc check the LAN connection properties and enable DHCP.

  If you get always no response to ping the device, try and set an ip address in the range (192.168.1.1 or whatever your ip devices). Now, try to configure the device to cd Wizard help.

  Correct me if im wrong.

  Concerning

• FTP with WRT160N router wireless problem

  I upgraded my router WRT54G, a little back and ever since then, I can't get my (CuteFTP 7.0) FTP software to work.

  I didn't change anything with the FTP software. The change ONLY on my system is the new router.

  Is there some sort of setting I need to change so that he could afford to FTP?

  OK - so I fixed it. I think that there is something more big wrong with my router at first. The night last wired connection to my wife worked very well and today he was completely dead. In fact, since I updated the firmware on the router about a month ago, his internet connection was for crap.

  I hooked the computer directly to the cable modem and it worked perfectly.

  So this morning, I bought a WRT54G2 - just hung and EVERYTHING worked from the outset - including my FTP software.

  My suggestion for buyers... avoid the 160N. I'm bummed I wasted $100ish on mine only to get the 2.5 use PITA.

• Trouble with my router WRT110

  Hello! All this problem started when I upgraded the machine I'm typing this on Windows 7 Ultimate.  No matter what I did, it wouldn't connect to the existing network. I finally found a way to connect by entering the identification number of the router, but it created a completely new network. My problem is here. I can create new networks open very well, but even if I try to create an encrypted network, it won't work - the computer does not detect the router. I need a network encrypted because I am required by law to have one in my business, and I have no idea how set up. The network is composed of this machine that I use a Macbook and a TiVo DVR, as well as my laptop which is being repaired. I might also add that I have a problem with the software that came with the router. Ideally, I would have a secure network with a password that is easily memorable so that can reach other machines. I spent many hours on this I'm really at a loss, and some instructions step by step would be greatly appreciated. Thanks in advance,

  ~ Eric

  1. you should always access the web interface via a wired connection. Through a wireless link, you can configure the router of your neighbor accidentally. And of course you should also never make changes on settings wireless via a wireless link. So, always use a wired connection only for this purpose.

  2. it does not affect your network as it is. It only changes the configuration of the router. If you change the configuration of the router wireless, of course, it will affect all existing wireless links to the router (if any).

  3. you must not choose a password "easily memorable. It's always a bad idea. The wireless password is usually only once entry on each wireless device to connect to the router. The wireless device usually remember the passphrase. Thus, it is best to choose a strong password, for example a random generated password longer. It is much safer.

• There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.

  There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.
  I tried to connect my xbox to my computer to xbox live via the 3g router, but I was unable to. According to me, there is something wrong with the network card, since neither the wifi (wlan?) nor the lan connection seem to work.
  I harnessed connected my iPod, Xbox 360 and Nintendo DS for her, but not my computer. Please help me, what wrong with my computer?

  original title: problem with the map?

  Hi GustavTak,

  1. you have made no changes to the computer before the broadcast took place?
  2. do you get an error message?

  Try the steps from the following link:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Set up a wireless router
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-wireless-router

• Windows Vista is not compatible with Sagem router?

  My laptop does not connect to my Sagem sky router but will connect to other wireless connections. When you use the Ethernet cable, it connects but does not identify the network name; When I try to connect wirelessly it says unidentified network, local access only. 2 other laptops in my house to connect to the router with no problems. I have tried to change the channel, change the type of encryption, I reset my router, checked the properties of the adapter, uninstalled McAfee and even spent an hour on the phone with Sky today to be told that my laptop is simply not compatible with the router. My laptop is running Vista Home Basic, and use two other laptop computers XP and Windows 7. The upgrade to Windows 7 would solve the problem? I don't want to pay for the upgrade, if I'm still not able to connect to the Internet.

  Click with the right button on command prompt and select run as administrator - type the following command

  netsh winsock reset

  Press enter

  Now it works?

  Have you tried: disconnect the battery & leaving for an hour
  change the channel on the router
  change power options
  verification of the IP address is detected automaticall
  Uncheck for automatic IP address
  Change the firewall settings/turn off the firewall
  installation of the SP3
  Tour of WPA security
  He turned back
  tried switched to WEP

  There's a fixit here.  If editing the registry yourself, do exactly what he says.

  http://support.Microsoft.com/kb/928233/en-GB

  1. run regedit.
  2. navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\tcpip6\Parameters\DisabledComponents. If you do not see DisabledComponents, create one by adding the following registry value (type DWORD).
  3. change one or a few values:
  1 = disable tunnel interfaces
  2 = disable 6to4
  3 = DΘsactiver ISATAP
  8 = disable Teredo
  16 = disable LAN interfaces and PPP
  32 = preference set of IPv4 to IPv6
  255 = disable full IPv6

  Note: 1) you must restart the computer for changes to the DisabledComponents registry value to take effect.
  (2) this method disables IPv6 on all your interfaces LAN, connections, and tunnel interfaces but does not disable the IPv6 loopback interface. You must restart the computer for this registry value is taken into account.

  II.

  1. open the properties of the local area network.
  2. uncheck the box next to the Internet Protocol version 6 (TCP/IPv6) component in the list under this connection uses the following items.

  This method disables IPv6 on your connections and LAN interfaces, but does not disable IPv6 on the interfaces of tunnel or the IPv6 loopback interface.
  -AndreaPB-

  http://social.technet.Microsoft.com/forums/en-us/itprovistanetworking/thread/1e26fb5b-7d35-47ad-a50d-2025737da6b0/

• Printer not responding not connections (wireless printer) is good and solid. I replaced my old router wirelessly with a router of valuation. I had to plug it, but the printer does not respond now.

  Printer not responding not connections (wireless printer) is good and solid. I replaced my old router wirelessly with a router of valuation.  I had to plug it, but the printer does not respond now.

  Is what brand and model of printer?

  I do not work unless your new router has the same SSID and password wireless as the old. Consult your printer documentation to find out how to handle the situation. For example, some Lexmark wireless printers have a program called Configuration Utility Wireless in the Lexmark folder under all programs on the start menu that is used to set up the printer when changes are made to the wireless network.

• Printer wireless connected but offline with new router Xfinity

  A FIOS Actiontec router wireless, printer HP 6515 functioned well as a wireless network printer.  Just replaced FIOS with Xfinity Cisco router.  Shows printer HP 6515 as connected (print network configuration page) but both PC (Windows 7) indicate printer is in offline mode (no check mark).  Printer has set the IP address with FIOS router.  Running doctor printing & scanning HP without success.  Suggestions?  Thank you!

  Replacement of your wireless router try here.

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html

• Loss of connection with my router, shows only limited access and my network showed that unidentified

  Original title: unidentified network, missing the default gateway

  Hello

  So one day out of the blue I lost connection with my router. I was able to reconnect but this time around I had only limited access and my network showed non-identified. I tried to connect to a different wireless network, same thing. When I run ipconfig, I'm missing a value for the default gateway.

  I tried to:

  -Reinstall the drivers for the adapter

  -update the drivers

  -Reset my router

  -Gateway ipv4 manually of entry

  -kill lan via Device Manager drivers

  -scream at the computer

  I have a Setup to dual boot with Linux Mint along side Windows 7. When I boot in Linux it connects to any network without problem.

  Some help would be appreciated.

  Plug

  Windows 7 Ultlimate

  I7-4700MQ @2.4

  GTX 765M 2 GB

  8 GB RAM

  1 TB + 240SSD

  Realtek RTL8188CE wireless

  Hello Alex,.

  Thank you for your response.

  I appreciate your time.

  I suggest you to uninstall the network driver wireless and reinstall in compatibility mode.

  To uninstall the driver, follow these steps:

  a. press Windows + R keys together, type devmgmt.msc in the run window and press ENTER.

  b. Click to expand network adapters, right-click on the map and click Uninstall.

  c. restart the computer.

  Now you can Download driver from this link wireless.
  Reference:
  http://downloads.Eurocom.com/support/drivers/zip/238/238_RealtekWLAN_W764.zip

  For reference:
  EC http://www.Eurocom.com/EC/drivers (238)

  To reinstall the driver in compatibility mode, follow these steps:

  a. right click the driver file, and then click Properties.

  b. click on the compatibility tab.

  c. click on check "run this program in compatibility mode for" and select Windows XP(Service pack 3).

  d. click apply and ok.

  Now, install the driver.

  Please keep us updated.

  Thank you

• When you try to add a network route with the "route add" command in the command line, I get the message "the requested operation requires a rise."

  Elevation required to route add command

  When you try to add a network route with the "route add" command in the command line, I get the message "the requested operation requires a rise."  What is the correct syntax to use?

  You can watch using the PowerShell...

  http://TechNet.Microsoft.com/en-us/library/bb978526.aspx

  http://TechNet.Microsoft.com/en-us/scriptcenter/dd742419.aspx

  .. .and post questions about Windows PowerShell forum...

  http://social.technet.Microsoft.com/forums/en/winserverpowershell/threads