Satellite C650-17Z: (new!) startup repair problem

Similar Questions

• Satellite C650-17Z - only PXE error message no boot device

  Hi people I was wondering if anyone of you kind people out there could help me. I have a Satellite C650-17Z model and when turn on is the message I get:

  + Intel UNDI, PXE - 2.0 (builkd 083) +.
  + Copyright (C) 1977-2000: Intel Corporation.

  + For Atheros PCIE Ethernet Controller v2.0.1.9(12/15/09) +.

  + Check the cable connection! +
  + PXE - MOF: exit Intel PXE ROM. +.
  + No boot device - insert boot disk and press any key.

  Can anyone any sense of the message above?

  Hey Buddy,

  This error message means that an incorrect boot order is set and the computer tries to start between LAN port to the internal HARD disk space. It should therefore go into BIOS setup and change the boot order. Put the HARD drive as the first boot device internal.

  Take a look at this article from Toshiba:
  [PXE error message appears during the clean boot procedure | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=8]

• Satellite C650-17Z - keys FN and Ctrl-Alt-Del does not work

  I recently bought a Satellite C650-17Z and the function key and the Ctrl-Alt-Del key combination ceased to operate. Is there a solution to this all - I got older laptops from Toshiba is a driver issue, but I can't find the drivers for specific keyboard on the Toshiba site.

  Could someone enlighten me, please?

  Hello

  Regards the FN keys will find it many other topics in the forum.
  Did you find them? Is there a solution for you?

  In any case, you must reinstall the package of added value and utility to Support Flash Cards because both controls the FN keys. You can download all the tools on the official website of Toshiba:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  But for the Al-Ctrl-Del combination, there is no special driver but maybe it can be solved with these tools...

• startup repair problem.

  I have an acer aspire 5920 equipped Windows vista and only recently, it has had problems with the start up. whenever I turn on the laptop Startup Repair guard arise and checks the system for problems. After a few minutes its says "windows cannot repair this computer automatically" and "If you have recently attached a device to this computer, like camera or portable music player, remove it and then restart your computer...". "When I cliquerai finish it again the whole process.
  I tried running on safe reboot of the last good configuration mode. and it starts repairing appears again.
  Help, please. Thank you.

  As the system restore does not work, try this:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  As your grave in the category above, download the ISO on the link provided and make a bootdisk of it.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.

  You can do a system restart tool, system, etc it restore.

  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If this fails, the Acer Recovery Options:

  http://www.acerpanam.com/Synapse/forms/portal20.cfm?RecordID=853&formid=3390&website=AcerPanAm.com&siteid=7117&words=all&keywords=&areaid=2

  Acer eRecovery made

   

  1. on the Acer splash screen, you can press Alt and F10 (at the same time press F2 to enter the BIOS) to make it appear a version BACK style eRecovery.

  ·        The unit is able to reload Windows from this mode faster then CD.

  ·        The default password is 000000 (6 zeros) and it is shown when you are prompted for the password.

  ·        Users are able to change the password in this mode for eRecovery only.

  ·        The system can retrieve the hidden on the hard disk (partition PQService) image or a CD/DVD media.

  ·        It is possible to reload the factory CD/DVD style or snapshots that creates the eRecovery Windows version.

  2. in Windows, there are 3 ways to access eRecovery functionality.

  ·        Press Alt and F10

  ·        Open Acer eManager and then double-click eRecovery.

  ·        When a system is new it should automatically open this application and invite you to do the recovery media.

  See you soon.

  Mick Murphy - Microsoft partner

• Startup repair problem - uwvwg.sys

  Computer Acer with vista... maybe not of course 32-bit

  Please bear with my long history

  When I start my computer, I get the Startup Repair... no matter what I do same in SafeMode or who were previously working mode settings or what it's called.

  It all started with a stop... which means that I held until the ignition button it closed because of my suspended computer itself.

  Then he started a loop of startup repair no matter how many times man I fix my computer it always starts the computer with startup...

  So I went to aid navigation. I tried to boot from the cd/dvd to install vista and repair from here, nothing...

  Then I saw a few posts that said he might have hardware problems and I need to contact acer... I tried to run several test to cehck if there is no hardware problem, but all the tests said no... tried something advanced startup repair, something called something memtest and also seatool if I remember correctly...

  Then I found some info on the use of cmd with commands like bootrec.exe... didn't work so I tried a last thing before that wierder

  • bcdedit/export C:\BCD_Backup
  • c:
  • Boot CD
  • BCD attrib s h - r
  • Ren c:\boot\bcd BCD.old
  • Bootrec /RebuildBcd

  obtained from http://support.microsoft.com/kb/927392/en-us

  He rel screwwed my computer completely now, when I boot my computer without disk vista installation everything I get is a black screen with the text

  File \windows\system32\drivers\uwvwg.sys

  Status 0xc0000225

  Something important the driver file is damaged or missing.

  And then I tried to repair by there with my vista... instalation disks Startup Repair I then checked that the report of the repair and he could fix everything but this file uwvwg.sys error 0x2

  I also tried to do a reostre system to a previous point, but it seems my computer isn't everything.

  Is my last resort completely re-installing windows vista? I can't go directly to windows 7 same with my computer in this State? and always keep my files in c: drive?

  Please help... Thank you

  Yes. Here's how to recover data from a disk hard when you can't get to Windows:

  1 remove the drive and put it in a box of USB drive or use a USB adapter. Attach it to a computer that is running a working XP/Vista/Windows7 installation. Use the work of Windows Explorer to copy the data to the hard drive of the system to the rescue and burn data on cd or dvd, or copy it to an external hard drive. I prefer not to do it if I know the drive is infected because he has a chance to infect your host system. In these cases, I use #2 below.

  2. you can start the computer target with a Bart PE (XP only) or Linux Livecd such as Knoppix or Ubuntu and retrieve the data in this way. This has the additional advantage to tell you if the problems you are experiencing are hardware or software related because if the computer behaves perfectly in Linux, you know that Windows (software) is the culprit. Conversely, if the computer behaves badly under Linux, you will know that there is a hardware problem. This is general information on the use of Knoppix for the recovery of data when you do not have Windows:

  You will need a computer with two cd records, one of which is an engraver of CD/DVD OR a USB thumb drive with enough capacity to contain your data OR an external USB hard drive. Download Knoppix .iso image file and create your bootable CD *. If you do this in a previous (XP or Vista) operating system, you will need the third burning like Nero, Roxio or freeImgBurn software (Windows 7 can burn .isos natively). Burn as an image, not in the form of data. Then boot with the CD that you created and the Windows files will be visible under Linux. If you want to burn CD/DVD, there will be a Linux burning program to use.

  * If your computer has only an optical drive and you want to use this drive to burn data or need to test drive, you can create a USB bootable Linux instead of a bootable CD. This site will show you how to do it-http://www.pendrivelinux.com

  http://www.Knoppix.NET
  http://www.nu2.nu/pebuilder/ - Bart PE Builder

  See also - http://lifehacker.com/5504531/the-complete-guide-to-saving-your-windows-system-with-a-thumb-drive
  http://www.howtogeek.com/HOWTO/17044/move-files-from-a-failing-PC-with-an-Ubuntu-Live-CD/
  https://help.Ubuntu.com/community/LiveCD and for future disaster recovery programs - http://www.elephantboycomputers.com/page2.html#Backing_Up

  MS - MVP - Elephant Boy computers - don't panic!

• Satellite L350D - crashes on startup repair screen

  Laptop Toshiba L350D my GF had a funny turn and was served on the screen of the tool to RESTART SYSTEM a few days now.

  I doing nothing it can make this screen, I F8 would be up to my bleeding fingers, when to choose anything safe mode the display returns to the STARTUP REPAIR and do its thing.

  It will not start and crashes right on the screen of the Startup Repair tool.

  I don't have a recovery disc Toshiba, what can I do?

  Thanks in advance

  Well I think that if you are not able to go into the advanced boot menu (F8) and so if you can start t HARD drive recovery works you have the Toshiba recovery disc.

  As I see you don t have it and if you order a disk Toshiba directly:
  https://backupmedia.Toshiba.EU/landing.aspx

  I know it's strange, but I think that in this case, you can t anything.

• Satellite C650-17Z collection problem

  Hi, I'm recovering a laptop Toshiba friends, it has a recovery partition, but unfortunately I can't make it work. I tried to start the process of disk recovery HARD by turning on the computer laptop and holding down the key 0 or F8 but no work after the Toshiba logo gets it right on the next screen and continually bleeps

  other ways to start the recovery?

  Hello

  If the recovery of HARD drive does not work, you will need to use the recovery disc.
  But it seems that recovery disk does not have to be created in the just past?

  Well, in this case, you can order the CD here:
  http://backupmedia.Toshiba.EU/landing.aspx

• Satellite A60 found new hardware wizzard problems

  Hi, I am the owner of a Satellite a60 laptop I recently formatted my hard drive with windows xp because I have done what I have problems with the new found hardware wizzard.on, try to install the software for my i - pod and bt travel 1065 PC laptop wireless adapter that I get the text next message "new hardware wizzard." found it impossible to install this material the hardware was not installed because the wizard cannot find the necessary software"in this case, even when the cd is in the drive could you possibly tell me what could be the cause could there be a missing driver?

  Hello

  Unfortunately I didn t try to still configure the i - pod, but try to activate the option check the CD directly or check if maybe some setup.exe file is available on the CD and it must be installed before connecting external devices.

• DELL startup repair problem

  Hello. Right now, my problem is with my Dell laptop. I tried to do a factory restore. After awhile, I got a pop window that says "error". Now whenever my computer starts, it goes to the start screen for repair. I use the F8 option on reboot, but it always ends up back here. All proposals/solutions would be great.

  Hello

  Here's how the dell recovery process should work

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

  Above is Dell to reinstall Vista from the DVD on your computer.

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=336966

  And that way if you have a recovery partition on your hard drive.

  ___________________________________________________________________

  If you have problems with the process of recovery of manufacturers, contact the manufacturer

  It's their recovery process not microsofts

  Dell support

  http://support.Dell.com/

  Dell Support Forums

  http://en.community.Dell.com/support-forums/default.aspx

• Re: Satellite C650 - some keys do not work normally

  Toshiba Satellite C650 series, reinstalled Windows 7, problem with the keyboard, some keys do not work normally, some keys are intchanged... for example. the sign @ is located above the right shift key but now the types of the '2' i.e. the SHIFT key functions of these keys are reversed... the same with other keys 2-3... What is the problem? How to solve it?

  Thank you & best regards

  You have preinstalled Windows using original recovery image, you got with your laptop (Win7 preinstalled Toshiba)?
  I ask this question because I want to know if the keyboard is compatible with the language of the OS.

  Have you tried to change the keyboard input language?

• Re: Satellite L650 stuck Startup Repair mode

  Hello

  I was asked to look at the Satellite L650 laptop for a friend because they could not get going.
  Not sure they did before me do yesterday, as far as I know, it's that they couldn't turn it on. I wanted to get into Safe Mode, but it went to the Startup Repair Mode and is stuck in this at all times.

  It is currently running Windows 7 Home Premium 64-bit.

  Have you tried from the DVD player, but it is up to the use of the hard drive, even tried running in my network, but without a bit of luck.

  It does not go to the repair step because it gives me the opportunity to enter a password.

  Someone at - it ideas how I can work around this problem, you can.

  HAL

  Hello

  I think you have only two options here:
  (1) you are going to use HARD drive recovery options
  (2) or you can start the recovery using the recovery disk

  For HARD drive recovery:
  http://APS2.toshiba-tro.de/KB0/HTD1303440001R01.htm

  Recovery disk:
  A friend created one in the past?
  Isn't it? Well, the new disc can be ordered here:
  http://backupmedia.Toshiba.EU/landing.aspx

• Satellite C650 composed a series of beeps during startup

  Bought new Satellite C650 laptop for daughter, managed to establish a wireless connection and load anti virus soft wear.
  Laptop is now a series of beeps during the startup process after you log with password and before loading windows. Bleeps last about 10-15 seconds and count 20-30 constant beeps.

  What this mean and how can I stop them?

  Hey Buddy,

  This means that Windows does not start correctly and you can enter the password but it beeps again for 10-15 seconds?
  Well, that s very strange

  If so, you are using the version preinstalled Windows from Toshiba or did you install your own version of Windows?

• Satellite A200-J01: Startup Repair cannot repair computer automatically

  Hi all

  I can't get my laptop to start. I am currently traveling overseas and
  I was hoping that someone may have met or know of this problem.
  It has always worked well and the only thing I did everything differently when using the laptop here is you connecting to the internet to /cafes of hot spots and watch DVDs (copies pirated in Bali) so I was wondering if any of them can cause this problem of startup repair.

  When you turn it on it tells me that...

  "Startup Repair is checking for problems of system" then...

  "Startup Repair cannot repair this computer automatically.

  When I look to see what the details of the problem, it's that I get...

  Problem event name... "StartupRepairV2.
  Fallback 6.0.6000.16386.6.0.6001.1800
  6
  786444
  Corrupted volume
  no cause root

  I appreciate any comment beforehand, as I am now carting round a laptop dead!

  Thank you

  First of all, it would be interesting to know something about your laptop. What model of laptop do you have?
  Have you tried starting in safe mode using the F8 key?

  Some new notebook series is equipped with HARD drive recovery. IF you can try to press the F8 key immediately after you have switched on the laptop, then choose fix my computer and try the laptop recovery

• Temporary solution to load problem with Satellite C650

  I here provide a temporary solution to loading with Satellite C650 problem, which I have faced.

  First of all, I've updated my BIOS. After that, I removed the battery and plugged AC for 2-3 minutes.

  Then replace the battery and it loaded.

  However, the battery got charged up to 99% only and after that the interrupted load and the load remained at 99% and renewed battery indicating "plugged in, not charging."

  Therefore, each time I hv to repeat the procedure above to charge my battery.

  If any1 has the solution to the prob. above, it would be gr8 to hear.

  Thank you very much!

  Thanks for your posting.
  To be honest I really don t know what else you can expect and test it with new battery.

  I think that your laptop model must always have a warranty valid, right?
  If so, contact Toshiba nearest service provider and ask for replacement.

• Satellite C650 - battery problem

  Hello

  I've got this Toshiba Satellite C650 about a friend who gave me it reinstall Windows7.

  Before you reinstall, I noticed that the laptop has not activate on battery. When I pluged the charger he started and it started once ran on battery without any problem. Also, when it is turned on and that the charger is removed the battery icon do not show how much time left and show unknown time remaining in place.

  When I reinstalled Windows does not solve the problem.
  I've updated the BIOS, but still does not solve the problem.
  I started to think that it's a hardware problem.

  The laptop is new - age one month.

  I'll be very grateful if someone could help me or point me to the solution of this problem.
  The laptop is still under warranty, but I decided to ask here first and here are some other opinions.

  Thank you!

  Try this:
  Remove and disconnect the battery and the AC adapter.
  Now let and don t touch the laptop for some time (2-3 hours)
  Then press and hold the power button / stop along 30 sec.

  Now connect the battery and the AC adapter and keep it charge until the battery indicator would turn to green (or blue)
  Then turn on the unit and check how it works.

  PS: its always recommended to calibrate a new battery, that means that the battery should be completely discharged and recharged until 100% was achieved.
  This procedure should be repeated several times in the line