Dell Servers

Can I install Virtual Machine in T310? Hardware is supported with it? Thank you

Hi all I have so few R610s I want to upgrade the memory on. I have read the documentation I found to support, but I'm still a little confused. They are all single-processor (the A side) with six 2 GB DIMMS. (12 GB total) I need to upgrade to 20-24GB.

My R810 is currently equipped with 64 GB (16 x 4 GB) of DDR3 8500R sticks and we were willing to bump up to 128 GB. We have four Xeons E7540 mounted. We bought four of ram ECC DDR3 of IBM-12800R (2Rx4, 1.5V, IBM part number is 00D 4968) which I think

Quick question... I find not a file of specifications on the R710 internal USB.  Is this 2 USB or USB 3?  USB 2.0 would be fast enough to install the Core Hyper-V parent on an internal USB drive?

Server worked fine for almost a month because it is the last power down... Last night I turned the unit off and unplugged it re rearrange some power cables and clean the area... After a few hours, I plugged the unit back and press the power button an

Hi guys,. I need help in formatting of our server I think I messed something configuration or delete.We have poweredge r720 server in the office and we want to reformat the drive to become the new server. Here's what I did: 1. during startup, we go t

I have a PowerEdge R310 server with processor Core i3 and 4 GB or RAM (model number: M391B5773DH0-YH9). I bought 4 x 4 Go to the exact same specifications memory and installs when DIMS 1, 2, 3, 4, but the server does not accept it. I also tried Setup

Hello I have this R720 Server I want to install CentOS 6.3. It has two 256 GB partitions that have been previously configured as a RAID-1 volume. I removed it because we must not RAID and just need performance when it comes to disk read/write. Howeve

Hello people, I am trying to upgrade the firmware version 6.1.1 - 0047 to 6.3.3 - 0002. The operating system is Windows Server 2008 R2 - Standard - x 64 But the following message was displayed: The program cannot start or run due to incompatibility w

I have a 2950 III with 8 Fujitsu 146 GB drives installed in a RAID 10 array. The first six discs are configured for use in a virtual disk with the last two records configured to be used as a dedicated hot spare. OMSA describes the version of the firm

We have a 8 bays 3.5 "R720 with S110 base and want to switch to a H710.  It seems that we should get the mini monolithic version of the controller?  What is the part number for the appropriate controller? Also, I guess also the MX3P7 cable to go with

I just want to confirm before I replace the failed drive with someone who has experience. I am running openmanage have 2 virtual disks raid 1, the 1st shows two thin discs. The 2nd shows a failed drive. These are hot swappable disks and I have some r

In my new role, I inherited a number of servers managed until now by someone else.  One of them is a PowerEdge T710 with a Controller PERC H700.  There are two matrices; the other has four 3TO disks in a RAID-5 configuration. I don't need the storage

I have 2 450 GB Seagate drives (model ST3450857SS) in a server PowerEdge 2950 running Windows 2008 R2 with a PERC5 raid card.  2 disks are configured in Raid 1 and are in optimal condition.  I run the update package Drive_Firmware_V38WK_WN32_ES68_A07

Hello We have many PE2800 servers which are always good, but will not support Windows Server R2 2012 wanted to believe in the presence of the PERC 4e/Di controller. So it is possible to disable the on-board PERC 4e/Di controller and install a PERC 5/

Can I mix readers certified and not certified in my PERC 5 / I array? What's the story with the certified readers? Thank you

On the T320 w / 8 Bay hot swap and controller Perc H710... Can I use any SATA or SAS disk without any problems? I mean they must be good enough to be used in RAID etc but I mean the Dell is going to want readers only Dell? The reason why I ask is tha

Hello I have a problem with this device and have a new to replace the defective there is 2 of them on the server. What is the procedure to change this, regarding the server are stopped? Concerning Robert

Dear all, I have a Dell PowerEdge 1800 with above mentioned PERC configuration server. I have 5 X 73 GB 10 K HDDs installed, the total usable space is 340 GB [21 (drive C :) and 319 GB (drive D :)]. I have a free HARD drive slot and intend to add a H

I want to update the firmware H700 integrated into my new 12.0.1 R815 - 0091 to 12.3.0 - 0032. My first thought was to start from Systems Build and Update Utility with a copy of the am630_suu_a00.iso that I had downloaded, concatenated, and copied on