Toshiba Libretto L5 / 80 - driver screen and battery problem

Similar Questions

• gauge the battery to the boot screen and battery on report menu conflicting Details about the level of the battery. The gauge from the battery to the Starter incorrectly displays the low battery level that prevent the macbook pro battery retina start

  gauge the battery to the boot screen and battery on report menu conflicting Details about the level of the battery. The gauge from the battery to the Starter incorrectly displays the low battery level that prevent the start of the battery. This happens on macbook pro retina 13 inches

  When I try to startup macbook pro retina in battery mode, it will fail to start showing low battery level and an indicator to recharge the battery. It does not start on battery. When I then connect via the power cable at startup (and check the battery level), monitor of battery in the menu bar indicates that the battery is charged to the top.

  It gets really frustrating and remove my ability to use the macbook pro retina as a truly portable device...

  Appreciate any help on this

  Have you tried resetting the SMC? Reset the management system (SCM) controller on your Mac - Apple Support

• Toshiba Satellite A215-A4757 black screen and unable to initialize

  Received the black screen after trying to download the update of the BIOS; has been logged in as administrator, but received the error 'need to be logged in as an administrator. Could not go further. Process had not begun restore point then minimized and tried to validate the connection as an administrator. Locked screen and got a black screen with errors about bad driver. Doesn't seem to be valid. In any case, I liquidated - power off. Does not power on f11 or any other key - cannot start. Keyboard seems dead. seeing lights to drive DVD could perhaps start with the startup disk. However, do not have (not too smart). Is there a way to get a system of information-based boot disk? I had a previous assignment but did not because months ago. Thanks for any help/suggestions.

  Perhaps your message to: http://forums.toshiba.com/?

• Satellite L650-1EQ - black screen and overheating problems

  Hello

  I have a problem with my laptop Satellite L650-1EQ.
  A few days ago my laptop was overheated quite often.
  I would like to start playing a video game and the computer could actually turn off after 10 minutes of playing it.

  I realized that this was getting serious so I stopped using my computer to play games and I decided that I need to clean it. However, I was looking for online on how to clean up my computer and then my screen turns white!

  I didn't know what happened and was very scared.
  I turned off the computer.

  The next day I turned on the computer to see if it was good, and the screen was black however the laptop power light comes on and I hear the vents work.

  I turned on the computer and tried to start it again, and the computer started fine.
  The image appeared and the problems disappeared.
  But I knew that something bad was about to come so I took the laptop computer repair technician.

  I told her what happened.
  He has used the vacuum to "clean" the dust of the computer and told me to go back if the computer kept a overheating.

  I restarted the computer again when I came home, and after an hour and a half the computer screen turns white but I don't think that it overheated. : s

  I tried to start the computer and the screen is black, no picture, the only light on is the power one and I hear the vents work. I tried of transformed market but now it just stays as if it were now.

  I tried on another computer for solutions such as the battery and pressing the power button for 2 minutes and other things, but nothing has worked. I don't know what to do so I decided to create a thread to get answers: s

  Please help me, thank you!

  PS: I'm sorry for my English, I know that's not the best

  Hello

  This does not sound very good boyfriend. I'm afraid that there could be some sort of dysfunction material Mr. something like the problems of graphics card or motherboard issue.

  You can try plugging the external monitor to the laptop just to see if something would be visible on 2nd screen.
  But if nothing will appear on the 2nd monitor, I think that the chip of the graphics card died :(

  Of course, this is just my personal opinion and a laptop computer technician must check the laptop to know what part of the laptop could be faulty.

• Windows 10 place 8 Pro (5830) Orientation, driver, Boot and camera problems

  I've had problems with camera for a while now. When I try to open the camera application, I get a message that the camera is not connected. I tried to solve this problem through different methods, none of which work, and all of a sudden, I start getting a problem of Orientation.

  A few days earlier, I tried to start, and the machine would only start in Portrait mode. Tilt, rotation, etc. would not alter orientation. I went into the settings and was able to make the meeting place in the landscape, and he should stay there until the next time I started. It always starts in a Portrait, a direction that I rarely use.

  I thought that my problem was perhaps a pilot and I checked the Device Manager. All seemed well. Then, I went to the Dell Support and ran the driver verifier. They told me that I needed to update the Chipset Intel Atom Z3000 Series driver, so I started the download. The download is finished and the machine began to install it. Almost immediately, I got the error that the "Installation failed." I tried again and again, failed.

  Then I looked in the Device Manager to see if I could find where this driver fits, thinking that I could remove the driver in the machine and it would be automatically installed. After carefully by the Device Manager, I found the driver.

  Either incidentally... at some point earlier today, I might not even the machine to start. It froze on the screen, you get before the login screen. About 15 restart attempts finally worked and the machine will start up again.

  I then tried to reset the Tablet and received an other error message that it could not be done.

  I'm in a world of pain, here. Any suggestions?

  OK, no responses, so here is my solution...

  I've broken down and decided to follow the hard way... to the format of the drive, then reinstall Windows 10 and all software. It's a great job. The first thing is to gather all the material needed to make this work.

  Necessary material:

  1. an adapter Dell to allow the power supply and USB connection full size at once. I have a Dell for $20.

  2. a USB Hub with a minimum of 4 entry slots.

  3. USB keyboard

  4. USB mouse

  5 USB Wireless Network adapt

  6 USB Windows 10 32-bit Installer

  7. a lot of Patience.

  Connect the USB Hub to the Dell adapter (1) and insert line electric adapter Dell, attach it to the tablet in the mini (or is this microphone?) USB port.

  Hold the switch and the Volume until you pass at the same time until the Tablet starts in the BIOS. Change the boot order using the Volume button upwards so that the tablet will boot from USB Windows 10 Setup and follow the instructions.

  Once win 10 installed, make sure that you have a wireless connection, and go to the Dell Support to download and install the Driver.Your Chipset coming 8 Pro should now allow touch screen and Orientation. Download and install no matter what other drivers you need and all your software. Set up and you're back in business.

  Wow, that took me 6 hours, but all works, now including my camera

• My computer Toshiba Satellite keeps the 'blue screen' and that is to say that it is caused by "a problem with a USB driver. How can I fix it?

  Resolve a problem with a USB driver

  You have received this message because your universal serial (USB) bus driver caused a stop error, also known as a blue screen error. This error means that the computer has stopped abruptly to protect against potential corruption of data or loss.

  What is a driver?

  A driver is software that allows your computer to communicate with hardware or devices. Without drivers, the hardware you connect to your computer (for example, a video card or a webcam) may not work properly.

  The recommended steps that follows can help to eliminate this problem, or at least reduce its frequency. Try them in the order listed. If a step cannot solve or reduce the problem, then move on to the next.

  Steps to fix this problem

  1. Adjust your computer's power settings

     The following power settings may help reduce the frequency of this problem.

     1. Turn off the USB selective suspend setting:

        1. Click on the Start button .

        2. In the search box, type power options, and then press ENTER.

        3. Find the plan selected, and then click change plan settings.

        4. Click change advanced power settings.

        5. Double-click the USB settings , and then double-click on USB selective suspend setting.

        6. Make sure that the USB selective suspend setting is disabled. If it is enabled, click it and select disabledand then click OK.

     2. Disable power saving mode (computer portable computers only):

        1. Click on the Start button .

        2. In the search field, type power options, and then press ENTER.

        3. Under Preferred Plans, ensure that High Performance is selected, and then close the window.

  2. Look for an update of the BIOS for your computer system

     Several computer manufacturers whose computers have this problem published BIOS updates to fix this known issue. Contact your computer manufacturer to see if a BIOS update is available for your computer model.

     What is the BIOS?

     The basic input/output system (BIOS) is software built into a computer that runs when the computer is turned on. Among other things, this software starts the operating system, and supports the transfer of information between hardware devices (such as the keyboard and the monitor).

     How can I find the manufacturer of my computer?

     Click on the Start button , type msinfo32 in the start search box and press ENTER. The manufacturer of your computer is listed as the manufacturer of the system in the right pane of the system information window.

     Click here to go online to see the contact information for most of the computer manufacturers

  3. Download and install the latest updates and drivers for your computer

  It's a good idea to periodically check the updates of driver for your computer, especially if you added new hardware recently, such as a USB hub or other USB device.

  What is a USB hub?

  A USB hub is a device with multiple (USB) universal serial bus ports. USB ports are narrow and rectangular connection points to connect USB devices to your computer. A USB hub is used an Extender of port or port replicator, providing more USB ports to run from a USB connection on your computer. USB hubs can be external devices that connect to a USB port, or they can be internal devices built into your computer.

  To check for driver updates:

  1. Use Windows Update to find and install updates:

     1. Go online to Windows Update

     2. Click the check for updates in the left pane, and then click view available updates.

        What happens if I see any updates available?

        • If you see you receive updates: managed by your system administrator, you can try clicking on the link to check online for updates from Microsoft Update or Search online for updates from Windows Update, but you should maybe contact your system administrator to get the desired updates.

        • If you do not see the message above and no update is available in Windows Update after clicking on the link check the updates in the left pane, then the available updates have already been installed.

     3. Select the driver for your device updates and more updates to install.

        Note
        We recommend that you install all Important updates and recommended. These updates improve the security and stability of your computer.

     4. Click on install. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  2. If you recently added a new hardware device on your computer, go online to the manufacturer's Web site to see if there is an update to the driver.

  3. If you recently added a new program on your computer, go online to the manufacturer's Web site to see if an update is available.

  Steps to work around this problem

  Warning
  These measures are intended to solve a specific problem, but could do so by temporarily disabling or removing some features on your computer.

  1. Try to remove newly added USB devices

     If this issue occurs after adding a USB hub or other USB device, consider removing to see if the problem goes away. If this resolves the problem, contact the manufacturer of the device for the updates or other recommendations.

  2. Do not disconnect USB devices while the computer is to stop or go to sleep

  This problem is known to occur when USB devices are disconnected when the computer is trying to stop or switch mode to 'sleep'. This is common with cell phones, especially those with a docking station, as docking station can act as a USB hub. The frequency of this problem could be reduced by allowing your computer to completely close or completely in sleep mode before detached from its docking station or unplug it or the docking station USB devices.

  If you know which USB device is causing the problem

  It may be possible to prevent the Blue error screen by choosing the option remove the device safely in the Notification area, before putting your computer into sleep or Hibernate mode.

  1. In the system tray, click the icon to remove the device , select the USB device that you think that the origin of the problem and then click OK.

  2. Do not physically remove the USB device.

  3. Perform the action which resulted in the Blue error screen, so that was taken the functioning of your computer after the mode standby, hibernation, or, in the case of laptops, close the laptop computer or place it in a docking station.

     1. If the Blue error screen persists, it is likely that the problem is with another USB device. Try this procedure using other USB devices until you find that at the origin of the problem.

• If the Blue error screen disappeared, you have probably identified the device causing the problem. Contact the manufacturer of the device for more information on how to solve this problem, or use the option to remove the device safely to work around him.

Note
Depending on the manufacturer and model, some USB devices will become available automatically when you resume using your computer. Others will require that first disconnect you physically and then plug back in front, they will be recognized by the computer. Check the system tray to see if the USB device that you removed safely become available when you started to use your computer again. If she did not become available automatically, then physically unplug it and then plug it in again.

This is the screen it gives me. Help, please! If problem fixed, will BE AWARDED!

Hi ChayceSteffiare,

For instructions on solving problems with USB devices, see the following article:

Tips for solving problems of USB devices

To fix blue screen errors, see the following article:

Pick up the pieces after a computer crash

See also:

Optimize Windows Vista for better performance

Ways to improve your computer's performance

• Toshiba Satellite problem model # PS181L - T 03, 07, drive HARD and CD problem

  My friend has a toshiba satellite, I don't know if he has a problem of room, it starts on a diskette.

  The problem is that it cannot detect the CDROM and the HARD disk drive.

  What can be the solution to this, thank you.

  BTW, what is the way to reset the CMOS in parameter by default.

  Thank you.

  Hello

  I'm not sure of the solution to the problem, but you can enter the BIOS by pressing the ESC key when you feed the PC.

  BR

  Tom

• New hard drive, installed Windows XP PRO version 2002 - resolution screen and internet problems

  My Dell has had some problems (patially due to age), so a buddy of mine and I put a new hard drive in it and then installed windows XP Pro.  Installation went great, but now that it's installed, I can not get the screen resoultion to change and I can't connect to the internet.  I feel like with the internet, can I have a driver problem.  I know that the internet works, I'm on it with the laptop right now.  Any suggestions?

  ????  I'm not sure I understand your question. You download the drivers to a place, you will find them, as the office. If you want to put them on a USB stick, copy the files downloaded to the key and take it to the computer target. Copy the files on the computer desktop. Double-click on a file and it will unpack the installation routine starts. Follow the installation wizard. Reset when said to repeat as needed until all the drivers, etc are installed. Subsequently, you can delete the downloaded files from Dell (from installation .exe). MS - MVP - Elephant Boy computers - don't panic!

• Screen and battery

  Hi, I got my Xperia Z2 for over a week now and I noticed a few spots or patterns on the screen when it is exposed to the Sun or other bright light (the screen display of the Z2 in the direct light of the Sun is simply superb), it's a little tedious and boring, is the screen of the Z2 really like that? (it shines / shines under the direct light of the Sun)
  As well, since I've updated to 4.4.4 Kitkat, the battery performance was all just bad even if it is in standby mode now that I couldn't last more than 7-8 hours on a single charge. Finally, it is taking me 4 hours or more to completely load the phone with a battery drain and no, I don't use any cable or Charger 3rd party adapter. The I use EP880 adapter and cable micro usb EC803.
  Did someone experienced this problem since upgrade to 4.4.4?

  Hi, the model that you see is the digitizer & quite normal so nothing to worry about

• Satellite Pro P100 - screen and sound problems after upgrade to Windows 7

  Hi all

  I got my Satellite Pro P100 (model number is PSPAEE-00C006EN and the second digit of the serial number is '7') upgraded from Vista to Windows 7, and since then, some bugs seem to have had place - can someone help me on the following:

  -L' screen DIMS increments, irrespective of the fact that I have saved my power settings to stay on FULL (battery or sector)

  -No sound. Once or twice, the sound card worked and settings to say this works correctly (and you can see the movement of the graphic equalizer).
  In terms of PC knowledge, I would be 5/10 (so not a dummy, but certainly not a pro! and we tried a lot of the more obvious things)

  Thank you all

  Hello

  1.) if the screen dim option doesn't properly work, I recommend you to reinstall Toshiba Value added Package. This package controls these functions, the keys FN and others. Visit the Toshiba page for an update!

  2.) did you check if the sound is muted if the equalizer work? In addition you can also try to update the audio driver might it work ;)

• Satellite A210-103 and battery problem

  I have an A210-103:
  HTTP://DE.COMPUTERS.TOSHIBA-EUROPE.COM/INNOVATION/JSP/SUPPORTSECTION/DISCONTINUEDPRODUCTPAGE.DO?SERVICE=DE&PRODUCT_ID=1 33099 & DISC_MODEL = 1
  and I bought a new battery 9 cells:
  http://www.Amazon.de/GP/product/B000RSQX6U/ref=oh_o00_s00_i00_details
  but the battery works only 150 minutes. Where can I find some info for the best performance. the old battery was 6 cells.

  only 150 minutes?
  How long it should run on battery?

  In General for this model of laptop 2 hours of uptime a pile of food is quite good.
  Time to market better? Reduce the power consumption of equipment using power saving options.
  Have you tested it already?

• Adapter sector and battery problem?

  I recently bought an Equium M40X - 149 and when the power adapter is connected to the laptop it does not use its power, it only uses battery power. When I take the battery it uses alternating current. I thought it was strange, because I think he should charge the battery, and the power of the computer.

  I removed the battery and was just running back into the computer on AC power and decided to put the battery and the computer says that he was using AC power but also to charge the battery. However, this lasted a few minutes and returned to the use of the battery, even if it was only 83% charged.

  Could someone help me on this issue.

  See you soon

  Hi Gemma,

  The maintenance of power system is integrated on the motherboard. This allows the notbook control the battery even when the notbook is turned off.

  The symptoms you describe indicate a problem with the power jack, or maybe a touch loose connector AC causing propulsion to misbehave.

  I suggest you contact your Agent of Service Toshiba authorized closest because that will be covered by your warranty. The nearest your Agent details can be found on the Toshiba web site.

  HTH

• HP Envy 6z-1000 screen and bezel problem

  Hello

  I bought my HP Envy 6z-1000 in October 2012. Since almost two years, I managed to avoid a fall or scratch, and performed reasonably well - apart from overheating, the weird sticky key and this strange feature that whenever I stop, it seems to insist the program is on and I have to force to close...

  In any case, I just opened the lid of the laptop and heard a disturbing cracking-click sound. Somehow the lower right corner of the bezel take the case and screen together, right side of the hinge, jumped out. I can pop back together again between my fingers, but there not together, jumping out again whenever I open and close the lid.

  How this issue contain them? What should I do?

  Thank you

  Charles

  I just sent you a private message. If you are unsure how to check your messages from the forum, this post has instructions.

• Dell Inspiron 1525 Wireless and battery problems

  Hey! So, I recently dug my old laptop, a Dell Inspiron 1525.

  When I started it, it's horrible and basically endless sequence of beeps. Then finally he started on. Battery says "plugged in, not charging" and when unplugged the computer turns off. The Wireless does not work. I tried the switch on the side, and I tried to install the drivers from the drivers disk and a USB port with the updated drivers, I got from Dell. The wireless is not working. I have re-installed Windows Vista 32-bit. (The default OS) and still no luck.

  Any thoughts? Anything I should try? Thank you. :)

  Hello

  To get the deleted password BIOS you will need to contact Dell Technical Support.  We cannot do that here on the forums.  You will need to contact them (probably by telephone) and be able to verify ownership of this system in order to reset the password for them.  They will ask you things like the name and address of the shipping system was initially sent, the name of the owner (in archives), etc.

  If you don't know that information you can go to the online form for change of ownership of the American (he has a link to the international on this page if necessary) and the system of re-registration in your name in our system.  If you do not have this information, you will need to contact the original owner to get it, or call our Technical Support team and they will be able to give you a better idea of what they need.

  Reset / flashing the BIOS will allow this system to "see" the card if it is not currently (and until the card works).   Which should allow drivers, etc., will be installed, which theoretically should allow you to get out of the internet with the wireless connection.

  Todd

• 9800 torch Touch Screen and Trackpad problem

  Our application adds buttons only on devices that support the touch screen.

  The reason why we do this is because if you have a selected item in a list field and press the getSelectedIndex returns the correct index on a touchscreen.

  Add this button on a trackpad/trackball device would not work properly because you can't the selected list box item and then click the button. You need to scroll this button first, the getSelectedIndex in this case would be the first clue or the last index according to the place where the button.

  If anyone has a solution or suggestions please post. I'll also post updates and a solution if I find one.

  We had the same problem when we added a toolbar style touch the foot of some screens that contains a list field.

  Our solution: vertical movement of pointer changes the selection of the list, while the horizontal movement jumps down to the toolbar, but leave the current selection in the list where it is.

  May not work for your particular application, but seems to be accepted in our.