Questions/problems new today Lenovo Y70 network and touchpad

Similar Questions

• HP Color LaserJet M277n MFP: HP Color LaserJet MFP M277n, no problems with scan to folder network and internet connection.

  I just bought a 277n MFP which I am running wireless. I have problems with:

  1 - the printer is connected to the internet (no problem connecting to the network and printing)

  2 - definition of networks for scanning file (this is how this problem started because I tried to update the firmware)

  1.

  Searched the forum and found some good articles. Tried to restart and change the DNS as shown without success. Other means?

  2. follow-up guide how to set up an SMB shared folder, but without success.

  I shared "\\Johans-MacBook-Pro\users\johan\documents" under OSX and did the same thing in the printer web setup. Even tried with the entrance of my user name and password. When I press 'save and test' I don't have that "the test failed. Try again. »
  Any suggestions?

  Best regards

  Johan

  Hi @Johan84,

  You can use DHCP or an IP fixed, but you will need to set the DNS.

  Disable the IPv6 setting on the printer.

  Go to the printer settings.

  Configuration of the network.

  Network services.

  IPv6.

  Turn the power off.

  These steps should help with scanning to email.

  Let me know. Thank you.

• Lenovo y70 touch and windows 10

  I don't have 10 windows on my touch of y70 enovo. The icon is not apear on my desktop why?

  How can I get windows 10?

  Dear cinquefoil

  Welcome to the community of lenovo,

  Please make sure that your windows is activated and that you have installed the latest updates of windows 8.

  Otherwise, you can use the link below to download the windows 10 media creation tool

  https://www.Microsoft.com/en-us/software-download/Windows10

  Thank you for using the community of lenovo.

• How can I connect to the internet? Problems involving the network and sharing Center does not.

  Hello.
  I live in a House and bought a range extender so that I can get a connection in my basement as well.  I have installation range Extenders without problem.  When you install the range extender, I changed my name to my network router.  I changed the name of the network by typing 192.168.1.1 in my browser.
  The MacBook connects without a problem.  In the basement, the connection of Windows 7 works very well.  I have just connected Vaio Windows 7 my mother to the network, but it prompted that I enter the user credentials.  I read a post above and got that problem solved by opening the network and sharing Center and adding a new connection.  Now that the connection is configured correctly.
  The problem is with the laptop HP Windows Vista family basis.  Since I install the range extender, I can't connect to the network.  He had no problems before you connect the router or other networks to visit other places.  The new network name appears, but when I click it, it says I have to enter the user credentials.  I tried to manually, but the name is taken so I can't make a new and invites me to connect to the network that is established or to connect to a different network.
  • I tried to open the network and sharing Center, but it does not open.  When I click it, it opens a screen for a brief second.  The option "Display the status of network and tasks" opens either.

  • I logged as an Administration by entering the command line < net="" user="" administrator="" ctive:yes=""> > and restarted the laptop.  Even logged in as administrator, this folder does not open.

  • I also did a scan < sfc="" cannow=""> >.  The digitized rolled up with an error, but the error has been corrected.

  • I also updated the connection of the range extender.

  Why the network and sharing Center will not be open to the top?
  How can I configure my router my HP Windows Vista Linksys connection?
  Thank you.  Please let me know if you need more information.

  Thanks for your reply.

  In a last attempt, my sister has used the ethernet cable to connect directly to our router.  Next time, she turned on her laptop, she managed to connect to our wireless network and she was not invited to enter credentials.
  In this case, the manual connection helped solved the problem.

• I'm trying to set up a wireless network and it is said that something does not work with the driver.

  Hi there tried to hook my laptop up to wireless as ethernet cable keeps me tripping. I am complete technophobe and propably have the only laptop that gets used especially to open the door.

  Have tried everything I can think even threaten her with glass of water after trying to connect to the wireless network, that it is said that there is something that doesn't work not with the driver if it means something to you. I have a toshiba, if it helps.
  Thank you
  original title: I hope someone can help technophobe

  It is said that there is something not working only not with the driver

  You probably need to install some network drivers for your wireless card.

  Download drivers

  Visit the manufacturer's Web site and select your computer model (this is usually done in the Support section). You should be able to download drivers for your model. Download the driver (s) and follow the instructions to install - every computer is different, so I can't give you exact directions. You can also try to use Windows Update to get drivers - it is located in the start menu.

  Update of the hardware driver that is not working properly:

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Establishment of a network domestic:

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-home-network

  For more information network:

  Start here to set up a home network in Windows 7:

  http://Windows.Microsoft.com/en-us/Windows7/start-here-to-set-up-a-home-network-in-Windows-7

  What do I need to connect to Internet:

  http://Windows.Microsoft.com/en-us/Windows7/what-do-I-need-to-connect-to-the-Internet

  Adding a wireless computer

  Set up a wireless network:

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  If your network is wireless, run the wizard to Set Up a network on the computer attached to the router.

  1. open Set Up a network by clicking the Start button, then Control Panel. In the search box, type network, click Network and sharing Center click on set up a new connection or a network and then click on set up a new network.

  2. the wizard will guide you in the process of adding other computers and devices to the network. For more information, see:

  http://Windows.Microsoft.com/en-us/Windows7/add-a-device-or-computer-to-a-network

  Manually add a wireless computer

  1. sign the computer.

  2 open the connect to a network by clicking the network icon in the notification area.

  3. choose the network wireless from the list that appears and then click on connect.

  4. type the network security key or password if you are prompted to do so, and then click OK.

  -You will see a confirmation message when you are connected to the network.

  5. to confirm that you have added to the computer, follow these steps:

  -Open network by clicking the Start button, then Control Panel. In the search box, type network, and then, under center network and sharing, click on view network computers and devices.

• Pavilion DM1-4000sd keyboard and touchpad not working not

  Hello

  I'm back from holiday yesterday and when I tried to power on my laptop that he had to go through the windows recovery. Normally this wouldn't be a problem, but it seems the keyboard and touchpad are not working in windows or recovery recovery screens / normal boot selection screen. Also I can not access my bios (not), so this is most likely related to the same problem.

  The laptop was working fine before and I've never had any keyboard / touchpad editions.

  What can I do to fix this?

  Problem solved, plugged a mouse usb and it worked in the recovery menu. Still confused but on how I'll never get into the bios...

• HP Officejet Pro 8500 A909a USB 3 questions about the configuration of the network - port USB3 problem

  Fujitsu Windows 7 laptop (all USB2)

  used the full software and installed a printer HP Officejet Pro 8500 A909a Series as a network printer.

  The printer installed fine and don't have USB connection

  All the software and scanning twain installed, so I was able to scan the copy etc.

  I could browse and choose my PC from the front panel of the printer

  However, it was Tuesday confirmed to a friend that their printer would work on a new laptop - bought the laptop

  Fujitsu - but more recent model with 3 USB ports

  I have install and then used the same FULL configured driver to be installed (V14)

  selected as a network printer and then, during the installation, I get an error hardware error USB and USB drivers

  All the USB works, that I've used - BUT the printer is networked and no USB used

  tried to download the driver and install it-exactly the same question

  SO I configure using the devices and printers 'add printer' network and installed

  I can print OK

  BUT no analysis facilities

  and on the façade - cannot see the new PC to scan to

  The only real difference, is that this PC has USB3 and only mine has USB2

  DO not know why on a network installation USB even when searching for

  It's a problem because Drivet package not has not been updated for USB3 - y at - it a patch?

  Thanks for any help / advice

  Hi etaf,.

  I guess the short answer is: Yes, the problem with the software and the 3.0 Port.

  The long answer with a possible work around is as follows: first of all, the software looks for minimum requirements. Because the software is older, he doesn't know what a 3.0 port. You are right when you say that it should work since you do not use the USB and use wireless instead, but this is not the case.

  There is something we can try, but I can't guarantee it will work. I thought first we could connect a USB cable and run the software made to force the software to see the USB port, but then the software wouldn't even get far enough because you can't plug the cable to the most later in the installation.

  My second thought and most promising suggestion is to connect the USB cable (although we do normally not until the software prompts us to) and use the installation wizard HP Print to get the insteaad of software to use the CD or download from the printer driver page. Still, I can't say with certainty that it works, but I don't see why it would not be worth a try.

  If it works, and we get the software installed you can convert the USB connection to a wireless connection using the software. Fingers crossed! Download and run the with the following link. Printer HP install wizard for Windows

  If this does not work, or you don't want to bother with it (not worth trying), I might consider getting a new model of the printer. You can even call HP. They might be able to offer a discount on a newer model. If you are in the Canada, U.S. dial 800-474-6836 or you can Contact HP worldwide.

• Laptop HP 15-go99er: problem with network and WiFi

  Hey guys,.

  Does anyone know to solve this problem? I recently installed a new windows on my laptop and since then I can see is more available connections. I went to Device Manager and these drivers seems to have problems

  "Network controller"

  PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C & REV_01
  PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C
  PCI\VEN_168C & DEV_0036 & CC_028000
  PCI\VEN_168C & DEV_0036 & CC_0280

  ""PCI Device"

  PCI\VEN_1022 & DEV_1537 & SUBSYS_15371022 & REV_00
  PCI\VEN_1022 & DEV_1537 & SUBSYS_15371022
  PCI\VEN_1022 & DEV_1537 & CC_108000
  PCI\VEN_1022 & DEV_1537 & CC_1080

  Can anyone help, because I can't seem to find the proper drivers.

  Hello:

  For the wireless card, this driver should work...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-127981-1 & CC = US & DLC = in & LC = on & os = 4158 & Product = 7174407 & sw_lang =

  For the E/D PCI controller, this driver should work, but you may need to install manually if auto installation does not work.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=vc_136254_1

  If it does not automatically install, go to Device Manager and click the controller PCI E/D in need of drivers.

  Click the driver tab.  Click on set to update driver.  Select Browse my computer for driver software option and find the folder of the driver that was created when you ran the file.

  This file will be located in C:\SWSetup\sp66899.  Make sure that the include subfolders is selected and the driver should install.  Then restart.

• Satellite C850 - found problems with the networking and the FN key

  Hey everybody,

  I work on a Satellite Toshiba C850, that my parents recently bought and spin in a certain number of questions.

  (1) wireless won't connect to my network. Have done the following: verified by connecting on two other computers, reset the router, the open network, reset the map, reinstalled the realtek drivers, checked the settings in the networking of Toshiba Utilities. End result is he's going to try, and fail. Wired LAN works fine.

  (2) FN key does not work. Have you checked the region and it is OK, have tried to use the Flash cards - no change, checked with the screen keyboard and can check the FN key does not register.

  I noticed that the first problem is common, but there are obvious positive results. If anyone can offer any assistance, I would appreciate it a lot.

  Before you begin to discuss your problems can you please tell us what OS you are using?
  Are you using the original OS that you got with your laptop? I mean original recovery image has been tested and works correctly, with the factory settings that all should especially the FN keys.

  1 / What do you mean with refusing? your WLAN is visible for your laptop?

  2 / if there is problem with the feature keys FN and you use Win7 try please reinstall extra package from Toshiba.

• Problem network and restore do not work.

  I have a computer that I used throughout the past two years.  I have programs on it to keep and I also have pictures and emails, I don't want to lose.  I don't know it's a software problem, I know because I bought another hard drive identical to the one I had installed inside and reloaded windows Xp and drivers everything works fine. I noticed that the last night, I used this PC when I went to turn off windows indicates there is a notification of update, I went ahead and let him do his thing the next day is when the problem manifested itself to the power upward.  I tried to immediately restore no good just stop. The next thing I noticed is that there no Favorites showing network, my ethernet went, my card controller spent, wireless no internet connectivity at all.  My question is - what the machine starts fine and a files seem normal y at - it an easy solution for this without completely formatting and reloading windows so I won't lose my programs I do not have access to the original disks to recharge?

  Hello

   
  1. What are the updates that have been installed recently?  Provide us with the number of these updates?
  2. What is the brand and model of the computer?
  3. you receive an error running the system restore?
   
   
  Method 1:  Try to perform a restore of the system into safe mode with command prompt.
  How to start the System Restore tool by using the option of safe mode with the command prompt in Windows XP
  http://support.Microsoft.com/kb/304449
  
  If this does not help, you can consult this article to troubleshoot the System Restore tool.
  http://support.Microsoft.com/kb/302796
   
  
   
  Method 2: Wi - Fi and in Windows network connection issues
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows?T1=Tab03
   

• Problem with wireless - Vista Network and Sharing Center does not recognize my connection!

  I use the Home Visa software and my network and sharing Center does not recognize my connection but I can access the internet without any problem. Previously, I was using a wireless router Linksys with an old box of AT & T internet with no problems. The problems started after I updated my AT & T internet box that made obsolete the linksys router and now the network share does not connect. I just have the problem of getting the network and sharing device recognizing that I am actually connected to a wireless network. I can't use my printer or share files with other people. I can't get my wireless printer to work if I restart my computer and I have the documents I want printed already sent to the printer. My network and sharing Center also works very well for a few seconds when I start my computer then it turns off again.

  Hello

  Method 1:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  You can also view the related items for more information.
  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  Method 3:

  Setting up a wireless network

  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network

  Wireless network card: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions

  See also:

  Connect to a network with Windows Vista wireless

  http://TechNet.Microsoft.com/en-us/library/bb878035.aspx

• I have problems wireless on my Acer laptop which has Windows Vista. I am able to connect to my school of university network and used to connect to my home network.

  original title: Wireless on the Fritz

  I have problems wireless on my Acer laptop which has Windows Vista.  I am able to connect to my school of university network and used to connect to my home network (both are networks limited requiring a password or log in).  However, last week my computer stopped connecting to my home network (no one else has this problem with the home network).  I tried to fix the problem, but my computer says that "Wireless association failed because Windows did not receive response from the access point or wireless router."  That said also thatthe connection "(my wireless network)" has been cancelled.  This is perhaps due to a timeout or user action. »

  The only different thing I did last week was click option at my University 'connect long-term' instead of 'connect short term' to their wireless network.  Maybe who has messed up my settings?  That's what my University said of his record long term: "students, faculty and staff also have an option to easily record their computer (or other wireless devices), so that it is not necessary to authenticate each day they connect from the network wireless campus, to resources outside the University.»  However, these settings are saved on their network (I can access it online from another computer), so I think it is unlikely that he messed up my settings.

  I don't really know what the problem is.  Any ideas as to what I can do?  I don't want to reset my computer everything.

  Thank you!

  Hello

  You can view these methods:

  Method 1:

  I suggest you to disable any program of security on your computer and check if it solves the problem.

  After reviewing the question you must reactivate the security on your computer program.
  Note: Run the computer without antivirus software or firewall is a potential threat to the computer; Be sure to activate security software after completing the troubleshooting steps and after identifying the problem.
  Method 2:
  I suggest also allows you to check in SafeMode with network.
  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode
  Method 3:
  I also suggest you to check the settings of the router firewall.

• Windows Vista connected online but not shown on network and sharing Center or on the taskbar, leads to other problems

  I have a Dell Inspiron 1520 running on Windows Vista, my router modem is a Motorola SURFboard SBG901. A few months ago on this computer, I couldn't see that I was connected online either from right down icon in my taskbar (it shows just two monitors with an 'x', that when you highlight on he says "not connected, you are currently not connected to any network.")  I don't see it on my network and sharing Center which States: "not connected wireless connections are available." In terms of network it shows that my PC and then the line that has an x on him. If you click the x, or select diagnose and repair, he informs me that all is going well with my computer. If I go to connect to a wireless network, it shows that I'm connected to my network ready. I open one of my browsers and they all work very well, I can access any site without problem. I was not embarrassed with him at the time, but since then I moved into a new House and have a new service and everything, with this motorola modem cable. my new wireless network is a network unsecured, which of course, I want to fix it. I can connect to this network, but I can't access it through Windows properties to make sure. I read the manual of the modem, telling me to connect through an ethernet connection and access configuration manager using the ip address of my router on a browser, but which does not charge or the other. I have other devices (Ipod Touch and PS3) wireless I got other people come computers and they all detect the network but cannot connect to it. Thanks for any help.

  Hello
   
   
  I would like to ask you a few more things.
  1. how many network connections you have created?
  2. are there multiple NICs installed on the computer?
   
   
  Since this is a common problem and many users have solved this problem by using different methods.
   
  This can also occur if you frequently use several type of internet connections such as dial-up, Ethernet and LAN.
   
  As the article below also indicates that there could be multiple reasons for the same.
  The network adapter icon incorrectly displays a red "X" in the window management in Windows Vista network connections when the network adapter is connected
  http://support.Microsoft.com/kb/945925
   
   
  Method 1.
  I ask you to remove any network connection if you have created and then check.
   
   
  Method 2.
  For control please check in mode safe mode with Networking if the problem exists.
  Here's how:

  a. restart your computer.
  b. when the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows 7 Advanced Startup Options.
  c. using the arrow keys, select the desired option of Mode without failure.
  d. press the Enter key on your keyboard to boot mode safe mode of Windows 7 with networking.
  e. when Windows starts, use check and Internet explore if the problem persists.

  For more information, see the articles below.

  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

   

  Troubleshooting in safe mode
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshooting-problems-while-in-safe-mode
   
   
  I hope this helps.
   

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• A2109 2 problems with networking and an HDMI output

  I had an A2109 for Christmas and have 2 occurring of questions that I need help on.

  1. I was never able to get the HDMI to work. I tried 2 different cables, as well as 2 different TV and when I plug the microphone to the Tablet and the TV, my TV cable don't say no signal source. I got this tablet specifically for the HDMI output and flash support, so I can watch sports on the internet on our main TV.

  2. in the last week or so when I wake up in the Tablet, my apps does not connect to the internet. In the taskbar it shows that I am connected to the network. I open up chrome and you get a DNS error. To solve this problem, I turn off the Tablet and then turn it back on. This happens whenever I wake up.

  I've not being updated to JB again because I don't want to lose the capabilities of Flash

  As I have a follow-up has been able to solve these two issues.

  HDMI: the cables, I bought two bad ones were apparently. I bought another and that he had "snap" in as well and the TV started to show what was on the shelves. How lucky I am with this one?

  Network: Restarted my router and after a few days there were no problem.

• I bought the new iphone 6 s more and I have not configured, I just opened the phone and charged, but after some time it stop by itself, is this normal or I have a problem with my phone?

  I bought the new iphone 6 s more and I have not configured, I just opened the phone and charged, but after some time it stop by itself, is this normal or I have a problem with my phone?

  You need to activate the phone. There is nothing that the phone can not be activated.