Satellite L770 dosen't find USB devices

Similar Questions

• Satellite Pro A300 can not find USB devices

  Hello forum,.

  We have a customer who bought a Toshiba Satellite Pro A300 with us, but he gets a strange mistake about it.
  It connects to a hub 5port Sandberg USB 2.0 to one of the usb ports, the pc detects the hub, but when it connects a /Memory stick to the hub, nothing happens.
  the hub and the memory stick works on other PCs.

  I hope someone can help.

  Best regards

  John Bork
  DANBIT A/S

  Hello

  What happens if you connect the memory stick directly without this USB hub?
  I also had a USB hub, but these hubs are a little complicated and delicate USB specification allows a certain power and according to the devices that connect, you need to use an active USB hub, that means with external power supply.

  But normally, Satellite Pro A300 should have enough USB ports if it of needed, I would recommend a USB hub with 2 or 3 maximum ports

• Satellite Pro A60 PL: message: USB device can run faster

  Hello!

  I have a problem with the USB 2.0 drivers in my Satellite Pro A60 PL. everytime when I connect the message apear theres USB 2.0 device this device can run faster. What can I do about it?

  Hi guys

  I received the same message. It s not an error but a balloon tip Windows.
  I didn't find the reason for this message because my phone supports USB 2.0 ports too and I also connected a USB 2.0 compatible device.

  I've tired to remove the Device Manager, the controllers and the USB hubs and updated the Win XP operating system to the last State. I've also updated the driver chipset but sometimes (not always) this message again using a disc HARD 2.5 USB.

  I read in some professional computer magazines that this message is normal and it might appears with some SATA external USB hard drives. So you can ignore it.
  It s nothing serious.

  Greetings

• Satellite L450D not start - think usb device is connected

  Hello. I have a portable satellite L450D running Windows 7, which will not start. It gets to the loading of the windows with the windows logo page, but it will not go beyond this point.

  I tried repairing the system, and that tells me that a device is always connected to the laptop. I think it's maybe my phone, I had connected by usb last week. The usb cable is removed physically but the laptop obviously thinks that it is still connected.

  I'm passed through different service options - system repair, System Restore, restore the last good config, boot into safe mode but nothing seems to work.

  Ive tried to connect the phone while the laptop is trying to start and then disconnect it but still no luck. The laptop still think that the phone is connected.

  Ive not tridd remove the battery from the laptop, as it's apparently quite difficult.

  Any ideas anyone? Thanks in advance

  Hello

  I would recommend you check the boot order in the BIOS.
  Go to the BIOS by pressing F2 by turning on the device.
  Now, press F9 to get the default settings and save the changes press F10.
  Also check if you can disable the legacy USB if it s is not available, ignore this tip.
  Now, restart the laptop and test if it would boot from the HARD drive.

• Satellite C660-1JH: problem of USB device - software not installed

  Having had several attempts trying to install different software, Microsoft Fixit program has scanned and found that my PC has loopholes with USB points.

  The screen read: "the software device driver is not properly installed. Please consult the manufacturer of your device to help get this device installed.

  It also sets out the following...
  'Intel(r) ICH9 Family USB Universal Host Controller 2936.
  'Intel(r) ICH9 Family USB Universal Host Controller 2939.
  'Intel(r) ICH9 Family USB Universal Host Controller 293C.

  No idea how I can fix this please?

  Computer is Toshiba Satellite C660-1JH.
  Operating system is Windows 7, 64-bit.

  Hello

  Try removing the USB ports and hubs from Device Manager.
  Restart the device and wait Windows OS has reinstalled all USB controllers once more.

  If this is insufficient, the chipset driver update because driver chipset controls the USB controller.

  Here you another thread on chipset driver;
  http://forums.computers.Toshiba-Europe.com/forums/message.jspa?MessageID=249306

• Satellite M40 (PSM42) - boot from USB device

  In the BIOS of my Satellite is not any choice to begin with USB (only floppy drive, disk, CD). Is it possible to use a USB - HDD for booting (instead of the internal drive)?

  Hello

  You can start only this features:
  USB FDD, HDD primary, optical devices, network (LAN)

  You cannot boot from USB HDD.

• Satellite A30: Does not recognize USB devices.

  My computer does not recognize any devices when connected to the USB Port on my Satellite A30. After downloading SP2, I was able to install the printer, but I can't use it because there is no printer icon in the toolbar. If I want to print something I get the window of the printer, select printing, then it goes to the author of the Image of MS Office. Basically, I can't use my printer or any other device connected to a USB port.

  However, it was working perfectly fine when I had the home edition of XP but I can not reinstall this one because there is something wrong with the recovery disk that's why I had to install XP Pro.
  Also, I used to get a sound, letting me know that a device has been connected. I get more or the icon in the toolbar.

  Is that what I could do to fix this please? Is it possible to get another disc of recovery somehow? Obviously, it's something to do with XP Pro software, but I don't know what to do.
  Could you please help me?

  Thank you!

  Hello

  If you get a window of the printer you need to select the right printer. If printing goes to MS Office Image writer so the right printer is not selected.

  On the new installation: If you install the operating system from the original Windows CD you must install the necessary drivers and QFE patches all in the right order.

  USB port: I found a useful paper on this topic:
  http://support.Microsoft.com/kb/873169/en-us/

  Good bye

• Satellite A200 not power external USB devices in mode 'sleep'

  I have a new A200. I have and USB hub and disc external hard USB powered. When I put it in mode 'sleep' their lights stays on. It came with Vista. I searched for the setting, but I could not find. It is not good for the battery. Any advise?

  Thank you.

  -Sinan

  Hello

  The lights are also on when the laptop is to stay in sleep mode or hibernation mode.
  You cannot disable the led s

• could not find USB device & not print screen

  I'm sorry, but I have another question. I'm so sick of this. I swear that my system, the material is good (tablet of Motion LE1600 quite common with WinXP svc pk 3 & Security Essentials from a full reimage a month ago)

  All of a sudden today, my tablet is not my mobile phone which is connected with a USB cable, so ActiveSync starts. I messed with the USB cable and moved to another plugin. It plugs into the Tablet directly and not through the recharge base.

  In addition, at the same time, my USB keyboard does not at all on this pc. But the USB mouse works fine!

  So there is a problem with the USB plug-ins, I guess. Do not know what has been changed, but I've probably done something, or who knows...

  In addition, my e: drive drive USB which uses the Live Image to make full backups said it is in pause Mode. Don't know what it is, but I bet that it is not connected somehow, although if I look at my computer, I see e: listed there.

  And when I start my pc and connect, I get this pop up in the taskbar saying that some Windows delayed write failed for a file named e:\$Mft. The data has been lost (?). Since print screen will not work to create an image in Paint Shop Pro, it has been challenging trivia note.

  And I look at the table Motion, which helps you set up the Tablet and periphials, dashboard and under Microsphone, he said an input control limited - Knowles Intellisonic software is not enabled.

  I looked in all programs and in my computer > all programs and I see nothing named Knowles and Intellisonic. I have no idea what to do, TI, it is still important.

  Help!

  Solved (for now!). I went to F8 on reboot and did the last good known Configuration and it worked. I'm very happy now...

• Satellite Pro 6100 USB XP SP2 remove USB device after suspend

  I have a Pro Satellite XpPro 6100 running.
  I have a problem since I installed SP2 of XP in that USB falls when the computer wakes from sleep.

  The computer is up there, but I can reproduce this with SP2 only. Fortunately, I did a Norton Ghost and I restored the status of versions prior to SP2 for now.

  It does not matter what is connected to the USB port, or which port it's plugged. Out of sleep causes a ToolTip message in the taskbar on an icon that represents the USB port - and the message says 'USB device not recognized '.
  I can't find any help on the microsoft site, nor on the discussion group. I am at a loss as elsewhere where I can watch.

  Thanks in advance for any comments.

  Hello

  I put t know what USB device you use, but it is known to me that some external devices like DVD-ROM doesn t support the standby or hibernation. Try to remove the unit from the USB port and plug it back. I'm sure it should work again.

  Good bye

• USB devices not seen on Satellite Pro A60

  Hello

  I'm having a problem with my laptop Satellite Pro A60 running Windows XP Home: it is simply not to see all devices at all. Devices (USB, fan keys) are to be supplied with electricity, but I can find no trace of them on the computer anywhere. It is even not complain that they are not recognized - it's as if they were not there. I've uninstalled and reinstalled the drivers of hub USB root/controllers, but that has not helped.

  It is the latest in a string a glitches that can be helpful to know: a few weeks ago, the ATI Mobility Radeon 7000 IGP suddenly caused windows crash at boot time. I could just sort the problem by updating the bios and reinstall the ATI drivers (all toshiba). It is not of course the relevance, but after the bios update I also improved the 6 F-secure antivirus software. XX to 7.01.

  Usually, I try to get as much as I can by reading these forums but I'm not a guru of computing and on this one, I'm out of ideas - because Windows is not identify any fault, I don't even know what to look for on google... Someone has an idea?

  Thank you very much

  Philippe

  Hmm, you said that you have already reinstalled the drivers of USB controllers/root hub.

  But maybe you should try to make this again as a result of this procedure;
  -Disconnect all USB devices
  -go to the Device Manager and change the view to display hidden devices.
  -Open the tree of the USB controller and remove all controllers.
  -Restart the computer and wait until the OS has installed everything again.
  -Then plug the USB devices to the USB ports for laptop

  If this does not help, it would be desirable to recover the laptop with the Toshiba Recovery CD supplied.

  Good luck

• Satellite S1800-314 is slow if a USB device is connected

  I have a Satellite S1800-314 but its slow when I have stuff USB conect as dougle wireless or USB HDD and

  I am running Windows XP PRO 2002 SP2
  Is there anything I can do to make it faster?

  Hello

  In your case I would first update the chipset drivers. You can find it on the Toshiba site in * Archives *. In addition, you can update the BIOS too. Maybe this solves the problem with USB devices.
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  There are many things you can do to make Windows XP faster. Search Google for it and you'll find enough.
  Here are some examples of how you can do it faster: starting disable programs in msconfig, disable services that you n t need, defragment your disk at any time and so far.

  Welcome them

• System hangs after connecting a USB device in Satellite A110

  Hello
  I have a Satellite A110 (psab6c). Whenever I plug an ino device USB my computer it crashes and I have to put it off and then on again and remove the USB device. I looked for the drivers, but I can't find.
  I use Windows XP. Can someone help me? Thank you

  Riledogg

  I'm sure that there is a driver problem. See the manuals. It must be described how to properly use this external device.

• After the use of any USB device, I stopped the device that comes in the window telling me it is safe to remove the device and then my computer crashes I have to make a difficult start to resume what I was doing. It is on a Toshiba Satellite running Vista

  After the use of any USB device, I stopped the device that comes in the window telling me it is safe to remove the device and then my computer crashes I have to make a difficult start to resume what I was doing.  It is on a Toshiba Satellite running Vista

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
  all except the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  ------------------------------------------------------------------------------------------

  If no joy, see Toshiba Support and/or their forums:

  Toshiba support and drivers
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

  Toshiba Support Forums
  http://laptopforums.Toshiba.com/

  Contact Toshiba
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contact

  I hope this helps and happy holidays!
  Rob - bicycle - Mark Twain said it is good.

• Satellite A100-991 - cannot boot from USB device

  My Satellite A100-991 (MS Windows XP MCE, SP3) does not start from a USB key or USB hard drive. The same USB devices are bootable if they are connected to a desktop computer or a laptop from other manufacturers. I put the USB as the first boot device and use an image "Bart PE" on my USB device.

  In fact, I have installed 2.10 Phoenix Bios version and I wonder if I could update the BIOS by using the 'sa105v21.exe' program and that this would resolve the startup problem.

  Hello

  Have you tested different USB keys? I think that your current USB key is not compatible
  Also test the USB to different USB ports. A port may be defective for the computer to start t with him.

  Theoretically, you can try upgrading the BIOS but don t forget s a bit more risky and it should be the last step.
  Prior to this, load default settings in the BIOS and check if you can boot from USB.