NI Hardware

Hello I try to use analog ForceFeedback on one of my lines on pxi 7340. The problem is that MAX always use encode as your comments even though I have set up as analog. MAX I disabled the encoder and activated the ADC suitable for axis and set the pos

Hello. I use NI9512 with the cRIO-9074 and engine P70530 stepper drive. cRIO needs a power supply. And if I understand right NI9512 both P70530 need external power. So, I need 3 power supplies? Or NI9512 and P70530 need only one plugged into the netw

Hello Please see the attached photos. failed.jpg showed that the system could not start when a device is slot in slot13 OK.jpg showed that the system is properly start. No device is inserted between slot13 to slot17. 1. place a PXI (PXI-8433/4, PXI-8

I would like to use the VISA API for working with modules in my chassis SMU-1062 q. I have installed the following modules in the chassis: 1 NI PXI-5102 (scope) 2 NI PXI-5402 (fgen) Instruments based on the registry as PXI modules are new to me for e

Using NI6124 and NI6541

Hi all When I inline in a Simulink model parameters, and when I run it in the SIT Simulation environment, it's as if they would not have been treated in inline mode. Each block of the model appears. And when I try to launch it on a remote target (PXI

How can I generate a sine wave of given the frequency of acquiring data 6251? I tried to use the generation of waveform of the signal processing Toolbox, but it seems that it is written that the first or the last sample, not all. I have faced this co

NI PCI - 6251 DAQmx, AIMD-752 motherboard, dual core processor, a lot of speed and the ram running WinXP Pro & LabWindows/CVI get DAQ-200016 memory overflow error when I try to generate a signal of analog output with a rate higher than about 32 000 s

I have a card PCI-6255 that I intend to use for certain sensitive measures. I'm trying to put together a budget-to-end error and I have a few questions. My model is in terms of number of analog-to-digital converter (also known as the LSB in your data

I use the express Signal as my data acquisition software. NI9239 Daq is data acquisition system is my data acquisition equipment. Problem I have is, regardless of the data rate and the number of samples, I put, I get a lot of samples. for example I p

I'm reading the analog input of a PCI-6111, who receives a square signal of 1 KHz with a cycle of 50%.  I put the sampling frequency to 1 MHz and wait until the data points are 1 usec outside.  When I check the signals received, it appears that the d

I run into some problems outputing a sinusoid of analog output with my acquisition of data using the sampleclock aboard. At one point, I was able to get the vi works pretty good and repeatable. When revisited however, I started to see error that the

I have problems with a simple LabVIEW program. I'm analyzing two inputs voltage and at the moment I have the VI work so that both are analyzed at 10 k Hz simultaneously and displayed in two tables of waveform.  What I would do, it is write values for

Hello Without the help of MAX, it is possible to modify/create an alias of the instrument on LabVIEW? Thank you JPLO

Hello I'm using Labview 8.5.1 and installed 4.5 VISA. I connected my computer to an oscilloscope Agilent DSO5014A via the ethernet cable. I installed the driver (I even tried the 2 versions found here http://sine.ni.com/apps/utf8/niid_web_display.mod

I am reading the temperature and to write a set from a Watlow 96 temperature controller value.  I searched the forums and downloaded a driver called Watlow96.llb by Brian Vibert (around 2003).  As far as I know, everything is set up correctly (corres

I have a NOR-GPIB-USB-HS adapter, turned on, the "Ready" light is on, the 'Active' light was not on. My GPIB device appears under devices and interfaces under Max, but when I click on "scan for instruments", it says "not found instrument." Is my adap

Hello Anyone can answer the question: Regarding materials traditional DAQ, for example the DMM OR-4060, how can I programmatically determine the number of device which can be seen in MAX? With the help of Labview 8.5, I looked into the following func