6008 USB shows the digital signal with nothing plugged

Similar Questions

• SPA112 line showing off as hook with nothing plugged

  I have an ATA that will record, but Port 2 is still showing the hook under Off status. There is nothing connected to the device outside a network connection and a power supply. This behavior always occurs after a restart, an update of the firmware and also a reset.

  Phone 2 could be faulty.

  You can check what is happening using syslog, but I suggest you consider an RMA number.

  Kind regards.

• frequency of the digital signal 6009

  Hello, how to generate the digital signal with frequency 50 Hz using NI USB-6009?

  You can take a look at this:

  Can I use a generation of impulses with the counters on the USB-6008/6009 case?

• PCI-MIO-16-1 shows the digital inputs 1-7 on, without same cable connected

  Max, my PCI-MIO-16-1 shows the digital inputs 1-7 as having entries of tension without same cable connected to the Board. No amount of spin with her (to the MAX) seems so he can act correctly in input or output mode. It's true, there are voltages on these pins. If I connect my cable (to a TBX-68 block), I see that it has on $line0 (on port0) 0v, 5v on line7 and 2, 5V on the rest. Trying to put these lines to something else in MAX seems to do nothing. (I also can't control the OD, either.)

  This card has tried to get a couple of have Weiwei at high speed. Now that I'm branching out, I found a strange behaviour. Of course, I tried to restart and turn off the computer and turn it back on. Automatic test MAX Returns instantly with a message "transmitted", that gives me hope, even if I don't trust the speed at which it seems to perform the check.

  I'm a complete noob at this stuff. Is there something obvious that I might be dominant? Is there a way I can test more deeply that the card works as it should?

  The open connections to the TTL inputs are usually detected as logic 1. You are not testing properly. Connect an entry to two gnd or + 5V. Don't let them ever floating.

• my internet connection is showing the yellow signal

  Sometimes my internet connection is showing the yellow signal on my taskbar system, sometimes the Internet will connect automatically and normally. But sometimes Internet works after restart or stop and re acting on the system, sometimes showing red X mark the Internet Signal in bar tasks. I can't find what is the real problem on my Internet.

  Hi Vincent,.

  The yellow sign can occur if the network drivers are not installed properly.

  Method 1: Run network troubleshooting and check if that helps.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2: Update the NIC drivers and check if the problem persists. Check out the following link to update the drivers.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Hope this information helps.

  Answer to us if you have any questions.

• MCE only receive digital signals with Toshiba USB hybrid TV

  Hi, I have a problem with the USB hybrid TV, I want to use with Windows Media Center, it works fine, but I can see only digital Tv, no cable Tv. If I use the software provided with TV usb I can see digital cable and cable, but with Windows Media Center only digital television.

  Can someone help me please?

  Thank you!

  Luca

  Hello Luca

  Please don't be crazy about me, but you have to understand that maybe it's not possible to use the material in any desired combination. This product is designed for all the cell phones (not only for units with WMCE. Because of this manufacturer is it comes with own software.

  As you can see, it also works with WMCE and also digital. In my opinion it's the big thing. By the Way: AFAIK WMCE supports analog and digital TV by use of the antenna). Try Please also check some support WMCE or even forum WMCE site.

• USB-6008 to give the digital output

  Hi all

  I was wondering anyone at - it base an example of an exercise using USB 6008 to give a digital output of a VI in Labview.

  I am very new to the use of the USB 6008 AND Assistant DAQ and so far I've had reading a temperature, next step is I want the USB-6008 to give a + 5v output when the temperature reaches a certain value, I built a Labview 2009 VI for the temperature reading, but now I'm stuck on this piece.

  Any help is appreciated! or if there are examples of laboratory exercises that exist that I can perhaps draw.

  Hi Marko

  Please take a look at the link that has some interesting and intuitive video to use the USB-6008 housing and how to set up the device for several applications in LabVIEW below. Please take a look at the step by step videos and let me know how you go. They are under the tab '"virtual Demos.

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/14681

• time extraction of the digital signal

  Hello

  If I have digital signals from optical barriers and to extract the time (for a body that passes these 2 obstacles) how can I retrieve this day there using Labview.

  THX

  I have chata,

  Thanks for the answer, and I hope that your well.

  Here's an example I've done for a client, eager to discover the time of a flat section of its waveform.

  In your case, you must make a detection of pic on both codes, then less locations and a few x with the number of the sample to get the time.

  Let me know what you think.

  Kind regards

  James.

  PS Sorry code is a bit hasty.

• Connect the digital field with Drop Down

  I have a numeric field for the zip code and a drop for the city.

  I want that when I write the postal code in the numeric field to automatically display the city drop down list.

  And even when I chose to drop down the list then show in the digital field (postcode)

  I have all that in Excel.

  Thank you

  Use dynamic properties.

  Start by importing the xml from your spreadsheet (you're on your own with who) excel. Assuming that each line is a city and a postal code, your xml code will look like this:

  SomeCity

  12345

  .

  .

  .

  (1) in the designer, go to file > new connection of data...

  (2) select the sample XML data and the file in Excel.

  (3) make good properties sure dynamics are enabled, tools > Options > Data Binding > show of dynamic properties.

  (4) select your fall down and open the field in the object Palette tab.

  (5) you will notice that the list items is green and underlined. Select it.

  (6) for items, select the line

  (7) for the text of the item, select the city

  (8) for the value of the item, select the zip code

  You now have your menu dropdown bound to the data in your Excel worksheet.

  Now, just a bit of coding (brace yourself), in the digital realm for your zip code, in the case of output put:

  theDropDown.rawValue = this.rawValue;

  and to theDropDown:

  thePostalCode.rawValue = this.rawValue;

  Now all you have to do is import xml into your form to perform.

  Kyle

• Is it possible to measure digital signals with devices of simulations?

  The simulated device configuration is the following:

  9174 chassis cDAQ (cDAQ1)

  -9215 (cDAQ1Mod1) (analog in)

  -9401 (cDAQ1Mod2) (digital i/o)

  With a digital line (e.g., line 4), I create a single pulse

  ------^---------....

  where the circumflex indicates the pulse short and simple.

  Is it possible to use a digital line (for example, the line 0) in to measure it in the device simulated using a kind of direct/indirect routing?  If so, how a set to the top of the digital input read task essentially read the output on line 4, internally?

  Thank you.

  N ° as the DAQmx help explains, you do not have this ability with a simulated device.

• USB loses the external connection with hardrive

  Hello

  I have a new HP pavilion touchsmart 15 notebook PC 15 - n058ed with some problems on USB 3.0 in combibation with the Toshiba external hard drive.

  Sometimes, the connection is lost. So backup refuses to go. The message to reformat the drive to use it again.

  The hard drive is still powered. The laptop does not work. Turn off at night.

  Nobody knows what is happening.

  Best regards Jan

  Hello new probably,

  I'm sorry that the solution I linked you was too difficult to understand. I can certainly understand that as the site is not exactly easy to use. I'll give you a few steps to try until find us a solution that works for you. Please, try the steps what I am stating to you below:

  Step 1. In the tile Menu type 'Control Panel'

  Step 2. Click on Control Panel

  Step 3. Click Security / Power Options

  Step 4. Click on change power settings

  Step 5. Click on change advanced power settings

  Step 6. Scroll USB settings and disable the USB selective suspend setting

  This will prevent your system to put the USB drive in mode 'sleep' and should solve your problem. Please if the problem persists re-post and we can try additional steps. Thanks for posting this topic on the Forums of HP. Have a great day!

• Check the Wifi signal with 'wifi_get_status '.

  It's the code I use to check the wifi signal, this is the first time, but now it is far from the WE even I turn off the wifi. Please help me with this problem. Thank you.

  bool checkWifi(){
      wifi_status_t status = WIFI_STATUS_RADIO_ON;
      int i = wifi_get_status(&status);
      if (i == 0)
          return true; // Wifi On
      return false; // Wifi Off
  }
  

  Hey there...

  You integrate an incorrect value...

  bool checkWifi() {
      wifi_status_t status;
  
      if (WIFI_SUCCESS == wifi_get_status(&status)) {
          if (status == WIFI_STATUS_RADIO_ON) {
              return true;
          }
      }
      return false;
  }
  

• When I print to my HP Laserjet 4000, the display shows the data received, but nothing happens

  I have an old printer, HP Laserjet 4000 and a new computer with Windows 7. Printer is connected locally.  When I try to print to it, the screen reads the received data, but nothing happens. Help?

  Hello

  Try the methods provided and check whether the problem is resolved.
  Method 1:
  Check out the link and follow the steps.
  
  Why can I not print?
  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print
  Method 2:
  See the link, run the Fixit and check if the problem is resolved.
  
  Diagnose and automatically fix problems printing and printer
  http://support.Microsoft.com/mats/printing_problems/
  Method 3:
  Check the link and try the steps of troubleshooting described in the article.
  
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• How to properly install Adobe Creative Suite Design Standard (clouds pre-creative days) on the new imac with nothing other than the serial number

  I have cs6 Adobe Creative Suite Design Standard installed on my old macbook OLD pro (2007), and I need to also install this on my NEW imac (2015) as 2nd device. This product from adobe has been correctly registered in December 2012. I don't have the original installation CD (more there is no CD drive on these new devices in any case). I saw several download links, but I don't know which is correct (or if this is even the correct step). HOW to properly install my Adobe Creative Suite Design Standard on my new imac with nothing but my serial number? All I have is my online registration.

  (I'm even ready to uninstall the product on my older unit if it this will make easier, but as I get more than 1 my 1 license installation, I intend to proceed at the same time)

  Thank you!

  Just install it and activate it with your serial number (if it is compatible with your new operating system).

  Download and Installation Help-

  https://helpx.Adobe.com/download-install.html

  CS6 - http://helpx.adobe.com/x-productkb/policy-pricing/cs6-product-downloads.html

  You can also download the demo version of the software through the page linked below and then use your current serial number to activate it.

  Don't forget to follow the steps described in the Note: very important Instructions in the section on the pages of this site download and have cookies turned on in your browser, otherwise the download will not work correctly.

  CS6: http://prodesigntools.com/adobe-cs6-direct-download-links.html

• After installing my .ipa in iTunes and sync my iPad, the app just show the start screen but nothing else

  In collaboration with InDesing CS5.5 and contained Station 7.6.526 of WoodWing. I generated my .folio file. I tested in a content player Adobe 2.4.0 and each run ok. I perform all the process in the Bulider bleow my .folio and icons, certificates.p12 mobileprovision file viewer. When the compilation is finished I have donwloaded the .ipa file and added to my iTunes. After I sync my iPad icon appears but when I launch the App its show me the splash screen, but not the content of folio. In the index, I can see all the spaces that the app / folio needs for all items but not market show the content in any way. The .ipa file is 115 MB, so... must be something inside...

  Note: I work with content Station of Woodwing

  What I need to fix? Where is the error?

  Thank you!

  

  On your dashboard of DPS, scroll down to the bottom of the page and click on Contact and manage the Gold support.