VPN3015 + Cisco VPN Client 3.1 - IPSEC connection problems.

I have set up a VPN3015 and am using 3.1 Client on a Windows 2000 laptop. Dial my ISP and you connect through the client. I get a message "peer remote no longer" on the client. 3015 journal display the message "filter on interface 1, data missing peers x.x.x.x IKE dropped."

I have the filter set to '- None -' in the 'general' tab of the configuration of the group. I created an IKE and a company monitoring and makes sure they use pre-shared keys. I checked that the group name and the password on the client matches the 3015.

Any help or ideas would be appreciated.

Marv

Marv

You MUST have a filter defined on the interface to which you are connected through otherwise, you get the above message.

The filter is selected using a downs drag in the configuration of the Interface. The filters were created (from memory) somewhere of in policy management of-> traffic management.

Start by using the private network filter that allows any and then start to restrict once you have all this work.

I hope this helps. Regards, Barry

Barry Hesk

Network Manager

Notability solutions

Tags: Cisco Security

Similar Questions

  • Cisco VPN Client is blocking incoming connections

    Hello

    I somethimes (not always) a problem with the Cisco VPN Client.

    As soon as the CISCO VPN Client is installed (it must not be running) it blocks inbound connections from the local network.

    The problem is that I use Ultra VNC SC to support some of my clients. Another client is supported by Cisco VPN. With UltraVNC SC customer clients try to connect to my PC.

    But if I installed the cisco VPN Client, no incoming connections are possible.

    How can I change this behavior?

    This behavior is not always the same. Last incoming connections of two months were possible, but from one day to another is not possible more.

    I recently installed the Client, but it takes no effect :-(

    I have NOT activated the firewall Cisco on the VPN Client and the behavior is NOT only if the Client is activated. This is the behavior even if it is NOT active and just installed.

    Hi Chris,

    Zone alarm is installed on the PC that is defective?

    Try to restart the Cisco VPN service and launch the vpn client.

    I remember having a similar problem with the Cisco VPN Client. Some conflict between the VPN client and Zone-Alarm, installed on the same PC.

    The problem was with VSDATANT variables in the registry key.

    Please see the following mail took from another forum:

    http://www.OutpostFirewall.com/Forum/showthread.php?t=9917

  • Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

    Hello

    I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

    I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

    Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

    Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
    Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

    The router configuration

    IKE policy

    VPN strategy

    Client configuration

    Hôte : < router="" ip=""> >

    Authentication group name: remote.com

    Password authentication of the Group: mysecretpassword

    Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

    Username: myusername

    Password: mypassword

    Please contact Cisco.

    Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

    You can use the PPTP on the RV180 server to connect a PPTP Client.

    In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

  • Cisco vpn client is supported on the analogue ppp connection

    can someone pls tell me if we can use the client vpn cisco on a ppp connection analog and put a pix that is not PPPs running. If it works, then why do we need to VPN L2tp/ipsec. can someone pls tell me something abt it. It is very urgent.

    concerning

    Assane

    Assane,

    If I understand your question, you speak with PPP initially to get an IP address from your service provider, then use the Client VPN VPN in your Pix Firewall. If so, yes it is possible.

    To name a few reasons why PPTP or L2TP/IPSEC is used instead of Cisco VPN Client are:

    1. because companies have used a PPTP or L2TP/IPSEC solution for some time and are migrating to Cisco VPN

    2. do not install vpn on the PC client software

    3. won't pay for the VPN Client software licenses

    Let me know if it helps.

    Kind regards

    Arul

  • Cisco VPN Client and Windows XP VPN Client IPSec to ASA

    I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.

    PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?

    Config is:

    !

    interface GigabitEthernet0/2.30

    Description remote access

    VLAN 30

    nameif remote access

    security-level 0

    IP 85.*. *. 1 255.255.255.0

    !

    access-list 110 scope ip allow a whole

    NAT list extended access permit tcp any host 10.254.17.10 eq ssh

    NAT list extended access permit tcp any host 10.254.17.26 eq ssh

    access-list extended ip allowed any one sheep

    access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh

    sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0

    tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0

    flow-export destination inside-Bct 192.168.1.27 9996

    IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0

    ARP timeout 14400

    global (outside-Baku) 1 interface

    global (outside-Ganja) interface 2

    NAT (inside-Bct) 0 access-list sheep-vpn

    NAT (inside-Bct) 1 access list nat

    NAT (inside-Bct) 2-nat-ganja access list

    Access-group rdp on interface outside-Ganja

    !

    Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2

    Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1

    Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1

    Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1

    Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1

    Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1

    Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1

    Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1

    Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1

    dynamic-access-policy-registration DfltAccessPolicy

    Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

    Crypto ipsec transform-set newset aes - esp esp-md5-hmac

    Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans

    Crypto ipsec transform-set vpnclienttrans transport mode

    Crypto ipsec transform-set esp-3des esp-md5-hmac raccess

    life crypto ipsec security association seconds 214748364

    Crypto ipsec kilobytes of life security-association 214748364

    raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

    vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1

    card crypto interface for remote access vpnclientmap

    crypto isakmp identity address

    ISAKMP crypto enable vpntest

    ISAKMP crypto enable outside-Baku

    ISAKMP crypto enable outside-Ganja

    crypto ISAKMP enable remote access

    ISAKMP crypto enable Interior-Bct

    crypto ISAKMP policy 30

    preshared authentication

    3des encryption

    md5 hash

    Group 2

    life 86400

    No encryption isakmp nat-traversal

    No vpn-addr-assign aaa

    Telnet timeout 5

    SSH 192.168.1.0 255.255.255.192 outside Baku

    SSH 10.254.17.26 255.255.255.255 outside Baku

    SSH 10.254.17.18 255.255.255.255 outside Baku

    SSH 10.254.17.10 255.255.255.255 outside Baku

    SSH 10.254.17.26 255.255.255.255 outside-Ganja

    SSH 10.254.17.18 255.255.255.255 outside-Ganja

    SSH 10.254.17.10 255.255.255.255 outside-Ganja

    SSH 192.168.1.0 255.255.255.192 Interior-Bct

    internal vpn group policy

    attributes of vpn group policy

    value of DNS-server 192.168.1.3

    Protocol-tunnel-VPN IPSec l2tp ipsec

    Split-tunnel-policy tunnelspecified

    Split-tunnel-network-list value split tunnel

    BCT.AZ value by default-field

    attributes global-tunnel-group DefaultRAGroup

    raccess address pool

    Group-RADIUS authentication server

    Group Policy - by default-vpn

    IPSec-attributes tunnel-group DefaultRAGroup

    pre-shared-key *.

    Hello

    For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.

    Please see configuration below:

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

    or

    http://tinyurl.com/5t67hd

    Please see the section of tunnel-group config of the SAA.

    There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.

    So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.

    Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.

    "crypto isakmp nat-traversal.

    Thirdly, change the transformation of the value

    raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

    Let me know the result.

    Thank you

    Gilbert

  • Cisco vpn client to connect but can not access to the internal network

    Hi all

    I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network

    Any help would be much appreciated.

    Hi Samir,

    I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

    (The link above includes split tunneling, but this is just an option.

    Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.

    Let me know if this can help,

    See you soon,.

    Christian V

  • Cisco VPN Client 5.0.0 does not connect

    Hello

    I am trying to establish the VPN session the firewall to 5525 X Cisco ASA crossing 9.1.1 Cisco VPN Client. Although AnyConnect is the way to go, the inherited method must always be supported for some time as part of a migration. I tried two VPN users (authenticated by ad) on two client computers running Windows 7 64 bit and Cisco VPN Client 5.0.07.0440. Both users are able to establish a session to a computer at the ASA, but not the other. Entering credentails evil, the login popup will appear immediately. On the combination of username/password correct name, the following VPN client log messages are generated and the session drops that is "not connected" in the status bar. The PCF file is the same on both client computers.

    Cisco Systems VPN Client Version 5.0.07.0440
    

    Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
    

    Client Type(s): Windows, WinNT
    

    Running on: 6.1.7601 Service Pack 1
    

    119    22:49:16.933  06/23/13  Sev=Info/6          IKE/0x6300003B
    

    Attempting to establish a connection with 203.99.111.44.
    

    120    22:49:16.939  06/23/13  Sev=Info/4          IKE/0x63000001
    

    Starting IKE Phase 1 Negotiation
    

    121    22:49:16.942  06/23/13  Sev=Info/4          IKE/0x63000013
    

    SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 203.99.111.44
    

    122    22:49:16.973  06/23/13  Sev=Info/5          IKE/0x6300002F
    

    Received ISAKMP packet: peer = 203.99.111.44
    

    123    22:49:16.973  06/23/13  Sev=Info/4          IKE/0x63000014
    

    RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from 203.99.111.44
    

    124    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
    

    Peer is a Cisco-Unity compliant peer
    

    125    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
    

    Peer supports XAUTH
    

    126    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
    

    Peer supports DPD
    

    127    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
    

    Peer supports NAT-T
    

    128    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
    

    Peer supports IKE fragmentation payloads
    

    129    22:49:16.977  06/23/13  Sev=Info/6          IKE/0x63000001
    

    IOS Vendor ID Contruction successful
    

    130    22:49:16.977  06/23/13  Sev=Info/4          IKE/0x63000013
    

    SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 203.99.111.44
    

    131    22:49:16.977  06/23/13  Sev=Info/6          IKE/0x63000055
    

    Sent a keepalive on the IPSec SA
    

    132    22:49:16.977  06/23/13  Sev=Info/4          IKE/0x63000083
    

    IKE Port in use - Local Port =  0xCA7C, Remote Port = 0x1194
    

    133    22:49:16.977  06/23/13  Sev=Info/5          IKE/0x63000072
    

    Automatic NAT Detection Status:
    

    Remote end is NOT behind a NAT device
    

    This   end IS behind a NAT device
    

    134    22:49:17.000  06/23/13  Sev=Info/5          IKE/0x6300002F
    

    Received ISAKMP packet: peer = 203.99.111.44
    

    135    22:49:17.000  06/23/13  Sev=Info/4          IKE/0x63000014
    

    RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
    

    136    22:49:17.211  06/23/13  Sev=Info/4          IPSEC/0x63700008
    

    IPSec driver successfully started
    

    137    22:49:17.211  06/23/13  Sev=Info/4          IPSEC/0x63700014
    

    Deleted all keys
    

    138    22:49:23.207  06/23/13  Sev=Info/4          IKE/0x63000013
    

    SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
    

    139    22:49:23.393  06/23/13  Sev=Info/5          IKE/0x6300002F
    

    Received ISAKMP packet: peer = 203.99.111.44
    

    140    22:49:23.393  06/23/13  Sev=Info/4          IKE/0x63000014
    

    RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
    

    141    22:49:23.393  06/23/13  Sev=Info/4          IKE/0x63000013
    

    SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
    

    142    22:49:23.401  06/23/13  Sev=Info/5          IKE/0x6300005E
    

    Client sending a firewall request to concentrator
    

    143    22:49:23.401  06/23/13  Sev=Info/4          IKE/0x63000013
    

    SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
    

    144    22:49:23.427  06/23/13  Sev=Info/5          IKE/0x6300002F
    

    Received ISAKMP packet: peer = 203.99.111.44
    

    145    22:49:23.427  06/23/13  Sev=Info/4          IKE/0x63000014
    

    RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
    

    146    22:49:23.427  06/23/13  Sev=Info/5          IKE/0x63000010
    

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 10.2.193.69
    

    147    22:49:23.427  06/23/13  Sev=Info/5          IKE/0x63000010
    

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 10.2.5.2
    

    148    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x63000010
    

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 10.1.5.2
    

    149    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
    

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000000
    

    150    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
    

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
    

    151    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000F
    

    SPLIT_NET #1
    

    subnet = 10.0.0.0
    

    mask = 255.0.0.0
    

    protocol = 0
    

    src port = 0
    

    dest port=0
    

    152    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000E
    

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = example.org
    

    153    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
    

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
    

    154    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000E
    

    MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5525 Version 9.1(1) built by builders on Wed 28-Nov-12 11:15 PST
    

    155    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
    

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
    

    156    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
    

    MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
    

    157    22:49:23.445  06/23/13  Sev=Info/4          IKE/0x63000056
    

    Received a key request from Driver: Local IP = 10.2.193.69, GW IP = 203.99.111.44, Remote IP = 0.0.0.0
    

    158    22:49:23.445  06/23/13  Sev=Info/4          IKE/0x63000013
    

    SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 203.99.111.44
    

    159    22:49:23.477  06/23/13  Sev=Info/5          IKE/0x6300002F
    

    Received ISAKMP packet: peer = 203.99.111.44
    

    160    22:49:23.477  06/23/13  Sev=Info/4          IKE/0x63000014
    

    RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from 203.99.111.44
    

    161    22:49:23.477  06/23/13  Sev=Info/5          IKE/0x63000045
    

    RESPONDER-LIFETIME notify has value of 86400 seconds
    

    162    22:49:23.477  06/23/13  Sev=Info/5          IKE/0x63000047
    

    This SA has already been alive for 7 seconds, setting expiry to 86393 seconds from now
    

    163    22:49:23.477  06/23/13  Sev=Info/5          IKE/0x6300002F
    

    Received ISAKMP packet: peer = 203.99.111.44
    

    164    22:49:23.477  06/23/13  Sev=Info/4          IKE/0x63000014
    

    RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:NO_PROPOSAL_CHOSEN) from 203.99.111.44
    

    165    22:49:23.478  06/23/13  Sev=Info/4          IKE/0x63000013
    

    SENDING >>> ISAKMP OAK INFO *(HASH, DEL) to 203.99.111.44
    

    166    22:49:23.478  06/23/13  Sev=Info/4          IKE/0x63000049
    

    Discarding IPsec SA negotiation, MsgID=F3E3C530
    

    167    22:49:23.478  06/23/13  Sev=Info/4          IKE/0x63000017
    

    Marking IKE SA for deletion  (I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65) reason = DEL_REASON_IKE_NEG_FAILED
    

    168    22:49:23.478  06/23/13  Sev=Info/5          IKE/0x6300002F
    

    Received ISAKMP packet: peer = 203.99.111.44
    

    169    22:49:23.479  06/23/13  Sev=Info/4          IKE/0x63000058
    

    Received an ISAKMP message for a non-active SA, I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65
    

    170    22:49:23.479  06/23/13  Sev=Info/4          IKE/0x63000014
    

    RECEIVING <<< ISAKMP OAK INFO *(Dropped) from 203.99.111.44
    

    171    22:49:24.310  06/23/13  Sev=Info/4          IPSEC/0x63700014
    

    Deleted all keys
    

    172    22:49:26.838  06/23/13  Sev=Info/4          IKE/0x6300004B
    

    Discarding IKE SA negotiation (I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65) reason = DEL_REASON_IKE_NEG_FAILED
    

    173    22:49:26.849  06/23/13  Sev=Info/4          IKE/0x63000001
    

    IKE received signal to terminate VPN connection
    

    174    22:49:26.855  06/23/13  Sev=Info/4          IPSEC/0x63700014
    

    Deleted all keys
    

    175    22:49:26.855  06/23/13  Sev=Info/4          IPSEC/0x63700014
    

    Deleted all keys
    

    176    22:49:26.855  06/23/13  Sev=Info/4          IPSEC/0x63700014
    

    Deleted all keys
    

    177    22:49:26.855  06/23/13  Sev=Info/4          IPSEC/0x6370000A
    

    IPSec driver successfully stopped

    Any ideas why the second client of Windows 7 does not work?

    Kind regards

    Rick.

    Rick

    Thanks for the additional output. It shows the xauth authentication step, which is good to see. But it does not offer much clarity on what is causing the problem.

    My attention is drawn to a couple of message on the balls that are in line with the two sessions for which you posted newspapers.

    32 00:36:08.178 24/06/13 Sev = Info/5 IKE/0x6300005E

    Customer address a request from firewall to hub

    I'm not sure that we see any answer to this, but it makes me wonder if it is somehow involved in the issue. Is it possible that there is a difference in the configuration of firewall and operating between two clients?

    I am also interested in this series of posts

    48 00:36:08.210 24/06/13 Sev = Info/4 IKE / 0 x 63000056

    Received a request from key driver: local IP = 10.2.193.69, GW IP = 203.99.111.44, Remote IP = 0.0.0.0

    I don't know why the pilot requested a key at this point, and I wonder why the remote IP is 0.0.0.0?

    It is followed by a package in which the ASA provides the value of the life of SA - which seems to be on the path to a successful connection. that is followed by

    55 00:36:08.350 24/06/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = 203.99.111.44

    56 00:36:08.350 24/06/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

    during which the SAA indicates that no proposal has been selected. It seems therefore that the ASA is not happy about something.

    If we do not find indications of the client that allows to identify the problem, then maybe we look at the ASA. Are all log messages generated on the SAA during this attempt to establish VPN that could show us the problem? Would it not be possible to run debugs on the SAA in a trial of this machine?

    HTH

    Rick

  • Unable to connect via the Cisco VPN Client

    Hello

    I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

    I am not able to connect and watch the journal on the SAA

    ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

    ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

    ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

    What could be the reason.

    Concerning

    Hi, I had this same problem, here is the solution:

    When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

    Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

    Well, change your strategy using MD5 isakmp / OF would do the trick.

  • PIX: Cisco VPN Client connects but no routing

    Hello

    We have a Cisco PIX 515 with software 7.1 (2). He accepts Cisco VPN Client connections with no problems, but no routing does to internal networks directly connected to the PIX. For example, my PC is affected by the IP 172.16.2.57 and then ping does not respond to internal Windows server 172.16.0.12 or trying to RDP. The most irritating thing is that these attempts are recorded in the system log, but always ended with "SYN timeout", as follows:

    2009-01-06 23:23:01 Local4.Info 217.15.42.214% 302013-6-PIX: built 3315917 for incoming TCP connections (172.16.2.57/1283) outside:172.16.2.57/1283 inside: ALAI2 / 3389 (ALAI2/3389)

    2009-01-06 23:23:31 Local4.Info 217.15.42.214% 302014-6-PIX: TCP connection disassembly 3315917 for outside:172.16.2.57/1283 inside: ALAI2 / 3389 duration 0:00:30 bytes 0 SYN Timeout

    2009-01-06 23:23:31 Local4.Debug 217.15.42.214% 7-PIX-609002: duration of disassembly-outside local host: 172.16.2.57 0:00:30

    We tried to activate and deactivate "nat-control", "permit same-security-traffic inter-interface" and "permit same-security-traffic intra-interface", but the results are the same: the VPN connection is successfully established, but remote clients cannot reach the internal servers.

    I enclose the training concerned in order to understand the problem:

    interface Ethernet0

    Speed 100

    full duplex

    nameif outside

    security-level 0

    IP address xx.yy.zz.tt 255.255.255.240

    !

    interface Ethernet1

    nameif inside

    security-level 100

    172.16.0.1 IP address 255.255.255.0

    !

    access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.2.56 255.255.255.248

    !

    access extensive list ip 172.16.0.0 outside_cryptomap_dyn_20 allow 255.255.255.0 172.16.2.56 255.255.255.248

    !

    VPN_client_group_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.255.0

    !

    IP local pool pool_vpn_clientes 172.16.2.57 - 172.16.2.62 mask 255.255.255.248

    !

    NAT-control

    Global xx.yy.zz.tt 12 (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 12 172.16.0.12 255.255.255.255

    !

    internal VPN_clientes group strategy

    attributes of Group Policy VPN_clientes

    xxyyzz.NET value by default-field

    internal VPN_client_group group strategy

    attributes of Group Policy VPN_client_group

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list VPN_client_group_splitTunnelAcl

    xxyyzz.local value by default-field

    !

    I join all the details of the cryptographic algorithms because the VPN is successfully completed, as I said at the beginning. In addition, routing tables are irrelevant in my opinion, because the inaccessible hosts are directly connected to the internal LAN of the PIX 515.

    Thank you very much.

    can you confirm asa have NAT traversal allow otherwise, activate it in asa and vpn clients try again.

    PIX / ASA 7.1 and earlier versions

    PIX (config) #isakmp nat-traversal 20

    PIX / ASA 7.2 (1) and later versions

    PIX (config) #crypto isakmp nat-traversal 20

  • Unable to connect using the Cisco VPN client

    Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

    I enclose the relevant configuration information in the attachment. Any help is welcome.

    Depending on the version, add...

    ISAKMP nat-traversal

    or

    ISAKMP nat-traversal crypto

    Should be all you need.

  • Slow initial connection using Cisco VPN Client

    I am currently using Cisco VPN Client v5.0.07.0290.  Whenever I start my connection, it takes me about 90 seconds for the prompt to display authentication and another ~ 90 seconds to finish the auth. and connect successfully.  I have another computer laptop w / the same WIN7 OS and version of Cisco VPN Client and he ends the connection to<30 sec. ="" why="" is="" this? ="" any="" suggestions="">

    Hi Sergio,

    You import the .pcf for the VPN Client file? If so, please try to recreate a new file .pcf locally on the machine itself and try to connect. Let me know how it goes.

    Thank you

    Delvallée

  • connect Cisco VPN client v5 to asa 5505

    I have remote vpn configuration issues between ASA5505 and Cisco VPN client v5. Successfully, I can establish a connection between the client Vpn and ASA and receive the IP address of the ASA. Statistical customer VPN windows shows that packets are sent and encrypted but none of the packages is received/decrypted.

    Cannot ping asa 5505

    Any ideas on what I missed?

    Try adding...

    ISAKMP nat-traversal crypto

    In addition, you cannot ping the inside interface of the ASA vpn without this command...

    management-access inside

    Please evaluate the useful messages.

  • IPSec site to site VPN cisco VPN client routing problem and

    Hello

    I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

    The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

    There are on the shelves, there is no material used cisco - routers DLINK.

    Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

    Can someone help me please?

    Thank you

    Peter

    RAYS - not cisco devices / another provider

    Cisco 1841 HSEC HUB:

    crypto ISAKMP policy 1

    BA 3des

    preshared authentication

    Group 2

    ISAKMP crypto key x xx address no.-xauth

    !

    the group x crypto isakmp client configuration

    x key

    pool vpnclientpool

    ACL 190

    include-local-lan

    !

    86400 seconds, duration of life crypto ipsec security association

    Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

    !

    Crypto-map dynamic dynmap 10

    Set transform-set 1cisco

    !

    card crypto ETH0 client authentication list userauthen

    card crypto isakmp authorization list groupauthor ETH0

    client configuration address card crypto ETH0 answer

    ETH0 1 ipsec-isakmp crypto map

    set peer x

    Set transform-set 1cisco

    PFS group2 Set

    match address 180

    card ETH0 10-isakmp ipsec crypto dynamic dynmap

    !

    !

    interface FastEthernet0/1

    Description $ES_WAN$

    card crypto ETH0

    !

    IP local pool vpnclientpool 192.168.200.100 192.168.200.150

    !

    !

    overload of IP nat inside source list LOCAL interface FastEthernet0/1

    !

    IP access-list extended LOCAL

    deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

    deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

    IP 192.168.7.0 allow 0.0.0.255 any

    !

    access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

    access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

    !

    How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

    Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

    DE:

    access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

    access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

    TO:

    access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

    Also change the ACL 190 split tunnel:

    DE:

    access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

    access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

    TO:

    access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

    access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

    Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

    Hope that helps.

  • Using Cisco VPN Client in Windows 7 Professional 64 bit

    Hi all!
    I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem

    Open the XP VM itself, do not use the shortcut that was published in
    the W7 boot menu. You need to install Outlook / your email client
    Inside the virtual machine, as well as on the side of W7. You can point to the same
    PST files if you have local PST files, but you just can't open them in
    at the same time of W7 and XP VM.

    There is no way to bridge using the shortcut of publishing app

    Some people have reported success with the third party IPSec
    replacements as customer universal shrew or the NCP. Your IT Department.
    would like to know if these are supported

    :

    > Hello all! I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem
    Barb Bowman www.digitalmediaphile.com

  • SafeNet and Cisco VPN Client Compatible?

    I have been using the Cisco VPN for quite awhile with no problems. Recently, we have added a Watchguard Firebox somewhere else and have installed the Client of Watchguard MUVPN, otherwise known as a customer of Safenet.

    Since the installation, I could not yet properly use the Cisco Client. If I disable the two Services of Safenet, I invited to my user id and password and connect to the Cisco Concentrator and get an ip, etc. However, I can't ping anything on the network.

    My solution is to completely uninstall both clients and reinstall the Cisco by itself. This is not very practical.

    If anyone know a fix for this I'd appreciate comments.

    Thank you

    Patrick Dunnigan

    Hi Patrick,

    I only got lucky with the SafeNet customer brand Watchguard with the 4.0.x releases of the Cisco client. I think Cisco 4.6 clients use a newer driver from the DNE or else that plays well with SafeNet.

    In any case, here's how to set up PC that requires both clients:

    First, install the Cisco VPN client. Restart the application, and then stop and disable the Windows service.

    Install the client for Watchguard, reboot as requested.

    Then, stop and set to manual both SafeNet services, then start and set to automatic the Cisco service.

    Delete the shortcut in your Start menu Startup group safecfg.exe (or the key of HKLM\MS\Windows\CurrentVer\Run, where he gets set.)

    Delete the shortcut to start for the Cisco VPN client as well.

    Whenever you want to use the Cisco customer, you can just launch the Dialer to IPSec. If you want to run the SafeNet client, stop the Cisco service, start the services of SafeNet, then run safecfg.exe. A few batch files facilitate this process for users.

    Hope that helps,

    Chris

Maybe you are looking for

  • Strange behavior when searching from the address bar

    Hi all! I tried to remove google as the default search provider in firefox. To do this, I did these two things- -Duckduckgo moved to the top of the list in the firefox search box and set it as the current research. -Put the URL 'https://duckduckgo.co

  • Skype error 'instruction privilege. "

    Hello I have a problem with my Skype. As soon as I turn it on, it crashed (work stoppage). I uninstalled and reinstalled, but it still does not work. Now, I get the message "the privileged instruction" as the reason why it has stopped working. What i

  • Satellite M70 Wireless problem persists

    Now, I tested my wireless a few weeks with the latest drivers Intel and I also set on max PSP.I still sometimes have waiting periods. Especially when there are a lot of load on network bandwidth. How about other users? Especially users Laurent0001 an

  • A chart of the wave axis cannot change automatic formatting

    See attached photo and vi. I can change the other two y-axis floating-point, but I can't change the "acceleration x, y, z" automatic formatting floating-point; whenever I click on floating point, the highlight goes to the automatic formatting. Now wh

  • Cannot read my emails on hotmail

    I have Windows XP and for the last month on my account, I was unable to read any e-mail simply triangle icon and with errors on page load it now affecting my wifes account what happens with hotmail