printer online 6500 all-in-one printer problems

Similar Questions

• HP Officejet 6500 all-in-One Printer does not send scan and HP print and Scan doctor without help

  HP Officejet 6500 all-in - One Printer does not scan for Windows 7 and HP Print and Scan doctor says 'not imaging' & send error message 8, [1.0,-2147221498)] - I reconnected my officejet drivers reinstalled, etc & nothing works.  I looked for help & tried repeatedly, & am willing to renounce HP.

  Hello

  Thank you for using the HP Forums.

  You can try this alternative solution to Scan:

  HP extended Scan

  FTP://FTP.HP.com/pub/scanners/HPScanExt/HPScanExt.msi

  Once it has downloaded and installed, go to start > all programs > HP > HP Scan extended > Run "HP Scan extended.

  Let us know if it works.

• OfficeJet 6500 E709n: Failure of 6500 all in one ink system

  Recently inherited a 6500 all in one and installed this AM.

  Everything was going fine until I had to print a test page.

  Error: Ink system failure.

  The manual says disconnect power and reconnect after 10 seconds.  This did not help.

  When I ask to print, it says printing the error message and then it makes a grinding noise - in that order.

  Then an error message appears on my pc computer screen.

  This printer has been moved from one House to the other - it would have something to do with the message or the squeaking noise?

  Any suggestions?

  Thank you for your suggestions.

  I had 2 problems: ink system failure and grinding.

  The solution you provided workd partially - that is to say, I can print now but...

  First of all, concerning the failure of the system of ink - the operating manual supplied with the machine to stop the machine, unplug from wall, waiit 10 sec and reconnect.

  I tried and it doesn't work.

  The ground ' n you provided (from HP for the SAME model as my machine) gave another way to reset the machine - turning machine on, unplug the machine, unplug the unit from wall, wait 15 sec, wall plug, machine to reconnect.  In that order.

  Similar, yet very different and IT WORKED.

  So thanks for that.

  But the machine still makes a grinding noise that lasts about 3 seconds.

  I press print, paper flow, paper comes out of the printer, and then there's grinding hard.

  Back then a series of sounds as if something has been reset.

  All very very different from my previous 960C that is turned on when I printed and do not grind or reset of sounds.

  Clues?

• Impossible to scan, fax, or copy of HP Officejet 6500 All-- E709a One in

  I can print from my HP Officejet 6500 All - in - One-E709a, but I can't scan, copy or fax.  All drivers and updates are underway; No recent updates have been made before the problems that occur. I use Windows 7 64-bit.  When the printer is turned on, it still shows Original charge, but no documents are in the charger or on the glass (I already cleaned the glass and have ensured that the lid is tightly).  I have problems to scan, copy and fax. The automatic document feeder works.  I tried to reset the printer several times.

  When I try to scan a document into the document feeder (it feeds through) or from the glass, I get varying answers - rarely, he asked well how I save/handle the doc (e.g., save them in pdf format), but the document does not actually scan and I'm headed to reload the document OR it displays no. Scanning Options. The document does not appear in my analysis.

  When I try to copy, it shows the document as copy, but there is a long delay before the progress bar occurs.  When I copy using the document feeder, I actually get a copy (rarely and always disappeared - looking) or copy prints white - two results are always followed by an error message to reload the document.  When you copy from the glass, the copy print in white with an error message to reload the document

  The same problems occur when you try to Fax.   If trying to scan, copy or fax, the printer does a lot of gears whirring noises.

  Again, I can print a document from my PC without any problem, the problem is limited to scanning, faxing and copying.

  I tried the doctor of printing & scanning HP.  It always stops at the HP Twain scanning stage, saying that the scanning process was cancelled by the user (not true).  When I click on continue, it proceeds to the stage of Test analysis, but nothing happens when I click the button of Scan Test.  It only will allow me to ignore at this point.   All the other steps show green checks.

  My first question is really going to reach the merits of the case, I heard you say that the printer produces noise, but if you lift the bar A) trip through the screen and the light cover B) up?

  In addition, perform both of these resets and I would like to know how they are!

  All-in-one HP printer reset - HP Officejet 6500 - YouTube'

  Have a great day!

• I just replaced all 4 cartridges in my 6500 all in one.

  I just replaced all 4 cartridges in my 6500 all in one.  For all the ink levels are good.  Black ink will not print.  The alignment will fail.  Print test HP troubleshooting page and it was empty.  Suggestions?

  See the post here.

• OfficeJet 6500 all-in-one - black line down page

  Our newly purchased Officejet 6500 all-in-One is the production pages with thin black lines down the page about 2/3 of the way through the page (right side of page).  Is there a solution to this problem?

  This was only happening with ADF.  After several cleanings with no changes, I found this forum.   After reading the plug on the glass, I went back and really clean the glass.  This has allowed the problem.  Thanks for the forum.

• ePrint HP Officejet 6500 All-in-One-Drucker - E709a

  Hello

  Is it possible to use ePrint with HP Officejet 6500 All-in-One-Drucker - E709a?

  Thanks Chris

  Hi Chris,

  The HP Officejet 6500 (e709a) does not support the HP ePrint service, that you will find listed in the following link:

  http://support.HP.com/us-en/document/c03722645

  Kind regards

  Shlomi

• Will be A Officejet 6500 all-in-one printed my pictures from my camera using my sheets of Photo 4 x 6?

  Using Windows 7 64 bit and my all in one HP Officejet 6500 a can print photos from my camera on my HP 4 x 6 photo paper?

  The printer handle sheets of 4 x 6 because I do not see a photo paper tray I had in a previous HP printer all in one?

  Thank you for your help. Websites that recommend you explained what I needed to know.

• My HP Officejet 6500 all-in-one wireless suddenly stopped to print black, even if I have a lot I have

  My HP Officejet 6500 all-in-in-one wireless suddenly stopped printing black, even if I have a lot of ink. It prints all other colors. When I try to check the ink levels it tells me that this printer is not available, try again later. I have a lot of ink. Have restarted printer and Mac Book Pro. Driver is up-to-date. Any thoughts?

  Reset the printer.  Turn the power off and then hold the # and 6 keys during and shortly after turning it on.

• Can not reinstall the software/driver for the Officejet 6500 all-in-one

  I tried to 'day' the pilot on my all-in-one e710n-z printer 6500, and now I have no printer to work at all.  Installation stops at about 80% complete giving the error: Network Installation fails.  I followed all the procedures including online uninstall them, winsock reset, reinstall, install HP utility failure, disabled anti-anti-virus/firewall... nothing works.   My printer is detected by the computer and he "wants" install, but nothing works!  Wi - fi is on, and the only thing that I miss is the driver.  What is the secret of installing the HP online support site?  With the help of Windows OS 8.1.  Thanks for any help!

  Thank you so much for offering to help... This has been a very frustrating experience where I felt like I more, more was wrong.   It turns out that I solved the problem myself with a lot of trial and error and perseverance.  The location of the printer and our computers would not have allowed practical USB or ethernet connection tests.

  The computer has been grateful to the printer, but few of the functions of the printer did not work.  I kept getting notices that I need to be connected to Internet... and yet I was.   Instead, I followed every remedies proposed, and finally met and installed the HP Print & Scan Dr.   The full program would not even install, but I did use uninstall and reinstall the feature on the Dr. P & S and I noticed several MB difference between program he installed and which had been installed until then.

  The error kept showing a network connection problem, but I had already restarted the router several times.  When I got to the printer, I had loaded it a stable and permanent address through the router, so every time I "uninstalled and reinstalled then" software, it always by default the preset number on the router... that has been a blessing!  Finally, I got on the Web site of the real, connected and re-configured router the network connection on the printer using the PIN # that was generated (the WPS buttons had failed earlier) However, it happened, the resumed printer connected and I was able to print a test page.  All is well again.

• HP deskjet all-in-one 3632: problems to make eprint to work

  OK, I'm having a problem making the printer to connect to the internet.

  I have a static IP address on my ISP.   I have 1 n600 Router 2 broadcasting networks.  1 5 g and 2 1. 4 g.   I used void net default 192.168.1.1 and 255.255.255.0.   This router I have a win 7 64 home computer hard wired. I also have a hard wired my Office Access point. the access point also broadcast a GIS of different 2.4 g.  all the sig.s wireless use wap2 Protocol and b/g catch up mode. and the names of all different but same network total network, if that makes sense.  OK, I have a total of 4 more also attached computer too either or network win7 32 ultimate win 7 64 and win vista 32. 2 tablets and 3 IH smrt 5.01 lolipop android running.  I have 2 security cams that have a static for IP and port forwarding on them.  everything works fine.  all computers are part of the same private network hmegroup.  I assigned a static ip address for printer dhcp table.  I can print from any device at any time via wifi.  NOW HERE'S THE PROBLEM.  whenever I go to the WEB form, he is saying that its not active all the check boxes and I don't know what a proxy server is but I know that I have not installed on this network so I click No proxy server.  The PRINTER SAYS UNABLE to CONNECT to the INTERNET.  every time that I tried about 20 this weekend.  It says to check the dns, gateway, blah blah blah.  so the DNS are correct and it shows not 192.168.1.1 as the gateway.  He also btw autodetected it correctly.  so when it fails to connect, I click on web print report. I get the page "get the most out of your printer.  and then a white page. and that's all.  at the top of the page to "get the most out of your printer" it says in "BOLD", "your printer is not connected to a network" which is BS do see on every device and every computer wireless or hard-wire. and I open it a new browser window using 192.168.1.143 which is the static ip address for this printer and bam. It opens right.

  When have I forgotten?  can I configure the gateway as the ip of the real gateway side the ISP of my router.   Im a little aggravated because the only reason why I got this printer from walmart that the PHN android already had the makings of plugin hp on them and I don't like HP is cause of all the fluff sofware that comes with them.  I almost had a gun, but they seem fragile and plasticy more than this one does.  so as I said work is expected for printing on the web.  I tried to press the eprint button and it flashes a little and nothing. I pressed it and the 'i' button and nothing ever prints other than the above page.  I have reset to the default values and done everything as configuration 2 x.

  If anyone can help, I would be very happy.

  facorbin

  Hey @Facorbin,

  Welcome to the Forum from HP Support.

  I see that you are unable to activate the webservices in the all-in-one printer HP Deskjet 3632. I want to help you with this. I have some suggestions that might help.

  I recommend you try the following steps:

  • Enter the IP address in a web browser , and press Enter to go directly to this page. This should take you to your built-in Web server (EWS) printer.
  • Click the network tab.
  • In the submenu on the left, click Networking.
  • Then click on the network (IP) address.
  • Click Manual DNS server.
  • DNS preferred as 8.8.8.8 manual entry
  • Auxiliary DNS server entry as 8.8.4.4
  • Click on apply to finalize this change.
  • Note that menu above EWS items can vary in overall models of printers. If you do not see the exact topics that I've listed here, the subtopic you should always appear on the Networking tab.

  If this goes through successfully, try to activate the web services () again. If you're still coming up short after this point, I recommend you enable DMZ mode in EWS your router, manually add the IP address of your printer. (Based on the level of detail, I suppose you're a statement you know what that means). After completing this step try to enable Web services one last time. Success?

  Please let me know the result of your troubleshooting by responding to this post. If I helped you to solve the problem and that you liked this post, feel free to express your thanks by clicking the "Thumbs Up" icon below by clicking on "Accept as Solution" (this will help others find the solution).

  Thanks for posting in the Forum from HP Support.

  Have a great day!

• HP Officejet 6700: HP Officejet 6700 Premium all in one network problems

  Printer = printer HP e-all-in-one Officejet 6700 Premium
  Model = H711n
  Number of product = CN538A
  Firmware version = MPM5CN1450AR
  Location = Ireland
  Printed pages total: 152
  Scanned pages: 58

  Other details available on request...

  I've had this printer for several months now, I have had no problem connecting to my wireless network and connect computers, telephones and other equipment to this.

  A few days earlier, when starting the printer display flashes with the useless error message, error in the printer, turn the printer off and back on.

  I have power cycled as requested and received the same message, over the power of the cycle he mentions turning off the power button and no DISCONNECT of the sector. Until then I had never disconnected from the sector. After that I have several attempts to power cycle the printer is off and removed the sector, has waited half an hour and powered on again once.

  Still stuck in a loop. He also briefly flashed a blue screen with the error B81431CB. So brief that it is almost useless. I had the boot sequence video and pause playback to read error!

  After some research, I decided that she was experiencing problems connecting to the WIFI network. So, I turned the wifi on the router and the printer network started as usual. Internal menus are now available and I can print status and so forth, so at this point I can exclude defects of ink or mechanism.

  I went in on the printer network settings and reset the network. I'll also through the printer to factory default settings. I have reactivated the WIFI network to the router then went to install the printer again. Digitized for wifi networks and found mine. Entered the password for wifi and the printer could not connect. Everything is good, correct ssid, signal. Report shows wifi password is incorrect.

  I have try several times to connect wifi password is certainly correct, but the printer refuses to recognize the correct password. I tried a different router, the same result. Says incorrect password. Also I tried WPS and a PIN, said still fails to connect.

  At this point, I have disabled all security on the wifi network. Bingo, printer connects to the network, but starts with the loop of error mentioned at the start of the tour and turn it back on. This above has been tried several times, the factory reset, everything ok, turn off the wifi security, the printer connects and goes in a loop.

  So, at this point wifi is confirmed to be defective. I decide to directly connect a LAN cable. Once the LAN cable is connected, a few seconds later the printer detects the network and goes back into its loop error. It will not just connect to a network via wifi or LAN. He previously worked on the network, and nothing has changed on the network, not new parameters or no new devices.

  I connected a laptop to the printer via USB and that seems to work ok, but a USB connection is not ideal and defeated the convenience of a wireless printer. I also tried to reflash the printer in case there is a corruption of the firmware, but the utility detects that the latest firmware is installed and that it is not engaged.

  Now...?

  OK I managed to make it work and I will try to explain the steps of my best.

  As mentioned previously, I tried another router, I tried the wiring, and I tried to reset the router and the printer. Nothing seemed to work.

  Out of curiosity I just put my phone in a WIFI AP. Tried connecting the printer and it worked. The printer connected to the WIFI phones.

  So I know that the printer works on at least one access point.

  Thus, in the settings of the router and firewall. The only thing enabled in the firewall have been

  IPv4 firewall protection

• OfficeJet 6500 all-in-one: Digital Imaging Monitor

  Is it possible to install only the HP Digital Imaging Monitor for the all-in-one printer 6500.

  Or is it possible to find it on my computer.

  I did the complete basic installation and this is, but then I lost it.

  I had to do a full download / install drivers, who worked...

• vertical line on printout of Copier HP 6500 all in one

  ON HP6500 all in one... which copy using the print RDF has a vertical black line.  If I copy with the original on-screen, I don't get the black line.  Seems that the problem is in the document feeder

  Hi sprehedi,

  I understand that you are getting lines when copying. I'll try my best to help you solve this problem. In this document for the vertical stripes, lines or streaks in the Copies, faxes or Scans , he explains where is glass and the rollers need to be clean.

  I hope this helps, let me know if you need more assistance.

  Thank you

• HP Officejet 4355 all-in-one: scanning problems

  The Scan option does not appear on my computer despite having installed the all-in-one HP Officejet 4355 printer. I also tried to download the latest drivers for the printer but the Scanner does not work. Yet on other laptops (I have a Gateway laptop), there is no problem, the analysis option is available.

  Is there a compatibility issue when using the printer on Vista?

  Hello

  Please download and run the HP print and Scan Doctor www.hp.com/go/tools