Port replicator 2504 and w530

Similar Questions

• Portege Z30 16 GB with high speed Port Replicator III and two monitors - resolution

  I have a Portege Z30 with 16 GB of Ram, connected to a Toshiba high speed Port Replicator III which is connected to two monitors running in mode extended.

  The monitor attached to the first section of the video is 1920 x 1200 running.
  However the second monitor is only show support for a maximum of 1280 x 1084.

  The monitors are identical, and both are connected by DisplayPort cables.

  I tried to lower the resolution and save the settings on the first monitor to see if it offered options on the second monitor, but the options remained the same.

  At this point, I have narrowed down to 1280 x 1024 so that it conforms to all the monitors but would like to a plus-res solution.

  Does anyone know if there is a fix/work-around for this?
  If this is a hardware limitation, has anyone tried a USB 3 to DisplayPort adapter in a similar configuration?

  Thank you!

  At the same time using two displayports?
  I wonder how it is possible, because of my knowledge it is not possible... as far as I know the Port Replicator III supports two DisplayPorts but you could choose and use one of them...

  In any case, you can use both with a lower resolution, I guess that this problem can be caused due to incompatible display drivers.
  I suggest you to uninstall reinstall or update the display drivers and check if it helps

• Express Port Replicator II and Tecra A10 - 12Z - only the power and LAN

  Since my Toshiba T3600CT I received with docking station, I discovered that I have a docking station. In the meantime, I had a small Sony who had no docking station, for which I got one of the first USB docking station and since then I've seen always to get laptops with docking station.

  But this time something went really wrong, the Toshiba Express Port Replicator II PA3680E-2PRP provides only power and LAN. There is no power in the USB ports, so no serial port or the sound, and DVI and VGA are also disabled.

  All these ports work fine on the Tecra A10, but not on the docking station.

  Of course, it is nice to have the power and LAN, but not when I expected too much of everything.
  So I was wondering if anyone has had a similar problem, it is like upgrading the BIOS for me who have not installed all the necessary software, or is it a fuse or something I could fix myself or is it a faulty docking that shouldn't have left the factory?

  Hello

  What's your Tecra pre-installed with original recovery image?

  When the laptop is preinstalled with recovery image simply connect compatible laptop Toshiba docking station and all the devices connected to the docking station will be recognized correctly and all available ports should work fine.
  Is that a Port Replicator basically "replica" ports on the laptop.

  On this virtual path, we cannot say that this port is 100% OK. What can you say about it? you bought is used a?

• Problems with an external monitor with the Port Replicator III and M100

  Hey all.

  I just returned from a trip where I took my laptop. Plugged into the Port Replicator port, started and everything was fine. Then after an hour or two, the monitor stopped receiving a signal. I repositioned the laptop and everything was good again. He then loses signal once again, and I was not able to get a signal via the port replicator since.

  The monitor works fine through the hole at the rear of the M100.

  I checked the pins on the Port Replicator port and portable, none folded and tried to clean any dust etc. Still no signal to the monitor.

  Someone has ideas of how to do to solve this problem?

  Jamo

  Hello

  The Toshiba 3 mobile extension is responsible for the good condition of the duplicator 3 market. Try to reinstall this utility and also check the page of the Toshiba driver for updates.

• No Audio or USB ports with Port Replicator 3 and Portege R600

  I have a problem between my Port Replicator 3 (PA3681E-2PRP) and my Portege R600-13 X (Win7 Pro 32-bit). Everything has been working well for the past few months until a week ago. My PC has developed a problem then that plugged on the Port Replicator, it will not recognize something new that is connected to the USB (two PC & Replicator ones) ports, the Replicator audio output no longer works and the PC hangs during shutdown. Everything is OK with the PC when booted without the Replicator, but as soon as it is connected to the port replicator, in this case.

  I tried looking for information about this problem, but nothing helps... Any help to fix this would be greatly appreciated as it is to set up a business and I need it to work properly.

  A few things to try:

  Reinstall the Toshiba Value Added Package.
  Use system restore to restore Windows to a previous state.
  Check the connector for docking station for damage.
  Back up your data and perform the recovery.

  If its still does not, then I would send the laptop and the Port Replicator Port for an ASP for repair.

• Advanced Port Replicator III and Tecra M5 - compatibility issue

  Hi all

  Had a brief search, but could not find a similar position.

  Is the Advanced Port Replicator III PA3314E-1PRP compatible with a laptop Tecra M5?

  Thanks in advance and amicably.

  James

  Yes, it is compatible, I can confirm this info above
  If you wish, you can consult the Web of Toshiba Europe site Options & accessories.
  You will find this info useful

• USB Port Replicator II and IEEE1284 - Windows XP

  I have a replicador (Px1098e-1prp) port and it is impossible to operate LPT (IEEE1284) however in Windows 98 works perfectly. I have a M30-801 and I also proved in several computers, and it won t work with Windows XP. How can I do works?

  Thank you!

  Hello

  The only thing I can tell you is that you need to check the user's manual and it is described how you set up the printer in Windows XP Home edition. You can find it on page 24 (English).

• Portege R500: external monitor does not work with the Port Replicator Port 2 and DVI

  I have a Portege R500 running Vista with a slim Port Replicator II and digital monitor Viewsonic.
  I connected the monitor to the DVI port on the port replicator and got it to work OK.
  Press fn + F5 would switch between the computer screen and the external monitor.

  Then it stopped working, and I can't make it work at all. F5 recognizes just the laptop screen.

  If I connect an analog display, it is fine, and I can pass between the two screens without difficulty.

  The strangest thing is that, if I reboot when the Portege R500 is docked, the digital monitor begins by displaying the boot sequence, but then the signal is lost as soon as the screen stops the display of the progress (in low resolution) bar.

  I spent an hour on the phone to support Friday, and he made me nowhere.
  They finished by saying that he should never have worked! So what is the DVI port because then?

  Any ideas?

  David

  Connect your monitor directly to your laptop and see if it is recognized and you can go through FN + F5 between the two views.
  If it works, then connect with port replicator, and then try again.

  It's probably best if you reinstall display drivers. Maybe there are new too on the download page.

• Port Replicator III + very high CPU when you move the usb mouse only in W2k

  Tecra M2 with a port replicator III +.

  It is set to dual boot XP and Windows 2000 (yes I know it is well a bit but I have a bunch of stuff installed in win2k it is difficult to find these days).

  XP is very good at 100%, but with win 2000 if I use my * USB mouse * on the * ports port replicator and waggle the mouse around - the * CPU * jumps from 0 to * 70 + % * use (System process that seems indicatates like IRQ problem). If I plug the mouse into the ports of the laptop (when the laptop is connected) - it's fine, no more than 5% cpu usage. It's a microsoft basic mouse. I really believe that this is a problem of usb any, because the cpu jumps a little if I type quickly on my usb keyboard (only a few %). It comes with the usb ports on all the Replicator.

  Any ideas? I don't really want to plug my mouse in the morning because it beats a little interest to have a docking station in the first place! I have installed mobile extensions. All other aspects of the replicator are fine

  Martin

  Huh it will not be easy to find the right explanation for this.
  At the moment when Tecra M2 has been offered on the market as Replicator port compatible Toshiba offered Toshiba Advanced Port Replicator III (no +) and at that time both supported in operating system has been tested with it.

  Toshiba later designed Toshiba Advanced Port Replicator III + and confirmed the compatibility with Tecra M2, but obviously with more recent WXP (at this time).
  So now, you've been following situation: you use most recent Replicator port, but with much older operating system so I assume that there may be a compatibility issue with W2K.

  I can't imagine use you so often with W2K and if so, may not be so problematic to connect the mouse directly on the cell s USB port.

  Sorry, but I don't think that there is nothing you can do about it.

• Tecra A8: Problem with the USB printer connected to the Port Replicator III

  Hi all

  I have a problem with my Tecra A8, year Advanced Port Replicator III and a USB printer. With the printer connected to a USB port on the Port Replicator, I have to wait 2 minutes for printing to start. When it is connected directly to a USB port on the laptop and the laptop disconnected from the Port, printing starts immediately. I have the latest drivers from the Isensys of Canon LBP 2900 installed and Windows Vista professional as the operating system.

  I called the technical support of my country, but her is not recorded similar problems.

  A person with similar problem? Some help would be very appreciated.

  Thanks in advance.

  Hello

  Seems like a strange question... Already done the standard procedure in the event of such errors? :)

  The standard procedure is somehow similar to the following:

  -Update your BIOS
  -Update all the drivers for your machine
  -Update your printer drivers
  -Update your operating system

  If all else fails, then try an another Portrep if available, maybe you need to contact your dealer for an another portrep for the test.

  Something like this should be your way. And then you sucessfully made a TROUBLESHOOTIN´ ;)

  I'd be happy to hear feedback from you on your situation...

  Welcome them

• Connection of two screens on the PA3508E-1PRP Port Replicator

  Hello

  Anyone know if you can connect two screens on the port replicator? and use it with the option "extend my desktop" in Windows?

  Thank you

  Concerning

  It seems that you're talking about the Toshiba Express Port Replikator for Portege M400.
  In my view, the Port Replikator Express supports simultaneous use RGB & DVI only if the portable computer system unit itself also supports the simultaneous use of RGB & DVI.

• Portege R500 - Slim port Replicator II: dual monitor DVI & RGB all

  Is it possible to use a double configuration monitor on a Port Replicator II slim if I connect a DVI-port monitor and the other to the RGB port?
  I have a laptop Toshiba Portege R500.

  TIA

  Hello

  I didn t find all the information about the Advanced Port Replicator II but I found some info on Advanced Port Replicator III and the simultaneous use of RGB & DVI ports

  So the point is it's possible * ONLY * if portable system unit _itself also includes simultaneous use of RGB & DVI support_.

  concerning

• Double screen does not not on 2005pr Port Replicator

  Hi all

  I have a Usb 2.0 Port Replicator 2005pr and I used it with my HP Pavilion 14B Ultrabook (Windows 8) because there is no dock for it. Everything worked ok but I had to return my laptop HP to fix and when he comes back I have to reinstall everything.

  The dock did what it did before that works for the spart form the VGA port so I can't get both screens to work. I solved this last time after messing around a bit, but don't remember what I did, I can't seem to sort this time and I am very bored.

  Someone else has an idea on how to get it working again.

  Thank you

  Graham

  Hey all

  HP gave the solution in the end.

  In case anyone has the same problem, I had to refresh the laptop and install the drivers for Port Replicator FIRST, this seems to have sorted, something I install after must mess with it. But the installation of everything after the duplicator works is fine.

  G

• Satellite Pro A60 and Port Replicator

  I JUST BOUGHT A SATELLITE PRO A60 AND USB2 PORT REPLICATOR. WHEN I ATTACH MY LASERJET 1100 AND PRINT A TEST PAGE IT PRINTS WELL BUT IF I PRINT A WORD DOCUMENT IT RELEASED FOR EXAMPLE GOGGLEDYGOOK. CAN YOU HELP ME?

  Hello

  I understand your problem in this way.

  You have connected the printer via Port Replicator ports for the A60 SatPro.

  Œuvres driver and so on correctly because the test page can be printed. But when you want to print from Word the printer isn't or what do you mean by "GOGGLEDYGOOK".

  Could you describe a little more detailly and give us some more information like Toshiba shipped OS or MS based installation, Service Pack installed, the name of the printer and so on...

  When you want to validate this information, it would be easier to help you!

  Bob

• Tecra A10 - BSOD with Port Replicator Port and external monitor

  Hello

  I have a Tecra A10 PTSB0A 05C023 with XP SP3 on an Express Port Replicator, running to an external monitor (1280 x 1024) on VGA. Works fine for a while then seems BSOD spontaneously when not in service - possibly when screensaver or powersaver comes into play.

  BSOD is a STOP 0x0000007E in igxpmp32.sys

  I downloaded and installed the latest video drivers intel from the Web from Toshiba - 6.14.10.4953 site

  Any help or advice by eliminating the BSOD would be greatly appreciated.

  Kind regards

  Rhys.

  Hi mate,

  I asked Google to igxpmp32.sys and this file belongs to the Intel display driver. In your case, I recommend the page Intel searching for the latest display drivers.
  [www.intel.com]

  Also have a look on the Toshiba site for a BIOS update, or you have already installed the latest version of the BIOS?

  In addition, it would be interesting to know what Port Replicator you use exactly. Can you post the model number?