Cisco Wireless

Well, do not really know where to askBut what is described Cisco router-point of access is great and fearsome performance for a domestic use, but cisco is still for sale? If so, can someone give me a link to the list of products?Think so just to clar

Hello world I'm pretty well EAP works, however with the help of LEAPWhen I get to PEAP and EAP-FAST, I can't make it work What am I missing, I don't know that EAP-FAST and PEAP require certificates. However, how to configure their client side?Hope yo

Documentation, I see that it should be possible to connect end devices like for example cameras to the Port PoE Out of an AP from 1552. Is it also possible to connect another TURN to the port? Drawing.jpg In the scenario that precedes the AP 1552 can

Hello: Today, I converted an access point AIR-CAP2602I-A-K9 to stand-alone using the mode button/tftp, but any IOS Installer (I tried 2 other IOS and also tried to enter Rommon - I am able to change IOS because that the procedure I used is a not any

(Note: a 629648353 of TAC on this ticket and no solutions have yet) Hello I m installed a vWLC on an ESX 5.5 according to the Configuration Guide (vlwc version 7.4.121 and tried the last one also), and if I put a tag of Vlan on the interface of manag

Hello I'm looking at deploying Cisco 1552 s developed in multipoint mode. I would like to know if its possible to connect wireless clients directly to the AP when mesh to the point to multipoint mode? Documentation (below), mode of wireless links all

Switches: 3560 routers: 2811 AP: 1552e We have 4 1552 AP we would like for installation in a point-to-point environment. Currently, they are light but would make us independent for this scenario, unless there is a feature in the controller that would

Hello can someone help me how to STROKE running 1.4 FT statistics? I installed insurance license with 50 cameras/monitor set / exporter on WLC (current version 7.6) but I can not see the statistics of any request under the dashboards of detail. If I

I recently inherited a network of mesh of all 6 PA campus and 14 cards. We have 4 switches remote, met through cards. As-is, the network works, but there are things that we would like to clean and sustainable on the local network. In their current st

Hi guys,. I hope someone can help me with the following problem, I am confronted with... I have a vWLC 7.3 deployed in our HQ site running. At Headquarters, we have a deployed W2k8 R2 NPS to works very well for VPN, router and switch authentication I

After having modernized our Cisco MSE 7.4, the device is not connected to the network.  Once the device is restarted, layer 3 echoes occur for about 2 minutes and then stops.  The only way so he can answer once again is to reboot the device.  Once ag

Hello As of today, we moved 2 access points Aironet in our company to allow customers wireless like the macbooks, iphones and other devices. I have installed two access points the same way (although they are on 400meters apart from eachother) and the

Hello I tried everything and searched the net for it without a bit of luck this time. I found a few years ago, but now I can't. I want to make a graph with http://oss.oetiker.ch/mrtg/ that list the number of clients that is connected. I know it's pos

Hello all,. I just bought three 3502i access points and a hard time getting them to communicate with my controller 2106.  Currently I have the APs connected directly on the port of PoE on the WLAN controller.  From what I've read so far that it shoul

Hello It's probably a stupid question but this is. I have LWAPPs a WLC with ACS using EAP - TLS with a backend ActiveDirectory. I connect a laptop to the network with a wired connection and the connection to the domain. The cert of the user is then p

Hello! We have 1941 SRI with builtin WiFi-AP that uses three antennas. I want to cover three floors with this access point using external antennas to separate floors. The left and the right antennas can be used for transmission and reception and comm

I have this design to implement. 2 sites.  on the Wan, there are 3 layer communication. Site 1 access points, I want to have the Site1 controller PDC, but also I would like the exact same APs have backup controller the controller of site 2. I'm assum

I have a 1140 Access Point.  I noticed that the AC adapter came not in the box. Maybe because it was poweroverethernet. My question is there an advantage to using ac vs poweroverethernet adapter?

Hi all I have a WLC 5508 in SHIFT mode and 14 1231 WAP connected on it already. However, I still spend my old controller 4404 9 WAP more towards the new 5508 controller. I can't get remaining 9 WAP register with new WLC. I found the rest of the WLC d

All, The configuration for my 801AP is attached.  I would like to hear all the recommendations that the forum members can have on my configuration because it is enough 'vanilla' such that it has been created from the GUI interface. I would be gratefu