Dell Switches

Hello I'm trying to setp an ACL on a powerconnect 6248 switch that allows traffic from certain hosts on a VIRTUAL LAN to another VIRTUAL local network.  I tried the setting up of an ACL to do this, but it does not work.  What would be the correct syn

I, m having a problem accessing internet to vlan 10. I can ping everything of all the VLANS. My internet router/firewall is on ethernet 1/g11 and has an ip address of 192.168.5.254. I have no problem accessing internet to vlan 20. I add a static rout

It is easily possible to Exchange routes using a 6224 for a Cisco 7204 OSPF? My cisco has always been eigrp between all other routers. I have OSPF enabled on the cisco as follows: router ospf 100Log-adjacency-changesredistribute subnets eigrp 1networ

Hello I am to set up the switch of PC5424, I set the admin/password and IP through the wizard of initiation. Access this switch using the IP through IE and I configured two VLANS in the pages web of DELL OpenManage Switch Administator and then I appl

Hello I am trying to access the table of dynamic addresses via SNMP, with a PowerConnect 6248 switch. I tried to follow the instructions [1], as other parts of the BRIDGE-MIB are ok on this switch. When snmpwalk'ing BRIDGE - MIB:dot1dTpFdbEntry, I ha

We have a stack 6224, we use two vlan on it VLAN network 10.1.1.X 24 10 VLAN network 192.168.0.X 24 40 Our workstations reside also in the 10.1.1.X network, so we need to administer the switch there. 192.168.0.X traffic must be routed to 192.168.0.X

Trying to trunk one VLAN of the 3560 to the 2724 via ports of SPF. The VIRTUAL LAN has been created on the two switches and ports of SPF are also members here. The built-in SPF port tool diagnostic claims everything works, but it is not permanently m

It is always in the phases of construction/test, but I'm having a problem with the following text: VLAN 100, 150, and 200 are in the forefront with networks are 172.17.100.0, 172.17.150.0, 172.17.200.0, respectively, and their interface addresses are

Hi all I have a very frustrating problem with routing using a PowerConnect 6248 switch. Network configuration is the following: VLAN3 172.16.0.254/24 VLAN4 192.168.0.254/24 PC on each VLAN using the switch VLAN interface IP (x.x.x.254) as the gateway

I changed the ip numbers in this example of those public to the private sector | IP switch of the provider: 192.168.0.162/29. ------ | Reference Dell 6248 ip: 192.168.0.164/29 | ------ | Halon SX 200 ip: 192.168.0.166/29 | A Halon router for ip trace

Hello I try to use 2 6224 switches QinQ purposes. The two switches are connected via links XG 2, for reasons of redundancy. The two switches are: interface ethernet 1/g11Auto mode channel-group 1«Cisco links» descriptionoutput!interface ethernet 1/g1

I'm quite a newbie to the Vlan bare with me: I have users on the network that is shared by other companies (1 network, many businesses). I want to segement my people from the rest of the network for security and reduce network traffic. I have a power

I just upgraded our office in two PC 2748 s (while still also using one of our PC 2324 devices) and I would like to know the best way to connect these three switches. At the present time, I have a cord Ethernet connecting each of the 2748 s via the 4

Hi all I have the following problem: I want to connect a new PowerConnect 6248 switch to your existing PowerConnect 6024 that acts as your central router. Everything works fine so far. I connected the two switches via ports, created a GAP them config

I tried access the switch using the default IP 192.168.2.1 and can't find it. I was literally out of available ports before the purchase/installation of the 2724. Our network is 192.168.0.x with a subnet of 255.255.255.0. Currently, the managed Mode

I am looking for information on how to build an aggregation of links between my powerconnect and three cards broadcom on my server. I want to create a bandwidth of 3 GB. I created a team with suite ABEC 3. My network have 2 VLANS. At this stage, I co

Hello How set up a battery of PowerConnect 6248 switch with 3 or more 10GbE-commissions only 2 work, weird! Firmware is up to date. Two 6248 with 2 10GbE batteries are ok, I was expecting that a stack of 4 with 4 s 10GbE work :-(. Stacking shoud go t

Hi, I switch from telnet to ssh, but I do not see where to disable the telnet service. Any help? Thank you JP.

I just run the wizard from initial configuration to a PowerConnect 3448 and entered the wrong subnet. Can I change the subnet without erasing all parameters and rerun the wizard? Thank you

I'm confused about the VLAN. I thought that the notion of VLAN was this computer on different VLANS were not suppose to be able to communicate with each other. I am setting up a 6248 and for me to get DHCP to work, I need to enable ip Routing. When I